Search Documents

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By D. Beneteau, D. Milne

"Advances in technology provide educators with valuable tools to enhance their teaching and efficiently deliver content to larger audiences. University educators are often encouraged to become more “research intensive” and to increase student enrollment. Faced with these pressures, there is a tendency to use technology to improve teaching efficiencies rather than to enhance existing teaching approaches. Practical learning in applied engineering courses would suffer greatly if hands-on experience is not emphasized. This paper discusses advantages and limitations of new technologies applied to learning, and methods to incorporate more hands-on experiential teaching techniques to applied mining engineering courses.RÉSUMÉ Les avancées technologiques fournissent aux éducateurs des outils intéressants pour rehausser leur enseignement et livrer efficacement de la matière à de grands auditoires. Les éducateurs universitaires sont souvent encouragés à devenir plus « axés sur la recherche » et d’augmenter l’inscription d’étudiants. Face à ces pressions, il y a une tendance à utiliser la technologie pour améliorer l’efficacité d’enseignement plutôt que de rehausser les approches existantes d’enseignement. L’apprentissage concret dans les cours d’ingénierie appliquée souffrirait grandement si l’accent n’est pas mis sur l’expérience pratique. Le présent article discute des avantages et des limitations des nouvelles technologies appliquées à l’apprentissage et des méthodes pour incorporer plus de techniques expérimentales pratiques aux cours de génie minier appliqué."

Jan 1, 2016

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

By D Marshall

The sub-level blasthole benching method of mining has been proved to be economical at Willroy Mines. How-ever due to the nature and attitude of the wall rock, this method is susceptible to serious hanging-wall dilution of the ore. Attempts to solve the dilution problem by various means were not satisfactory until long Stressteel bars were employed as rock bolts. The adoption of this de-vice does not require any special skill, and has become routine in the under-ground operation. Since the inception of this method, the dilution of the ore has been greatly reduced and the ov1!r-all costs of controlling this dilution are much lower. INTRODUCTION T HIS is a report describing the successful use of long Stressteel bars as rock bolts in preventing l1anging-wall failure and consequent dilution in open stopes. Willroy Mines Limited is located (Figure 1) near the town of Manitouwadge, Ontario, approximately l1alf-way between Sault Ste. Marie and Port Arthur.

Jan 1, 1963

By H. A. D. Kirsten

SYNOPSIS This paper describes simple calculations to evaluate the stability of hangingwall and footwall strata at the work¬ing face and in backfilled areas. It shows that the benefits of support provided by backfill can best be realized when the fill is placed as close to the face as possible. The main beneficial effects of fill are that it reduces the stope span, at the same time providing a damping effect on vibrations, and prevents the fall-out of blocks in filled areas, thus maintaining the competence of the strata.

Jan 1, 1988

By J. Ran

"Hangingwall sloughing is the major cause of unplanned stope dilution in open stope mining. Understanding the hangingwall sloughing mechanism can guide the stope design in minimizing the unplanned dilution and improving muck size and therefore mining efficiency. Though the modified stability graph method may be adopted to assess the hangingwall stability, for mines where the hangingwall is inaccessible, the required parameters are difficult to define and some of the simple influential factors cannot be easily identified in this method to provide guidelines for stope design.This paper identifies the main modes of hangingwall sloughing in open stope mining based on detailed data collected from mined-out stopes and site observations, applies the voussoir beam notation to analysis of the hangingwall sloughing mechanism, compares the model analysis results with the collected stope data, and provides guidelines for stope design and model application. Finally, examples are given to demonstrate the time and support effects on hangingwall sloughing and stope dilution."

Jan 1, 2002

By AIME AIME

NEW YORKERS look forward to the third week of February as the time of the year when they can count on seeing their friends-from far and near gathered in the city for the four-day annual session of the Institute.., Indeed, the metropolitan district is so large that in engineer who lives in New, Jersey and has his office on the lower end of Manhattan island may easily pass a whole year without seeing an acquaintance who lives in Westchester and has an office near Forty-second Street. If the Institute served no other function than to provide a place where friendship may be renewed, ideas exchanged, and new acquaintances made it would still be worth while. But when about 30 technical sessions at which about 160 papers are read and discussed are compressed into four days the annual meeting is also entitled to high rank as an intensive course of post-graduate instruction in the newest development in mining and metallurgical technology. Last, but not least, it is the occasion of a good time for one and all, even if they do get more than a little behind on sleep before the end of the fourth day. Nine o&apos;clock is the time set on Monday morning for the beginning of registration, but a half-hour before that a number have always &apos;put in an appearance, and this is fortunate, because by 10 o&apos;clock four sessions had begun, those on mining methods, geophysics, a round table on the valuation of coal, and the session of the Local Section delegates. Three committees of the A. S. T. M. were also in simultaneous session, so the meeting may be fairly said to have started "in high."

Jan 1, 1931

By Sheldon P. Wimpfen

EVERYWHERE in mining circles the talk is of this new development of hard faced or insert bits which hints of many changes to come in mining practice and rock drill equipment. In the past fifteen years new equipment has appeared in rapid succession which brought one change after another in rock breaking practice. Detachable bits were an innovation which met with wide success. Blasthole diamond drilling has proven itself. Only recently, fusion piercing was announced as a possible solution to the problem of breaking taconite ores. For several years this interest in new methods has been growing and various experimental usages of tungsten carbides in rotary type rock drilling bits have been partially successful. American experts in rock drilling have been concerned with the subject for ten years but actual commercial practice was begun by European manufacturers and mining companies. At this time nearly every manufacturer of rock drilling bits is working on some type of an insert bit. On the Rand, European manufacturers are testing out various types of insert bits. The problems relating to rock drilling in South Africa vary greatly from ours. The bulk of the drilling there is limited to the 31/2-ft holes that are drilled for breaking the gold bearing reef ore. Rock drilling in most mines is far more diversified. Both drifting and ore breaking call for holes varying in length from 4 ft up to as much as 50 ft and more.

Jan 1, 1947

By Leonid M. Lerner

High temperature aluminum Alloy 8009 is a rapidly solidified/powder metallurgy aluminum-iron-vanadium-silicon alloy. This alloy in combination with hard oxide aluminum film has unique engineering properties which may recommend its use in compressors and impellers for aerospace applications. Various anodizing processes (including Sanford Low Voltage DC+AC Process) for these task will be evaluated and normal chemical composition, physical properties, and macrostructures of 8XXX aluminum alloys will be presented.

Jan 1, 2006

By Stephen van Duin

As productivity in coal extraction demands increase in underground coal mines, the industry is faced with finding new ways to support production without jeopardising safety. In modern mines the capacity and scale of longwall coal extraction has steadily increased to a point that support processes are failing to keep pace. In particular, roadway development is continually placed on the critical path of activities which maintain mine production, so any inefficiency in this area is quickly exposed. Original equipment manufacturers are under immense pressure to modify their machines to be more interconnected with each other, with machine communication and logistical sharing of space becoming a known requirement. This paper looks at the changing trends in mining practice, analysing available technology as well as currently emerging research into hard automation and discusses the need to integrate machinery and processes in order to see increases in productivity and safety.

Aug 1, 2013

By R. G. B. Pickering

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock?though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominately by means of scraper buckets and scraper winches?these were first introduced in the 1920s. Support is still mainly rock, either in situ pillars or backfill, or alternatively wood. Just as the mining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ?trackless mechanized mining? was introduced in the early1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to ?off the shelf? equipment. The move to introduce room-and-pillar mining into the narrow UG2 reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long hole drilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds?maximum reef recovery with minimum waste dilution.

Jan 1, 2002

By J. H. Douglas, A. F. Matheson

"The Hard Rock is the most easterly producing mine in the Little Long Lac area. The Company was formed in 1934 to develop a surface showing of gold in quartz made by a prospector, W. W. Smith, in 1931. Although some ore was eventually produced from this discovery, the principal orebody, hidden below 10 feet of muskeg, was found about 1,000 feet to the north by exploratory diamond drilling early in 1938 from the No. 2 shaft workings at the 250-foot level.Production started in 1938 and to January 1, 1947, 201,000 oz. gold had been obtained from 1,165,282 tons of ore mined and 869,397 tons milled. Of this ore about 15 per cent came from the development and mining of the original orebodies discovered at the surface. The remainder came from the ore found by the underground diamond drilling done in 1938. Of the latter ore, the Company estimated, at January 1st, 1947, only 140,000 tons remained. The orebody, therefore, contained approximately 1,100,000 tons.OREBODIES AND GENERAL GEOLOGYThe orebodies of the Hard Rock mine are of two main types: the quartz ore of the south and No. 1 shaft zones, and the sulphide ore of the north zone. The quartz ore consists of white quartz veins mineralized with sparse, fine, light-coloured pyrite, or, less commonly, nests of coarse, crystalline, light pyrite. A little tourmaline, scheelite, pyrrhotite, chalcopyrite, arsenopyrite, and native gold are also present. Native gold occurs in a few places in quartz veins in exceedingly rich cemcentrations, apparently where there are large, light-coloured, pyrite crystals of imperfect form. The ore of the north zone is massive pyrite with arsenopyrite and in places pyrrhotite. Many short irregular quartz veins, from a few inches to 2 feet in width, are also present, but the quartz forms a very small percentage of the whole. The veins may be flat to vertical, and sulphides on one or both sides replace the host rocks. The gold is closely associated with the sulphides . The quartz is commonly barren except where it contains sulphides or along the borders of the sulphide ore zone where native gold is not uncommon in quartz stringers."

Jan 1, 1954

By Bryson D. Trexler

Man&apos;s activity in developing, operating, and abandoning a mine often affects the quality of the ground water and surface water. Acid water drainage from mines is an example of an impact from mining that results in degradation of ground and surface water. New flow systems are created by the mining activity. The mining made possible complex chemical reactions that, with water movement, create a discharge of low pH, poor quality water. Remedies for these problems fall into two general solutions: 1) treatment of the end product and 2) reversal of some aspect of man&apos;s disturbance of the natural system. The relative reversibility of various aspects of man&apos;s impact from mining activities ranges from relatively easy to very difficult, from economically feasible to economically infeasible, and from technically possible to essentially impossible with present knowledge. The relative reversibility of a mine-related problem cannot be assessed without first understanding the detailed physical interactions that combine to form the problem. Acid water drainage is a combination of the availability of several chemical factors with the availability of water for a transport mechanism.

Jan 1, 1982

By D. Brandt

The Dos Pobres Mine is a copper oxide heap-leach operation located near Safford, AZ. Mine production is 163 kt/d (180,000 stpd) with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority. The engineering department began a project to improve fragmentation through blasting and thus increase throughput in the crushing system. It soon became clear that input from other departments was going to be required to make this a safe and economical project. Therefore, the crush and convey and ore control departments worked together to evaluate all available data on blast patterns and explosive loads and tracked performance and results. Using image analysis, drill energy index and databases, improved fragmentation size has been achieved and results have been verified while controlling costs.

Jan 1, 2011

By Wern-ping N. Chen

Pressure tunnel includes water-supply tunnels and tunnels for hydroelectrical power plants. Their design principles are different from those of water/wastewater/conveyance and transportation tunnels. Though theoretical pressure tunnel design guidelines exist, a comprehensive guide to summarize these guidelines to facilitate the planning and design of a pressure tunnel program is lacking. The purpose of this paper is to fulfill this need. It first provides key pressure tunnel design concepts in hard rock environment; then, it illustrates associated final lining design principles, including the design of un-reinforced concrete lining, steel lining, and reinforced concrete lining. Design diagrams and a flowchart for the reinforced concrete lining design are provided.

Dec 1, 2022

By D. F. Malan

"This document highlights some of the topical problems associated with the design and support of deep tabular excavations in hard rock. The displacement discontinuity boundary element method has been used for at least five decades to analyse stress and displacement distributions around narrow width excavations with complex plan outlines. The assumption is made in most cases that the rock mass surrounding the excavation is perfectly elastic. Although this approach works well to minimise stress concentrations in practice, it has limitations as important parameters, such as the effect of mining rate, cannot be investigated. Recently, a limit equilibrium model has been studied as a means to enhance standard layout design exercises by including an interactive on-reef damage model. This approach can include explicit energy release dissipation computations. A second problem faced by engineers in the mining industry is the evaluation of pillar and remnant stress. The paper highlights two aspects namely the effect of element size in displacement discontinuity modeling on pillar stress and the difficulty to estimate the effect of total closure on the regeneration of stress in old mining areas. Regarding the support of the tabular excavations, current efforts are focussed on providing improved aerial coverage using hangingwall bolting and temporary nets. An unresolved issue is the installation of permanent mesh in low stoping width areas. INTRODUCTIONSince 1886, more than 50 000 tons of gold has been mined in the Witwatersrand Basin of South Africa (Hartnady, 2009). The nearby platinum mines also saw significant growth in recent years and more than 80% of the world’s platinum group metal reserves are contained in the Bushveld Complex of South Africa (Nell, 2004). Apart from the economic aspects, the mines served as an outstanding rock engineering “laboratory” for many decades owing to the deep, tabular nature of the excavations. The period from 1960 to 1980 was especially lucrative in terms of research and world-renowned researchers investigated the support and rockburst problems (e.g. see Cook et al., 1966; Salamon, 1968; Bienawski, 1973; Wagner, 1984). Many of the rock-related problems nevertheless persist up to the present day and this paper explores some of these problems and recent progress. The production of gold declined substantially in recent years (Hartnady, 2009) and well-directed rock engineering research can play a meaningful role to slow this trend. The objective of the document is to highlight critical areas requiring additional research and not to discuss the topics in detail. The reader is referred to the many references for additional information. The paper only focuses on three areas namely numerical modelling, pillar stress estimation and aerial support. Although these are diverse topics, it is included in one paper to illustrate the many unsolved and practical problems associated with deep tabular excavations."

Jan 1, 2015

By A. Mei, F. Amadini, F. Cernera, D. Baliani, A. Flor, M. La Morgia, F. Sassi

The risk of TBM jamming because of squeezing rock mass or excessive caving (instability of the cavity) conditions is always a focal point while boring long and deep tunnels with shielded TBMs. Mechanized excavation provides a large amount of real-time data, for each machine’s parameters. Several analyses have been executed to assess the correlations between different sets of TBM parameters for the exploratory tunnel. Instead of analyzing the full dataset, a different approach is proposed, with data processed sequentially to simulate the real excavation situation. The probability distributions are recalculated together with their statistical parameters while advancing. This approach is extended also to the training of a Machine Learning model able to foresee the behavior at future rings based on past rings (using a Recurrent Neural Network). The predictions show a promising first step toward creating practical tools that can assist contractors and designers to correlate and predict TBM excavation data. These tools will assist to predict and quantify high risk situations that could arise during excavation.

Jun 13, 2023

By Doug Harding

The Metropolitan St. Louis Water District’s Project Clear is a 28-year program targeting wastewater capacity throughout St. Louis, MO. The extensive program includes the Jefferson Barracks Tunnel, running parallel to the Mississippi River at 2 m ID and 5,400 m long. A rebuilt Robbins Main Beam TBM began boring but hit challenging conditions about 2,400 m in, including water inflows. A larger 4.1 m Robbins Main Beam machine will complete the remaining 3,050 m in limestone, dolomite, and shale. The TBM will utilize a high-powered, high breakout torque cutterhead along with enhanced 360-degree probing & grouting capabilities to detect any karst formations.

Dec 1, 2022

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d&apos;excavabilité sont souvent en grande partie ignorés. Tandis que le choix d&apos;une méthode de percement économique est évidemment une priorité claire dans l&apos;étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By T. N. Williamson

The art of drilling tunnels is still in its infancy, although it is 70 years since the first tunnel driver was put into operation. (It was used to drive 6000 ft of tunnel under the English Channel.) But during the next 60 years neither government agencies nor private enterprise could find much of a future in tunnel drivers. It was difficult to justify the heavy investments, labor was opposed to the machines, and there had been some spectacular failures. In the last ten years, however, there have been changes. Tunnel drivers are being tried with increasing frequency-in spite of the fact that a large number of them have had to be abandoned on site.

Jan 7, 1965