Search Documents

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By Todd Minoski, Matthew McElhinney, Mark Mazzella, Morgan Sears, Craig Compton

The National Institute for Occupational Safety and Health (NIOSH) is staffed with Engineers, Geologists, and Field Technicians conducting a variety of ground control research. The mission of the ground control teams within the Mine Systems Safety Branch (MSSB) is to eliminate ground failures leading to mineworker injuries and fatalities. Advancing the science behind ground control relies heavily on conducting mutually beneficial research at participating mines which is detailed in specific references throughout the paper. The ground control teams have several types of field instruments at their disposal to measure the ground response in underground mines. These include borehole pressure cells (BPCs), vibrating wire stress meters (VWs), hollow inclusion cells (Hi-Cells), roof and rib extensometers, load cells, and convergence meters. These instruments are used to measure changes in pressure, strain, and displacement within the underground environment. Instrumentation data is collected automatically using intrinsically safe or MSHA permissible dataloggers if required. Information is transmitted to the dataloggers using approved cable to distances of 200–1,000 ft. depending on the type of datalogger being used. Once mining is completed, the dataloggers are retrieved and brought to the surface, providing in-mine data to mine management and engineers for the conditions currently being encountered in a particular mine. This data, in conjunction with geologic data and stress mapping, can be used to validate numerical models. The practical application of these models is extremely important for mine management and engineers, particularly when faced with more challenging mine environments. Insight gained from applying these models can be used to make better engineering-based judgments for areas that will be mined in the future. The impact of such applications can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 1, 2024

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By Changshou Sun

The geotechnical properties of mining zones at Leeville Underground mine (or simply called Leeville mine through this paper) are different from one zone to another. The typical ground condition is poor to very poor. Therefore, an appropriate ground control practice is the key for the successful and smooth ore production at Leeville mine. Based on the available geotechnical data, the empirical and numerical methods are used to design the right ground support systems. The main ground control practice at Leeville mine includes geotechnical data collection, evaluation of the stiffness of the support system, selection of rock bolt types, design bolt length and bolting patterns, development of the ground support standards, and performance of quality controls on bolt installation to ensure proper rock anchorage, and strength of shotcrete and backfill. Through all these activities, an appropriate ground support system has been established and applied at Leeville mine for the past four years. So far, a good result related to successful ground control and smooth ore production has been achieved, although the system is still being improved. The authors of this paper will summarize the ground control practice conducted in the last four years and will discuss the procedures and standards of establishing the appropriate ground support systems for Leeville mine.

Jan 1, 2013

By S. M. Hsiung

This paper presents the results of an extensive study concerning a series of roof falls in a room-and-pillar coal mine located in West Virginia. Three dimensional finite element modeling was employed to identify the possible causes for the roof falls. The effectiveness of possible roof control measures for alleviating or eliminating the adverse roof conditions is analyzed, discussed, and compared. The best mining alternatives are recommended. It has been found that large overburden depth and typical roof geology are the major reasons for the roof falls. Angle bolting may not solve the problem encountered in the mine studied. Changing the mine layout currently used in the mine appears to be the best alternative. The recommended pillar size and entry width which will eliminate the problem completely are 90 ft. x 90 ft. and 14 it., respectively.

Jan 1, 1985

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

By M. Ge

Pattison Mine is a small sandstone mine located in Iowa. The sandstones produced by the mine are not common construction and aggregate materials. The stones are used to produce a special type of sand for hydraulic fracturing, a critical technique for recovering tight gas and shale gas. These sandstones are very different from the minerals and rocks which have been studied extensively in mining. On the one hand, they are brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, they are friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, a research program was set up by the mine and Missouri University of Science and Technology. This paper discusses the preliminary results of this investigation.

Jan 1, 2012

By C. Haycocks

In spite of the increasingly high capital investment required for longwall mining equipment, there continues to be a steady trend towards this form of mining. This move is caused in large part by improved productivity of longwall mining systems combined with greater percentage of coal recovered over room and pillar mining, reduced manpower requirements, and the inherent safety of the system. Longwall mining is most amenable to the greater depths experienced by many mining operations, particularly in the coalfields of the Eastern United States. Two primary problems in the installation of a longwall panel are determining whether a particular seam is suitable for longwall and, secondly, type and capacity of equipment required for such a mining operation. In addition, recent legislation has forced an evaluation of the surface effects of longwall mining with a view to determining what, if any, surface damage might result from extracting any particular panel. These factors must be determined using large and often complex quantities of geological, structural, mining, and surface data. This makes the problem most attractive to solution using the computer.

Jan 1, 1979

By H. D. Dahl

In January, 1969, the Central Research Division of Continental Oil Company initiated a research program on roof control. The purpose of the research was to improve roof stability. Toward this end, it was necessary to determine which of the many geological and geometrical variables have a significant effect on roof stability. The isolation of these significant variables would allow research effort to be concentrated where it would be most effective in improving roof control. The research effort was directed toward two major objectives. One was to de-fine the geological and/or geometrical parameters that affect the severity of roof conditions in any particular area of the mine. This study was concerned with roof fall intensity. The second was to define why roof falls in Humphrey No. mine (and in northern West Virginia-south-western Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. This study was concerned with roof fall orientation. To provide a reference framework for further discussion, a geological description of the area is presented in Part II. In Parts III and IV, the procedures, methods, and 'results of the research applied toward the afore-mentioned major objectives are presented. Part V contains the conclusions and recommendations for-warded by this study.

Jan 1, 1971

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.'s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By S. Bhattacharyya

"Coal bearing rocks are low in strength and have geological discontinuities and moisture sensitivity. Roof and rib falls have been a major cause of fatalities in underground coal mines. Mine engineers design ground control plans for regulatory approvals. A number of tools are available from the National Institute for Occupational Safety and Health to design and assess these plans. Quite often there is not enough geotechnical input information available and databases are used. The Appalachian coalfields have extensive scientific studies to provide reliable regional inputs. Coal mines in the western United States and Canada have different geological and geotechnical conditions, and less available data. Use of inappropriate inputs in the tools like Analysis of Retreat Mining Pillar Stability, Analysis of Longwall Pillar Stability, and Analysis of Roof Bolt Systems may result in unsafe designs or over conservative designs. The tools are convenient but thorough understanding of the inputs, calibration with local test results, and operating experience are important for effective designs. The current paper contains examples of difficulties faced during mine planning using the above tools. INTRODUCTION Sedimentary rocks hosting coal are low in strength. Scientific studies have placed the uniaxial compressive strength (UCS), triaxial strength, tensile strength, and shear strength of sandstone, shale, siltstone, and claystone in lower range of strength among engineering materials (1). Coal bearing rocks are most often weakened by the presence of faults, folds, slickensides, bedding planes, fractures, and other geological discontinuities. The host rocks and coal are often moisture sensitive. The geological discontinuities allow water to enter the strata from surface and underground sources. This combination of low strength, structural weakness, and presence of water results in difficult ground control situations for the coal mines. Roof (2) and rib falls have been a major cause of fatalities in the U.S. coal mines. Modern underground coal mines necessitate wide entries to accommodate large production equipment. The gate roads, section entries, and the mains entries of a highly productive coal mine are as wide as twenty feet (6.1 m). The actual intersection width is nearly thirty feet (9.1 m). Adequate ground control is a key to maintain safe production in such mines. Mine engineers and their consultants routinely submit ground control plans to the regulatory authorities. While working out the necessary roof control system the mine engineers are required to demonstrate the adequacy of the proposed system. There are multiple ways to demonstrate this. Some engineers use traditional load calculation approach of roof bolts (3). Some engineers use numerical methods. Yet a large number of professionals resort to a suite of ground control design software offered by National Institute for Occupational Safety and Health (NIOSH) commonly referred to as “NIOSH Ground Control Toolbar.” These software tools are free and easy to download from NIOSH website. The software included in this package are: Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Coal Mine Roof Rating (CMRR), Analysis of Roof Bolt Systems (ARBS), Analysis of Horizontal Stress Effects in Mining (AHSM), Analysis of Multiple Seam Stability (AMSS), Analysis of Retreat Mining Pillar Stability - Highwall Mining (ARMPS-HWM). These tools are relatively simple to install and use in planning and designing coal mines and prospective coal mines. They accept a number of geotechnical inputs which are collected from either an existing mining operation or from exploratory boreholes. In the absence of necessary input parameters, the programs use default values which are drawn from databases of geotechnical properties built by NIOSH."

Jan 1, 2015

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By Xiaocen Lu, Guowei Li, Jiantao Wu, Thang N. Nguyen, Andrew C. Amenuvor

"This paper investigates the effect of driving a group of 52 open-ended Prestressed High Strength Concrete (PHC) piles on an existing highway embankment based on field measurements of excess pore pressure and lateral soil displacement. Excess pore pressure due to pile driving increased with depth and decreased with increasing distance from the pile, influencing a distance of 43 pile diameters. For pile groups, the rate of dissipation of excess pore pressure decreased with increasing depth and averaged 79% in 20 days, during which maximum ultimate bearing capacity was not yet attained. Lateral soil displacement continued to increase for a period of time after the end of pile driving and this could have resulted in significant inclination of piles if pile installation was too quick and pile spacing was too small. Lateral soil displacement due to pile group decreased with decreasing distance to the existing embankment as a result of high soil density produced by the embankment loading. The results also indicate that the effect of pile group installation on the existing embankment is negligible.INTRODUCTIONPile driving can cause excessive lateral displacement of soil and heaving of the ground surface, which may adversely affect nearby structures. In addition, lateral deformation and excess pore water pressure resulting from pile driving can exert lateral pressures and vertical forces on the piles, and impact negatively on the project and its surroundings. Therefore, it is important to evaluate the influence of pile driving on the nearby structures as well as the project itself when expansion works are carried out.Recent years have seen some development in the application of field tests for studying soil disturbance due to piles, and these tests usually involves pore water pressure and lateral soil displacement monitoring during pile driving. Results of field experiments performed by Reese and Seed (1957) in San Francisco Bay Mud with instrumented piles showed that pile installation generated large pore water pressures at the pile surface, with only slight increase at a distance of 15 pile diameters away. The measurements indicated that the increase in pore water pressures can exceed the initial total overburden pressure. Holtz and Lowitz (1965) reported a decrease in undrained shear strength immediately after pile installation, which was largely recovered after full pore pressure dissipation for field measurements within 1.5–2 pile diameters from the pile surface. Hwang et al. (2001) presented results of large scale pile driving tests where maximum excess pore water pressure generated decreased rapidly with increasing distance from pile. The excess pore water pressure became negligible at 15 pile diameters from the pile. Their results also showed that lateral displacement of the ground decreased with increasing distance from the pile. Pestana et al. (2002) carried out full-scale closed ended pile tests in the Young Bay Mud deposit. Higher excess pore pressures were observed for points closer to the pile, which decreased with increasing distance from the pile wall. Exponential decay of excess pore pressure with time was also noted. An 80% dissipation of excess pore pressure was achieved for soils more than one pile diameter away from the pile wall between 50 to 80 days. Lateral deformation generally decreased with increasing distance from pile wall, whilst varying erratically with depth. Bozozuk et al. (1978) reported on soil disturbance due to driving of 116 concrete piles in sensitive marine clays in a construction project. Maximum pore water pressures after pile driving within the group, and 6m (20 pile diameters) from the group were over 35-40% of the total overburden pressures, and the influence of pile driving on pore water pressure at 20m away from the group was very small. Cooke and Price (1973) studied a 168-mm-diameter instrumented pile jacked into over consolidated London clay. Outward lateral displacements ranging"

Jan 1, 2016

By Ryan Law

Ground energy systems are being installed in increasing numbers in the United Kingdom. This is particularly true in London where planning regulations require larger scale developments to provide at least 10% of their entire energy demands from renewable sources. A common approach has been to use the groundwater from the Chalk aquifer as a source of energy. This paper explains the potential long and short term sustainability problems with groundwater based systems sited in central London (or any other urbanized area). It also outlines an approach to site testing and numerical modelling to ensure that the system functions well throughout its lifetime. This approach is then applied to a project located in central London.

Jan 1, 2008

Workers in underground stone mines have a high fatality rate caused by falls of ground from the mine roof or rib. NIOSH recommendations to reduce ground fall injuries and deaths address baskets, mechanical scalers, mechanical bolters, drill steel changing, personal protective equipment, and training. Description of Exposure An informal National Institute for Occupational Safety and Health (NIOSH) review in 1998 identified approximately 17 new underground limestone operations in vari¬ous stages of planning; as many as 35 new underground stone mines are expected by 2005. Many of these new underground stone mines will employ new or inexperienced workers with minimal knowledge of the hazardous conditions that exist underground. Workers in underground stone mines have a fatality rate nearly 20 times that of workers in the manufacturing sector. Three quarters of the fatalities in underground stone mines are caused by falls of ground from the mine roof or rib (Figure 1) [Statistical Abstract of the United States 1985-1999; MSHA 1983-1999]. During 1983-1999, nonfatal ground falls resulted in 140 injuries, or 15% of all underground, lost time stone mine injuries. These nonfatal ground fall injuries resulted in more than 13,800 lost workdays (one third of all lost workdays). Ground falls generate more disabling injuries and time away from work than any other type of incident. [ ]

Jan 11, 2003