Search Documents

The EMEM Awards of the Department of Minerals and Energy (DME) were formally launched on 3 March 2000 by Ms Susan Shabangu, Deputy Minister at the Department?s Mineralia Centre in Pretoria. The launch was attended by invited guests from the mining and aggregate industries ,representatives of the Patron Organisations (see below),non- government and scientific organizations, the media, other government departments involved with mining environmental management and members of staff of the DME both nationally and regionally.

Jan 1, 2000

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increased usage for acid mine drainage mitigation and abatement as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulphurization byproducts from Virginia Electric?s Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1999

Despite the media's use of the mining industry as a whipping boy over its perceived attitude towards the environment, the facts remain that the only legislated requirement in the SA Statute Books for any form of environmental impact-assessment prior to development is to be found in the Minerals Act in the form of an EMPR. Not only is our industry complying with this requirement, but moves are afoot to set up environmental management systems for existing operations in preparation for seeking accreditation under ISO 14001 when published towards the end of this year. On how broad a front are we advancing? ? Is the industry equipped to handle these challenges? ? Does it have the determination to overcome its problems? ? Do we realise that failure may mean the loss of markets overseas to competitors who can meet the international standards? ? Where are the shortcomings and when must our efforts be focussed?

Jan 1, 1996

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By William Greenawalt

The Greenawalt electrolytic copper extraction process is applicable to suitable oxide ores, sulfide ores and concentrates, and low-grade matte. The process is self-sustaining in acid on sulfide ores or concentrates, on mixed ores, on high-grade oxidized ores; and on low-grade oxidized ores the amount of acid to be purchased or manufactured is greatly reduced. The ferric iron is under easy control, and copper may be effectively deposited from solutions of any acid or iron content likely to be used in copper leaching. From 60 to 75 per cent. of the copper may be removed from the solution in passing through the electrolytic department, before returning the solution to the ore. The amount of copper requiring chemical precipitation, from the waste and foul solutions, is only about 5.0 per cent, of the total copper produced, and this 5.0 per cent. is converted into the electrolytic metal in the regular operation of the process. The entire process can be made practically automatic, and can be carried out mechanically. There is no uncertain departure of any kind in the application of the process; no unusual or unproved apparatus is used. EVER since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydro-electric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods.

Jan 1, 1924

INCREASE OF CATASTROPHE FREQUENCY AND SEVERITYIn the last couple of decades the frequency of natural catastrophes has increased dramatically. This realization results from the statistical analysis of the comprehensive loss data that we have been collecting constantly over the last 30 years and have evaluated in connec-tion with the preparation of our "World Map of Natural Hazards", which is now in its second edition (Munich Re, 1988). Each month brings data on between 30 and 50 new loss events. Fortunately, however, only a few of these have to be added to the list of major natural catastrophes, that is only those involv-ing damage that considerably exceeds what the country or region concerned can handle itself so that substantial na-tional or international aid is required. That is generally the case if the number of dead runs into the hundreds or thousands, if tens or hundreds of thousands of people are rendered home-less and if the total economic loss is in the region of US$ 100 million. These major catastrophes, about which we have fairly comprehensive data even in the case of those that occurred farther back in the past, numbered only 14 in the 1960s but 70 in the 1980s; they there-fore increased over a period of 30 years by a factor of 5. The trend is also very clear when we consider the total economic loss, which - adjusted for in-flation - increased during the same period from an average of US$ 3.7 bil-lion per year to US$ 11.4 billion, i.e. by a factor of 3.1. The insured losses, finally, increased by as much as a fac-tor of 4.8.

Jan 1, 1990

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By David Clarry

?The issue ?reduction requirement ?Planning abatement steps ?Energy Management & Energy Efficiency ?Energy Recovery / Utilization ?Alternative Energy Professional Services Overview ?Capital Projects and Construction ?Project Development and Planning ?Engineering ?Project management ?Construction management ?Consulting ?Process ?Business ?Environmental ?Technology ?Operational Services ?In-house engineering services for operations

May 1, 2009

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

Deposits of the Reefton Goldfield, West Coast, New Zealand, are hosted on N-NE striking, upright folds of the Greenland Group. High-grade quartz lodes are hosted on axial planar shears, typically have short strike lengths, and form shoots that pitch steeply on the hosting shears. Deposits within the field area of a detailed structural study share these characteristics. Field mapping and microstructural analysis have demonstrated that the Greenland Group was affected by a multideformational sequence. Gold mineralisation is hosted on shears axial planar to the F2 folds, but occurred during a subsequent deformation event (D4). Deformation during D4 resulted from N-NE directed shortening, near parallel to the trend of the F2 folds. This event produced F4 kink folds that were accommodated by layer parallel slip on S2 parallel shears, gold mineralisation during D4 being confined to the dilational hinges of F4 kink folds. The semi-brittle nature of D4 allowed the formation of stockwork veining and disseminated mineralisation within the F4 hinge zones. Most deposits within the goldfield are similar to those within the field area, and are interpreted to have been mineralised during D4. The two largest known deposits within the goldfield, however, are distinct. The Blackwater Deposit, striking parallel to the hosting folds, has a combined strike length of 1 km. The Globe-Progress Deposit is hosted on an E-W striking discordant shear in which a brittle zone of disseminated mineralisation encompasses high-grade quartz lodes. The characteristics that distiguish the Globe and Blackwater deposits may be due to formation before and after D4 respectively. Detailed field mapping in the vicinity of known deposits throughout the goldfield will further refine the relationships between the F2 folds, later deformations and the localisation of ore deposits. Additional mapping may also help constrain the position, orientation and extent of additional orebodies.

Jan 1, 2001

By Louis W. Cope

Many Americans have seen Greenland while flying over it on their way to or from Europe. Few have visited this largest island in the world. Portions of the 20 percent of the territory that are not ice-covered are highly mineralized. Greenland could become very productive if the present interest in exploration increases. The people and Greenland’s history The population of Greenland is 57,000. Twenty percent are Europeans, mainly of Danish decent, while 80percent are native Greenlandic or mixed Greenlandic-European. The native population is the same as the Inuit of the Canadian Arctic. They speak the same language.

Jan 1, 2004

By Jose M. Milian, Raphael F. Matson

An intensive study was started in 1968 to determine the most economical process for winning nickel and cobalt from an extensive de- posit of complex, low grade nickel-cobalt ore (1.6% Ni, 0.10% CO) designated "the Greenvale ore." In 1974 the commercial plant at Yabulu, in Queensland, Australia, began processing the ore. In the interim, a great deal of laboratory and pilot-plant effort was applied to develop technical, process and commercial design data to demonstrate to potential financial backers and customers that a full-scale plant was feasible. The laboratory test work, pilot plant facilities and pro- gram are briefly reviewed in this paper.

Jan 1, 1979

By Takeshi Shinohara

It is a great honor and pleasure for me as President of the Japanese Tunnel Association to send greetings to the 1974 Rapid Excavation and Tunneling Conference. Recently in Japan, the Japanese Tunnel Association was established as recommended by the OECD Advisory Conference on Tunneling. This is a central organization concerned with tunnel construction consisting of government authorities, universities' research institutes and construction firms as well as manufacturers of relevant materials and equipment. As I was chosen the first president of the newly-established Japanese Tunnel Association, I would like to avail myself of this opportunity to announce to you its establishment and its earnest wish to contribute to the development of tunneling technique not only in our country but also all over the world. At the same time, I cordially request your friendship and cooperation for the benefit of further development of tunneling techniques on both sides of the Pacific. At present, many tunnels are under construction in Japan. The total length of tunnels under construction for railways and highways is about 600km including the 54km Seikan Undersea Tunnel which connects the Main Island and Hokkaido. Naturally, for construction of such tunnels in Japan, we have introduced much equipment and technique from the United States and other foreign countries. Now with accumulated experience, we are confident to be able to furnish various useful information concerning tunnel construction.

Jan 1, 1974

By Moto Goto

PT Smelting, located in Gresik, East Java, is the first copper smelter and refinery in Indonesia. Since the first charging concentrate in December 1998, many equipment troubles have been systematically eliminated, and the present operation is smooth and has accomplished the design capacity of 200,000 tonnes per year of LME, grade-A copper cathode. This paper describes troubles and countermeasures, which were experienced until now.

Jan 1, 2002

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989. Previous drilling indicated over 100 million cubic metres of gravels with some 90 per cent of the gold in the bottom seven metres. The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below. Metallurgical studies and exploration were initiated when the project commenced. Leasing and environmental considerations were investigated and action taken. While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989.Previous drilling indicated over 100 million cubic metres of gravels with some 90% of the gold in the bottom 7 metres.The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below.Metallurgical studies and exploration were initiated when the project commenced; Leasing and environmental considerations were investigated and action taken.While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

By M Simpson

Greywackes of the greater Auckland Region (Brynderwyn Hills to Hamilton), when considered on a regional scale, have characteristic ranges of physical, mineralogical and other properties. Some properties (eg density, porosity, crushing resistance, clay index) generally cluster and correlate with the basement greywacke facies, regions and terranes recognised by geologists, and their diagenetic/metamorphic level. Other local factors, particularly variations in mineralogical composition, nature of matrix cement, grain size, and degree of weathering may produce aberrant properties. Some of these local variations, when extreme, have the potential to affect the aggregateÆs performance in roading or the concrete industries.   Smectite and the zeolite laumontite are the major deleterious minerals occurring in fresh greywacke rocks of the Auckland region, although weathered rocks may contain halloysite, an expanding member of the kaolin clay mineral group. These minerals, when found in abnormally high levels in greywackes cause expansion effects in the aggregate. Currently there are inconsistencies in the detailed correlation of shrinkage, clay index, clay mineral content and intrinsic expansion data that need further research to resolve them.  

Jan 1, 2007

By Masaki Kitazume

"Many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction which occur in a loose and saturated sand layer, induces quite large damages of infrastructures, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Many kinds of ground improvement techniques based on various improvement principles have been developed for earthquake disaster mitigation. Among them, the grid type deep mixing method has been often applied to liquefaction mitigation. In the method, the stiff grid walls are constructed by mixing the soil and binder in-situ, which are expected to restrict the shear deformation of the soil within the grid walls so that the pore water pressure generation can be remained small. The high applicability of the method was confirmed in several earthquakes, including the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake. In this paper, the development of the method, some applications of the deep mixing method to earthquake disaster mitigation are briefly introduced. INTRODUCTION In Japan, many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction induces quite large damages, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Table 1 shows the amount of damage to port facilities (Noda, 1991). According to the table, the amount of damage when liquefaction takes place is about 20 to 50 times larger than that without liquefaction. This highlights the importance of liquefaction mitigation to minimize earthquake disasters. There are many kinds of soil stabilization techniques developed for liquefaction in Japan. Among them, the deep mixing method (DMM), an in-situ cement stabilization techniques, was developed in 1970s in Japan and has frequently been applied to improvements of clayey and sandy soils (Kitazume and Terashi, 2013). The grid type DMM has been often applied to prevent liquefaction, where the grid of stabilized column walls function to restrict generation of excess pore pressure in the soil within the walls by confining the soil particle movement. The improvement effect of the method was first evaluated in the Hyogoken-Nambu earthquake in 1995 and was also evaluated in the Tohoku earthquake in 2011. In this paper, some successful performance of the deep mixing method to earthquake disaster mitigation in the two earthquakes are briefly introduced."

Jan 1, 2015

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014