Search Documents

By Richard F. Link, George S. Koch

Advantages and disadvantages of deflecting (wedging) diamond-drill holes to obtain sampling data are compared with the alternative of drilling additional holes. The discussion is based on a statistical analysis of a large set of deflection data from exploratory boreholes in South African gold mines. Representative cost comparisons show the conditions under which deflections are likely to be desirable.

Jan 1, 1969

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968

By R Millar

A frequent challenge in mine water management and mine design is estimation of precipitation and extreme rainfall given a short record of site meteorological data. For remote mine projects, typically only a few years of rainfall data are available, which is far too short for estimation of design rainfall event, such as the 1-in-100 year storm. A frequency-paired approach is presented for comparing daily precipitation records from a mine site with a long-term regional station and provides the basis to transpose the long-term record to the mine site. This allows a long-term synthetic precipitation record to be developed for the mine site that can be used to undertake site water balance studies, determine pond storage requirements, assess water supply options and address other surface water management issues. Conventional approaches are based on chronologically-paired data and when applied to daily data generally yield poor correlations between stations. In the frequency-pairing approach, statistical distributions (two-parameter gamma distribution) are fit to daily data from two stations and used to calculate daily and extreme precipitation values for the short-term site (which is typically a mine or other project site). The method is demonstrated using data from two meteorological stations located along the south coast of British Columbia, Canada. Use of a fitted two-parameter gamma distribution (or other distribution) provides a sound theoretical approach to comparing precipitation data from two sites and the basis for transposing a long-term record to generate synthetic precipitation series and extreme rainfall values at mine sites.CITATION:Millar, R, 2013. A statistical approach for deriving project design rainfall, in Proceedings Water in Mining 2013 , pp 273-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By Beck RW, Booth GW

Differences in the gold contents of sub-sample duplicates, derived from a single bulk sample are a function of analytical and random error, inhomogeneity within the bulk and natural variations in the distribution of particluate gold. By minimising bulk sample inhomogeneity and determining analytical precision, the residual natural variation may be modelled statistically to give an estimate of Bold particle sizes.

Jan 1, 1989

By D. C. Krige

The estimation of the tonnage and grade of payable ore in a mine and the correct policy of selective mining based on such estimates, is of vital importance to the mining engineer it is surprising, therefore, that more attention has not been devoted on the Witwatersrand to the scientific improvement of mine valuation methods. At present these methods consist almost entirely of the application of simple arithmetic and empirical formulae guided by practical experience, and ignore the many advantages to be gained from a careful statistical analysis of the behaviour of the gold values. The science of statistics has expanded rapidly during the last two decades and its value as a powerful and indispensable tool is now recognized not only by research workers and scientists but also, ever-increasingly, by the commercial and industrial world. This being the case it is noteworthy that in a mining field such as the Rand with its highly developed and advanced mining methods, singularly little attention has been paid to the analysis of mine valuation problems on a modern statistical basis. This omission is even more striking when cognizance is taken of the wealth of sampling data concerning the gold ore which is available and of the far-reaching decisions and deductions constantly being based on such data. Some contributions have however been made from time to time towards the application of statistics to mine valuation on the Rand (References Nos. 7, 8, 9, 11, and 12), but none of these have been generally applied in practice and a systematic practical approach based on clearly deemed fundamental concepts still appears to be lacking. The object of this paper is, therefore, to define these statistical concepts and to indicate briefly the lines along which statistical methods can be applied profitability in solving some of the existing problems and in improving the general standard of mine valuation on the Rand For this purpose a knowledge of mathematical statistics is essential, but as this paper is primarily intended to provide the mine valuator with a practical introduction to statistical application in his field, the mathematics is confined to a short annexure, together with references from which details can be obtained.

Jan 1, 1994

By S. Sarac

In this study, a statistical model is suggested in order to determine the methane emission from a working seam. In the proposed method, methane concentrations which are systematically measured in return airway are the sample values, and the calculated statistical parameter is the upper confidence limit of the average of these values. At any given time, the probability of methane concentration in the return airflow to be lower than the calculated upper confidence limit value is 97.5%. The statistical method has been applied to the panel 206 of Armutcuk Mine, Turkish Hardcoal Enterprises. The calculated methane emission value for the considered shift was 15.18 m3/t.

Jan 1, 2003

By J. M. Mutmansky

A number of previous publications have attempted to provide the practicing ventilation engineer with simple guidelines on the optimal velocity to be used in mine openings. Some of these velocities were meant to be used in metal mining operations and some were meant for coal mining. A careful review of these publications reveals that the optimal velocities were determined based upon assumptions that are not existent today. As a result, they are not suitable for use in a modern coal mine. This paper takes a new look at this problem and determines a statistical relationship for optimal velocity that can be applied under both current and future conditions. The analysis performed here is based upon the determination of the optimal velocity for coal mine entries under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. A total of 8400 different conditions were analyzed for optimal velocity using computer calculation of the capital and operating cost values. Using the individual values of the optimal velocity derived in the calculations, a linear regression equation was fitted to the data to relate the optimal velocity to the other six variables outlined above. This regression relationship allows the ventilation engineer to make an easy, rapid determination of the optimal velocity.

Jan 1, 1984

By B. Amadei, A. Squassabia

This paper introduces the Rock Mass Median (RMM) index, a statistical measure of the mechanical quality of a rock mass thus is obtained through a mechanistic interpretation of the Poisson stochastic process. This process is the theoretical foundation of the Exponential Model, a probability distribution successfully used in practice to describe the spacing of discontinuities in rocks. Building on the Exponential Model, a simple method to compute RMM based on a widely accepted mechanical quality index is also presented. Verification is per formed through the analysis of two sets of core samples. Hypothesis testing at the 5% level of significance supports the validity of RMM for these samples.

Jan 1, 1994

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By Friedrich Wellmer

INTRODUCTION The Ramsbeck Pb/Zn Mine is located in the northern Sauerland area of West Germany, 150 km N of Frankfurt and 120 km E of Cologne. This is a vein deposit which has been worked from the middle of the 19th century to 1974. About 15 million tons of ore were mined and milled. The ore district contains several vein deposits and is roughly 14 km in length and 4 to 5 km in width. The host rocks are strata of Lower Middle Devonian age. The strata strike 60° to 70° NE and where overturned have a dip steeper than the veins (Fig. 1). The galena-sphalerite mineralization is in quartz veins, which are mineralized where they cut the "Main Ramsbeck Quartzite" horizon, a very competent host rock. Vein structures strike at 65º to 75º, dip about 20° to 25º SE and cut the quartzite at approximately 60 m intervals. The main or "steep veins" within each vein structure dip at 10º to 80° SE with an average of 30° and are offset by thrust faults dipping 5º N to 40° S with an average of 5º S. "Flat veins" usually weakly mineralized occur in the thrust faults between the "steep veins", thus forming the overall step-like vein structure. The mineralization is very irregular and changes a- long strike and down dip. It consists of thin veins of pure sphalerite and galena with quartz and pyrite. The thicknesses of the pure sphalerite and galena veins

Jan 1, 1977

By T. M. Yegulalp

One of the important factors affecting the determination of the minimum number of increments in a gross sample of coal is the variance component due to segregation. The segregation variance may be estimated by following the ASTM standard procedures. Since the estimate itself is a random variable, it is important to test if the value obtained is due to chance causes. This paper introduces a statistical test, based on the procedures published by ASTM, to test if the segregation variance is significantly greater than zero.

Jan 1, 1986

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By Hayward B. Oblad

The effects of eight independent variables on froth flotation product yield, ash content, and coal recovery were studied using laboratory batch flotation of 0.6 am x 0 coal. The eight flotation variables investigated were air feed rate, pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, collector conditioning time, frother (methyl isobutyl carbinol) concentration, and collector (No. 2 fuel oil) dosage. The two-level Plackett-Burman screening design and the three-level Box-Behnken design were used. Within the ranges studied, air feed rate had no effect on product yield. Pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, and collector conditioning time showed only minor effects on the product yield and quality. Frother concentration (mg/L) in the process water and collector oil dosage (g/kg) were shown to be the dominant independent variables in coal froth flotation. Flotation experiments that vary initial solids concentration at constant frother dosage (g/kg) confound the effects of frother concentration (mg/L) and solids concentration. The dominating effects of frother concentration and oil dosage on coal recovery and froth product ash content are illustrated with three-dimensional plots. The relationship between froth product ash and coal recovery is also clearly illustrated by the flotation data.

Jan 1, 1985

By W. P. Barnett

In 1988, the U.S. Department of Energy's Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation, and advanced cycloning. Each technology relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. Research projects designed to expeditiously develop each of these technologies to the point of commercial viability were initiated. This paper will present the status of these projects and the application potential of each technology to coal beneficiation.

Jan 1, 1992

By B. Erik Ydstie, Dimitrios I. Gerogiorgis, Sridhar S. Seetharaman

"Carbothermic production of aluminium is an important alternative to electrolytic processes and has in fact been identified several decades ago as a potentially feasible and profitable process. The cornerstone principle is to take advantage of the endothermic reduction reaction between carbon and alumina instead of resorting to extreme amounts of electric energy to ionize and reduce aluminium oxide to aluminium. Electric energy is necessary only for heating purposes.The present study focuses on constructing and solving a steady-state electrothermic model for obtaining the spatial distributions for electric potential, electric field intensity and temperature. The complex issues of reaction kinetics and multiphase flow are handled by an approximation and are not addressed at the present stage, due to the lack of complete validated models. Because of its inherent complexity, the reaction slag is considered a pseudohomogeneous layer.An electrothermic simulation encompasses important research challenges, due to the limited knowledge of thermophysical properties for high-temperature multi component molten slags. Therefore, thermophysical property modeling and a systematic compilation of published data is a necessary and major first step towards enhancing understanding of the process fundamentals. Models are obtained by analyzing measurement data from numerous literature references for the density, viscosity, thermal and electrical conductivity and specific heat capacity of the slag.The electric potential, field intensity and temperature distributions obtained reveal interesting maxima which indicate localized superheating and lead to important engineering conclusions. The temperature profile calculated will serve as the foundation for the flow problem solution. This computational study will form a basis for future research towards combining the scopes of microscale CFD modeling and mesoscale process modeling into a unified modeling approach."

Jan 1, 2001

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By G. W. Cutting

It is well known in both the research field and in commercial flotation processes that the grades and recoveries obtained from flotation plants are heavily influenced by the structure and height of the froths produced in the flotation cells. The development of steady-state mathematical models of flotation processes based upon practical and readily obtained parameters have demanded detailed information about the structure of flotation froths. The important parameters are the distribution of floating values, gangue and water in the froth with respect to froth height, cell pulp density, cell air flow rates and flotation inducing additives. Little work has been conducted in this field although considerable attention has been paid to bubble loading and other factors close to the cell froth/pulp interface. Laboratory batch tests are prefaced for the derivation of the above mentioned parameters for both practical and economic reasons. The standard laboratory flotation tests using a batch cell produces a froth of low height (1 to 3 cms generally) together with a varying cell pulp density as the test progresses due to the addition of top up water and the removal of froth from the cell. This form of test can be considered only as giving information about froth conditions close to the cell froth/pulp interface under conditions of widely varying cell pulp densities. In commercial processes the froth heights are much larger (frequently greater than 10 cms); therefore the laboratory batch test, although useful in many ways, does not directly yield parameters relating the state of the froth flowing over the cell lip to process operating conditions. To investigate flotation conditions, where more realistic froth heights are developed, an equilibrium type of batch cell has been developed at Warren Spring 1 Laboratory . In this a tank with high walls is used to contain the pulp and whole froth and, after a short period of operation, an equilibrium between froth

Jan 1, 1975

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By S. K. Kawatra, S. K. Valluri, S. J. Root

Common carbon dioxide capturing reagents, such as amines and sodium hydroxide, are expensive, toxic, and energy intensive to regenerate. We have added frothers to a sodium carbonate solution in order to increase the surface area available for CO2 transport within the packed bed of a counter current scrubbing column. Addition of frothers has improved the performance of sodium carbonate scrubbing solutions to be on par with sodium hydroxide scrubbing solutions. This novel enhancement of a relatively inexpensive CO2 capture-regeneration cycle shows potential to allow plants to turn a profit by sequestering a waste product. These results are discussed in detail in the following manuscript. INTRODUCTION The combustion of fossil fuels converts chemical energy to thermal energy. CO2 is produced as a byproduct of the reaction. 80% of the world’s electricity is produced by using this thermal energy to power a generator, accounting for 40% of global carbon dioxide emissions. In an effort to stabilize the rising atmospheric CO2 levels, researchers are investigating the application of carbon capture and storage (CCS) systems in power plants. [1] Efforts to capture CO2 at some power plants have been successful, but the cost of installing and operating the required equipment is high. As such, very few power plants have CCS systems. If CO2 can be captured and processed into a product that can be sold at a profit, installing CCS systems in power plants will be a very attractive business decision. In order for the sale of captured CO2 to become a profitable venture, the cost of capturing the CO2 from a flue gas must be reduced. BACKGROUND The most common method for separating CO2 from a flue gas is by passing it through a counter-current packed bed scrubbing column. The flue gas enters the bottom of a column while a solution of a chemical with properties advantageous to the absorption of CO2 is pumped to the top. The fluids interact in a packed bed, where the CO2 is transported from the gas to the liquid. CO2 is an acid gas, so it is common for the scrubbing solution to be alkaline in nature in order to neutralize the carbonic acid that is formed when it is dissolves into water. The exhaust exits the top of the column free of carbon dioxide, which exits the column in the scrubbing solution, reacting or complexing with the absorbent. Figure 1 is a schematic drawing of a CO2 scrubbing column. It shows the molar flowrates and compositions of the gas and liquid at the bottom [1], the top [2], and an arbitrary height in the column [Z]. [2,15] L is the molar flowrate of liquid at any point in in the column. G is the molar flowrate of gas at any point in the column. Since the CO2 is transported from the gas to the liquid, L and G are variable with respect to height. To simplify calculations, the CO2 free molar flowrates Ls and Gs are often used. X is the fraction moles of aqueous CO2 per mole of CO2 free liquid. Y is the fraction moles of gaseous CO2 per mole of CO2 free gas. Figure 2 is a composition diagram of the scrubbing column depicted in figure 1.

Jan 1, 2019