Search Documents

By Alexandre Silva Guimarães

A extração por solventes sinérgica dos metais cálcio, magnésio e níquel, presentes em soluções aquosas sulfúricas em níveis de concentração similares aos dos licores industriais HPAL (High Pressure Acid Leaching), foi avaliada neste trabalho empregando-se os extratantes comerciais Cyanex 272 e Cyanex 301. O uso de Cyanex 301 (10%v/v) sozinho não se mostrou eficiente, em decorrência do baixo percentual de extração e da baixa seletividade entre os metais. Quando misturado ao Cyanex 272, porém, observou-se a possibilidade de remoção seletiva de magnésio, deixando cálcio e níquel em solução. A melhor condição operacional foi obtida utilizando-se 5-10%v/v de Cyanex 301 e 20% de Cyanex 272, na faixa de pH entre 5,4-5,7, na qual se extraiu aproximadamente 70-80% de magnésio, 15-35% de cálcio e 10-15% de níquel.

Aug 16, 2017

By Alexandre Silva Guimarães

Investigou-se a extração seletiva de Ca e Mg do licor sulfúrico concentrado de Ni visando sua purificação. Observou-se que a mistura sinérgica dos extratantes D2EHPA + ácido naftênico apresenta maior afinidade na extração de Ca em pH = 5. Comportamento oposto foi verificado pelo extratante Cyanex 272, cuja preferência de extração é pelo Mg para 5 = pH = 6. A cinética de extração de Ca e Mg é rápida atingindo o equilíbrio em menos de 6 minutos. A purificação do licor de Ni requer a utilização de 2 circuitos de extração em operações estagiadas. No primeiro circuito, Ca pode ser removido do licor empregando-se o sistema orgânico D2EHPA (10% v/v) + ácido naftênico (20% v/v). O pH ótimo é 3,5, no qual foram extraídos 72% de Ca (ßCa/Ni = 40) em uma contatação. No segundo circuito, o licor deve ser submetido a uma extração de Mg pelo Cyanex 272 (20% v/v). O pH operacional propício é 5,5 com extração de 66% de Mg (ßMg/Ni = 16, uma contatação). O licor purificado de Ni pode ser encaminhado à etapa de eletrorrecuperação almejando-se a obtenção de Ni metálico.

Oct 30, 2017

By Carlos de F. Gontijo

The flotation of quartz particles was studied over the particle size range from 0.5 µm to 1000 µm and for advancing water contact angles between 0º and 83º. Flotation was performed in a column and in a Rushton turbine cell. Particle contact angle threshold values, below which the particles could not be floated, were identified for the particle size range 0.5~1000 µm, under different hydrodynamic conditions. The flotation response of the particles, either in a column or in a mechanically agitated cell with a similar bubble size, was comparable. Turbulence plays a role, as does bubble-particle aggregate velocity and bubble size. The stability of the bubble-particle aggregate controls the maximum floatable particle size of coarse particles. For fine particles, the flotation limit is dictated by the energy required to rupture the intervening liquid film between the particle and bubble. Flotation of very fine and large particles is facilitated with small bubbles and high contact angles. These results greatly extend our earlier observations and theoretical predictions.

Jan 1, 2014

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By Alexander Malahoff

The study of why and how life survives in the Extreme environment is a major frontier of science today. Extremophiles are organisms that require extreme environment including high temperature, pH, pressure and salt concentration, or low temperature, pH, nutrient concentration, or water availability. Their common habitats are geothermal vents, pools, lakes and craters of active volcanic regions, such as those of New Zealand, Japan, Kamchatka, Yellowstone USA or the hydrothermal vents of the ocean ridges and submarine volcanoes. These settings are accessible by foot, boat, helicopter, or submersibles. This presentation examines the geology, chemistry of geothermal sites of New Zealand, including the active volcano, White Island, Yellowstone, the submarine volcano Loihi in Hawaii, and sections of the mid-ocean ridges. Designing process and construction of Extremophilic sampling and bioreactor systems used in the study of Extremophiles will be discussed. The driving force behind the research of extremophiles is not only the fundamental science, but also biotechnological potential associated with these microorganisms and their cellular products. The University of Hawaii?s Marine Bioproducts and Engineering Center (MarBEC) is laying the foundations for such new industries.

Jan 1, 2001

By Siegmund Babendererde, Jan O. Babendererde

Extruded Concrete Lining combines technological and financial advantages. The tunnel lining is reliably embedded in the surrounding ground as the fluid concrete is extruded at constant pressure directly behind the TBM supporting the exposed surface. Ground deformation from the TBM passage can be compensated and the ground will be pre-stressed by the extrusion process. Developments in concrete technology permit high speed tunneling by use of a slip formwork attached to the TBM. Realised projects in Milano (Italy), Lyon (France), Frankfurt (Germany) and Akima (Japan) will be demonstrated.

Jan 1, 2001

By D. S. Salonine

Aluminum alloys are widely used in modern industry. Tubes and hollow shapes give great opportunities for structural purposes as well as fluid transport due to their stiffness and lightness, Extrusions on a mandrel or through a bridge die, that requires splitting of the billet with re-welding, produce hollow shapes with varied contours, fins and multiple cavities. Moving and stationary mandrels, mandrel lubrication, tooling for ribbed-tube heat exchangers, and for drilling pipes are considered. Bridge dies can be classified by the bridge position relative to the die face, by mandrel support structure, and by assembly type, The main parameters influencing the quality of the die-welded seams are considered, The difficulties of extruding various alloys through bridge dies are discussed in terms of metallurgical factors, Some approaches to the calculation of the stresses in a bridge are presented.

Jan 1, 2005

By W. B. Price

AT the New York meeting of the American Institute of Mining-and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."§ The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. PROTUBERANCES ON ADMIRALTY BRASS In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig.. 1a) and upon analysis was found to contain 66.66 percent. copper, 4.02 per cent. tin and .03 . per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and .01 per cent. lead. A sample of the shaggy-rough protuberances at the -very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had -revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation."

Jan 10, 1926

By W. B. Price

AT the New York meeting of the American Institute of Mining and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."' The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. Protuberances on Admiralty Brass In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig. la) and upon analysis was found to contain 66.66 per cent. copper, 4.02 per cent. tin and 0.03 per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and 0.01 per cent. lead. A sample of the shaggy-rough protuberances at the very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation." Fig. 16 is a cross-section of a bar through the protuberances on the surface. It reveals that there is a decidedly different structure through the raised areas and seems to indicate that the bar originally solidified

Jan 1, 1927

By W. H. Bassett

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. It is suggested that the material is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the sheet. FIGURES 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this? paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent.

Jan 2, 1926

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982

By Humberto Ghersi

El presente texto señala los exámenes médicos pre-ocupacionales en la industria minera. Esta evaluación es el primer nexo entre el médico y el trabajador que sirve para percibir la condición física y psíquica del futuro operario y y luego destinarlo a una labor acorde con las cualidades encontradas. Las leyes peruanas que ordenan los exámenes médicos pre-ocupacionales están principalmente contenidas en el Reglamento de Seguridad e Higiene para la Industria minera y metalúrgica, las cuales obligan que todo el personal técnico, empleados y obreros y personal que labore en subsuelo y superficie cumpla con dicha disposición reglamentaria. El examen médico se detallára en la ficha médica del trabajador y determinará la capacidad del trabajador. La ficha médica debe incluir un control radiográfico y se debe conservar un archivo radiográfico del personal, como la mejor manera de evaluar los cambios que pueden operarse con el transcurso del tiempo.

Jul 20, 1961

By Stephen Hall

Introduction Marine Autonomous Systems are making rapid progress from their early years as research tools for university departments & government institutes into having a growing number of real-world applications for industry, academia, statutory inspection, data acquisition and defence. Deep sea mining offers a distinct set of challenges that are very well suited to autonomous underwater vehicles (AUVs) and to a lesser extent for autonomous surface vehicles. Deeper, smarter, more capable Global demand for rare earth metals and high-grade ore will inevitably lead to exploitation of deep ocean resources as terrestrial reserves become depleted or remain unavailable for political or environmental reasons. Winning production licenses from the international seabed authority and especially gaining public trust to undertake deep sea mining activities and licenses will depend upon high quality pre-exploitation scientific surveys of the sea floor ecosystem, and subsequent monitoring of the impact of mining activity and remediation work. The actual area covered by the seabed mining operation may be quite small in terms of square kilometres, but still larger than can be patrolled by tethered ‘eyeball’ class Remote Operated Vehicles, so multi-spectral inspection, assessment and monitoring will be more effective when carried out by untethered AUVs. By using seabed recharging stations and data upload points the AUV can stay in situ in the deep ocean, rather than be repeatedly brought back to the surface.

Jan 1, 2018

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By F. G. Cottrell

AS previously announced, Van. H. Manning has resigned as director of the Bureau of Mines, effective June 1, to become director of research with the newly organized American Petroleum Institute. Doctor Manning has been connected with the Department of the Interior for 34 years, having been civil engineer with the Geological Survey, from 1885 to 1910, previous to his connection with the Bureau of Mines which was organized in the latter year. Doctor Manning was appointed to an administrative position in the new Bureau under Joseph A. Holmes, its first director, and on Jan. 1, 1911, was made assistant director. On Jan. 1, 1914, when Doctor Holmes had to relinquish active

Jan 1, 1920

By H. Mogollón

El presente texto señala el proceso de fabricación del alambre y cobre en la Cerro de Pasco Corporation, así como los métodos adecuados para su elaboración. Bajo el amparo de la ley 13270 de promoción industrial nace la Compañía Industrial del Centro, subsidiaria de dicha corporación, y responsable no solo de la producción de barras y alambrón de cobre, sino de la producción de ácido sulfúrico en La Oroya. Actualmente, esta producción se ajusta a 90 toneladas métricas de alambrón redondo de cobre refinado con un diimetro nominal de 7,9375 mil metros. Sin embargo, esta pueda ampliarse hasta un máxlmo de 145 toneladas métricas a través de cambios menores en el equipo auxiliar.

Nov 20, 1967

By Vicente Martínez Guerra

Producto de una de las operaciones realizadas en la Cerro de Pasco Corporation, se obtienen algunos elementos y subproductos químicos como el arseniato de calcio que ocupa el primer lugar en ventas en dicha compañía. Por ello, el objeto del presente texto describe el proceso y el uso de As2 O3 para la fabricación del arseniato de calcio en la planta de fundición de La Oroya, como su aplicación de insecticidad mineral en la agricultura. Dentro de este periodo, el elemento químico será recuperado en el cottrell de arsémico, de los humos provenientes de los hornos tostadores de los minerales de cobre, precipitando una concentración oscilante entre 40 a 45% con un contenido de cobre de 4%. donde el polvo sufre una tostación para así concentrar el cobre por sublimación del arsénico. Asimismo en este sistema de fabricación de arseniato, la liberación del As2 O5 del piroarsenIato de calcio se realiza por ataque con ácido sulfúrico, garantizando la pureza de este óxido en la precipitación final del proceso. En consecuencia, la aplicación del arseniato de calcio, como insectida inorgánico mineral protege el sistema ecológico, dado su bajo contenido de arsénico soluble en agua, al tiempo que se ajusta a las reglamentos oficiale vigentes del país.

Jul 20, 1956

By Carlos Villachica León

El presente texto describe el proceso de obtención de oro y plata refinado, sin la utilización de mercurio ni cianuro a través de la tecnología desarrollada para la fabricación de fundente ecológico Biox. Esta tecnología implica la amalgamación, fundición con litargirio y copelación de minerales de oro y plata para la aplicación a concentrados auríferos de baja y alta ley en mineras de pequeña escala.

Jul 1, 2016

By V. I. Kefeli

Public-private partnership efforts are working to create green landscapes from abandoned industrial sites. Fabricated soils, potentially an essential element of such landscapes, are designed to substitute for topsoil on the areas free from ground cover and plant community. The aluminosilicate matrix and humus form the soil micelle - the primary unit of any soil complex. Humus formation is a process based on carbon-nitrogen interaction. Sources of carbon can be materials rich in easily composted products like cellulose and polyphenols (plant leaves) or aged lignin polymers (saw dust from different woody plants). The pathways of carbon-nitrogen complexes are discussed. Properties of the fabricated soil components were examined by bio-tests and plant models.

Jan 1, 2002