Search Documents

By CASSANDRA L. HOEBBEL, PATRICK L. YORIO, Emily J. Haas

This study revealed significantly less favorable perceptions of the existing organizational safety climate among workers in the underground coal-mining sector compared with those in the industrial-minerals and sand, stone and gravel (SSG) sectors. Consequently, it is important to consider pragmatic ways in which health and safety management systems (HSMS) in coal mines can alter processes to improve these perceptions. Given the interdependencies of safety climate factors and HSMS elements, researchers explored mineworker perceptions of the supportiveness of organizational safety climate factors among mineworkers and identified significant differences in perceptions across sectors. In this paper, we suggest that health and safety professionals in underground coal mining and organizations with fewer resources or less mature HSMSs focus on these factors to bolster support for proactive safety performance. Potential barriers to implementing or improving relevant HSMS elements and ideas to help foster more favorable perceptions of organizational safety climate are also discussed.

By Di Liu, Yongjun Peng

"It was identified that clay minerals adversely affect fine coal flotation through slime coatings. In the study, it was interesting to find that an anionic polymer dispersant, lignosulfonate, successfully mitigated the negative effect of clay minerals in coal flotation using fresh water, but in saline water, it exacerbated coal flotation.In order to understand the mechanisms underpinning the different behaviour of lignosulfonate in coal flotation using fresh and saline water, the adsorption isotherm, and dynamic light scattering (DLS) measurements were conducted in this study. While DLS monitored the molecular conformation change (swelling or shrinking) of the polymer in fresh and saline water, adsorption isotherms enabled polymer adsorbed amount on clay and coal mineral surfaces to be determined. It was found that lignosulfonate adsorbed on the coal and clay mineral surfaces providing effective electrostatic repulsions and resulting in a mitigation of clay minerals from coal surfaces in deionised water. In the presence of saline water, however, polymer molecular conformation changed. Polymer molecules were compressed and adsorbed in form of aggregates. The adsorption amount of lignosulfonate on clay minerals increased in saline water. A low dosage of lignosulfonate could not provide sufficient electrosteric repulsion to disperse clay minerals. Moreover, the high adsorption amount of the polymer on coal and clay surfaces led to a more hydrophilic coal surface, and coal flotation was therefore depressed in saline water. This study provides a new insight into understanding the role of anionic polymeric dispersants in mineral flotation using different quality water."

Jan 1, 2014

By Valery W, Morrell S, Loughlin P, O&apos

Traditionally, blasts in mining operations are designed to prepare the in situ rock mass for excavation and transport without much consideration being given to the downstream comminution processes. Blasting is in fact the first step in a chain

Jan 1, 1998

By Francisca San Martín, Martin Rudolph, Willy Kracht, Tomás Vargas

It has been shown that bacteria Acidithiobacillus ferrooxidans can be used to depress pyrite in seawater flotation at natural pH, which opens the possibility for its use as an alternative to lime to depress pyrite in copper sulfide flotation. In order to have a better understanding of the mechanisms involved in pyrite depression with A. ferrooxidans, an exploratory experimental campaign was carried out, including attachment density and contact angle measurements, and the effect of adding bacteria before or after collector. Biodepression of pyrite improves when increasing pH from 3 to 8, with a decrease in recovery from 92% to 36%. This increase in depressing capability is accompanied by an increase in attachment density, from 2.58×108 bacteria/g to 1.99×109 bacteria/g at pH 3 and 8, respectively, suggesting that the mechanism of depression is related to the attachment of bacteria to the pyrite surface. It was observed that the conditioning sequence with collector and bacteria influences the biodepression capacity of A. ferrooxidans. Having as a reference a value of pyrite recovery equal to 97%, when using only xanthate in seawater flotation at pH 8, the effect of both conditioning with bacteria-followed-by-xanthate and xanthate-followed-by-bacteria were assessed. When bacteria were added before the collector, the recovery of pyrite decreased to 36%. On the other hand, when bacteria were added after collector, the recovery was 64%, showing that biodepression of pyrite with Acidithiobacillus ferrooxidans is more efficient when the conditioning is carried out first with bacteria. The contact angle values show that there is little effect of the second component added to the system, i.e., if pyrite is first conditioned with bacteria, the contact angle does not change significantly once the xanthate is added (bacteria-followed-by-xanthate). The same was observed when the conditioning sequence was xanthate-followed-by-bacteria.

Jan 1, 2018

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By J. L. Broadhurst, S. Rumjeet, S. T. L Harrison, T. Chimbganda

Post-mining land use for the production of industrial crops has the potential to mitigate environmental and socio-economic impacts of mine closure and stimulate post-mining economic growth. Fibre-rich plants are of particular interest due to their multi-product potential. In the South African context, where there are many abandoned and end-of-life mines near human settlements, an opportunity presents to assess the feasibility of transforming post-mining land into productive land and building resilient communities through the development of multi-product value chains from fibre-rich plants such as kenaf, hemp or bamboo. This paper provides an overview of the plant selection criteria, phytoremediation potential and the downstream options for the recovery of products and value from bast fibre plants (hemp and kenaf) and bamboo. Based on findings from a comprehensive review of the published literature, as well as interviews with relevant experts within South Africa, it appears that bast fibre plants are the best downstream option for producing ‘green’ textiles and high-end niche products, whereas bamboo is more suitable as a replacement for conventional timber. Although fibre plants have the potential to extract metals from soils, high concentrations may inhibit plant growth and affect the quality of the final fibre product. Further site-specific studies would thus be required to select the best route for both land remediation and optimal product recovery. Keywords: Bioremediation, bamboo, kenaf, hemp, multi-product value chains, sustainable postmining land use

Jan 1, 2020

By Jacob Carr, Rebecca Knuth, Emily J. Haas, Marvin Cheng, Bob Bissonette

Many industries, including mining, are experiencing an increase in the use of robotic and other artificial intelligence (AI) systems to improve efficiency, productivity and precision. For example, a 2023 survey showed that mining industry executives wanted to integrate more autonomous equipment to improve productivity and alleviate workforce shortages (Haas, 2024). This feedback was coupled with an increased appetite to advance the types and uses of automation and AI in the workplace. However, there is also an increasing concern about the ways that robotic applications may unintentionally affect worker safety. Humanmachine interaction poses potential risks, especially when industrial robots operate near workers in specific environments (such as drilling, handling and transporting materials, equipment inspection and lifting heavy loads). Research has explored the unintended consequences of introducing new technologies or processes in the workplace to include incidents such as being struck by equipment and challenges around data privacy (Lööw et al., 2019; Khurram et al., 2025; Haas and DuCarme, 2015; Almeaibed et al., 2021; Zio and Miqueles, 2024). More recently, the use of digital twin technologies and simulations (hereafter referred to as digital twin systems) has been boasted as a tool that can help prevent unintended consequences around worker safety by identifying and mitigating risks before a worker completes a task in tandem with a robot or other new technology. Digital twin systems produce a virtual replica of a physical environment or process (Almeaibed et al., 2021; Zio and Miqueles, 2024; Saes, 2024). To this end, this article explores the potential role of digital twin systems in enhancing safety within mining and other similar environments. It will primarily focus on environments where robots and human workers may interact, although digital twin systems can be useful with other technology applications. First, we define digital twins and digital simulation as components of a system. Then, we highlight possible applications of digital twin systems in mining to replicate real-world processes, followed by potential benefits of their use and where more research may be needed.

Oct 1, 2025

By Raymond A. Binns

Drilling into an active hydrothermal system linked to convergent-margin felsic magmatism is a listed priority of the Ocean Drilling Program that addresses several fundamental geoscience issues. Solid and fluid products of felsic rock-water interaction, and the consequences for global chemical fluxes and for ore deposition, should differ from those in basaltic mid-ocean ridge environments already successfully tested by Legs 106, 139, 158 and 169. So, too, will fracturing controls on fluid pathways, and sources for metals and ligands. Researching the subsurface volcanic, structural/hydrologic, and mineralisation/alteration architecture of a drilled felsic-hosted system also has economic implications, especially for land¬based mineral exploration. A first-order hypothesis to be tested states that fluids derived from volatile-rich magmas are more important than recirculated seawater in convergent-margin hydrothermal systems - economic geologists increasingly appeal to this for creating "world-class" massive sulfide orebodies. Another hypothesis proposes "subhalative" massive sulfide deposition within hydraulically expanded volcanic products as a factor in generating large orebodies. Many second-order hypotheses such as leaching fractionated volcanics to cause gold enrichment in back¬arc systems also need testing. The thoroughly surveyed, active, PACMANUS hydrothermal field in the Eastern Manus back-arc basin of Papua New Guinea will be the site for ODP Leg 193 commencing in November 2000. It lies near the crest (1655-1750 m) of high-standing Pual Ridge, a 40 km-long edifice of dacite/rhyodacite with basal andesite all having geochemical and isotopic affinities with modern arc volcanoes of nearby New Britain. PACMANUS includes at least three focussed, high-temperature "smoker" sites with Cu+Au-rich massive sulfide deposits, and a field of diffuse, lower temperature venting through intensely altered dacite where modelling indicates significant subsurface mineralisation. Isotopic characteristics of deposits and vent fluids suggest magmatic contributions to the mineralising fluids.

Jan 1, 2000

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002

By K. C. Corin, M. Tadie, R. M. Manenzhe

The near depletion of high-grade ores, among other factors, has necessitated the consideration of alternative PGM sources. Various factors in the metallurgical processing of ores result in valuable minerals being lost to the tailings, and hence, PGM tailings are a possible alternative PGM source. However, as the value residing in PGM tailings remains unquantified and uncharacterised, there is a challenge in knowing the recoverable fraction of value contained in PGM wastes. This paper outlines the in-situ techniques of oxygen uptake and EDTA extraction for their possible use for determining the recoverable value in PGM tailings. Both methods have shown efficiency in determining the weathering of sulphide minerals and sulphide-bearing ores. Keywords: PGM tailings, tailing retreatment, oxidation, oxygen decay, EDTA

Jan 1, 2020

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2017

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2018

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

Researchers examined datasets from two separate studies that measured common demographic variables but different safety performance outcome variables. Of specific interest was how types of experience might relate to workers’ preparedness to effectively mitigate or respond to both routine and nonroutine risk in the mining industry. The results suggest that individual factors such as length of job, industry, and mine experience are predictive of routine safety performance — as measured by self-reported proactive and compliant safety behaviors — and/or nonroutine safety performance — as measured by perceived competence in self-escape knowledge, skills and abilities (KSAs) — in significant and sometimes unexpected ways.

By Jensen B

The investigation of the explosion characteristics of nine Bowen Basin (Central Queensland) dust samples in a suitable coal dust explosion chamber using a new dust concentration probe provides several advances in the area of coal dust explosibility testing. The 20 litre explosion chamber, of novel design, uses rotation of the main body of the chamber together with air jets for dust dispersion, and allows testing of different types of explosion initiators and analysis of the explosion characteristics of coal dust/methane mixtures of varying concentrations.A new development was a dielectric dust probe for the measurement of coal dust concentration. A capacitive micrometry technique was successfully adapted to measure dust concentration. The system uses a ratio-transformer bridge for measurement of small changes in a capacitive probe designed to sample a representative volume. The device is accurate, and is capable of operating in the hostile environment within the explosion chamber.The explosion chamber and dust probe characterise the explosive potential of coal dust samples by determination of the dust lean limit concentration in varying mixture with methane. Plots of lean limit points obtained in this way present an explosion curve for each sample which indicates the potential of the coal dust/methane to explode under the conditions of initiation in the chamber. The explosion curve obtained for each sample presents a unique signature that appears to reflect the physical and chemical characteristics of the dust.The results from this series of laboratory experiments appear to provide a useful index and indicate potential areas of interest for future research.

Jan 1, 1991

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By W. H. Moore

It seems necessary, at times, that we should reconsider some of the more obscure causes that lead to explosions of gas and coal-dust in mines, in the hope that a recapitulation will keep before us that old and true saying "eternal vigilance is the price of safety". This explosion, while not extensive (resulting in only two much to be regretted deaths) enlarged our vision as to the possibility and probability of other explosions with more disastrous results. As this is only a partial report I shall have to omit many things that are generally included in describing a mine explosion. The mine was worked exclusively with electric cap-lamps -only firebosses and other officials carried safety-lamps. All shots were examined and fired by firebosses with a small hand-battery. Monobel was used exclusively for blasting, and clay for tamping. The system of haulage iri use was main-rope and winches, horses being employed for gathering. Compressed-air was the motive power for all winches and pumps, excepting the pumps at the shaft-bottom which were steam-driven. The mine was wet with practically no dust anywhere, except what was being made at the coal-face in the getting of the coal. Gas was found occasionally, generally in the brushing, especially where the brushing was carried up to a small seam, 2 to 6 feet above the main seam. The place where the explosion took place was known as Leigh's heading, which was being driven to the rise, immediately inbye of the siding (off No. 1 left, off the new slope) and was about 90 feet up from the level.

Jan 1, 1926

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

By Roberto Folcht

The obligations of the European Directive 96/82/EC on the control of major accident hazards, the so-called Seveso II Directive, became mandatory within the E u ropean Member States February 3, 1999. Explosive products have been included within the Seveso II Directive, in the categories of substances capable of generating a major accident. In addition to taking “all measures necessary to prevent major accidents,” explosive manufacturers are also obliged “to limit their consequences for man and the environment.” However, for explosives in particular, no pro c e d u res, nor specific re f e rence values for damage calculation, are given either in the Directive or in the corresponding Italian Legislation, “Ministry of the Environment decree of 20 Oct. 1998.” This article presents a simplified but scientifically rigorous approach for the first approximation calculation of the effects on the surrounding area following an accidental explosion. As an example of the method of calculation, the damage areas in a hypothetical explosives manufacturing facility, as shown in F i g u re 1, will be anal y z e d . The method proposed in this article can also be used for the analysis of explosions of gas in tanks or pipelines,

Jan 1, 2004