Search Documents

By M. Faure

The experiment with backfill at Harmony was mainly an attempt to improve the ground conditions in a particularly tricky section of the mine. A deslimed tailings system was selected for financial reasons, ease of installation, ease of operation and its low level of mechanization. The design of the system has three aspects: firstly, to define the parameters of the backfill material itself; secondly, to design a reliable plant which could consistently produce the desired material in sufficient quantities; and, thirdly, to design a fill distribution system for maximum reliability in the shaft, minimum pipe line velocity, pressure and cost in the horizontal sections and consistency and reliability at the delivery end. The system was successfully constructed and commissioned in a short space of time at a relatively low cost. It has now reached its full potential, and very encouraging results have been achieved with regard to cost savings, ground conditions, ventilation and accident statistics.

Jan 1, 1988

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

THE Johnson award for 1926 was given to T. L. Joseph for his experimental work on blast-furnace operation. When the Bureau of Mines undertook its experimental blast-furnace investigation in 1919, a number of operators and metallurgists were doubtful as to the practicability of small-scale tests. Several pre-vious attempts, outside the Bureau, to operate small furnaces had been unsuccessful. However, pig iron was produced in three and four-ton furnaces during the first half of the nineteenth century. The operation of a small furnace did not therefore seem an impossible task. This point of view, together with a realization of the importance of problems connected with the pro-duction of pig iron, prompted the Bureau to undertake this work. Such problems as the feasibility of using charcoal briquets as a fuel, the application of oxygen enriched blast, and the use of new ores and raw ma-terials, in general, can be investigated only at consider-able cost on full sized furnaces, while with an experimental furnace they can be conducted at a com-paratively ;small, cost. The results of small-scale tests are sufficient to determine whether the problem. War-rants the expenditure required for a trial on a com-mercial scale. The accompanying photographs and chart show the various stages of the experimental furnace development. Some idea of the size and shape of furnaces which were tested can be had from the development chart. In oper-ating furnaces A to F, a series of changes were made to increase hearth temperature. Perhaps the most im-portant change was the position of the tuyeres with respect to the bottom of the hearth. The height of the tuyeres above the hearth was gradually increased and the hearth diameter decreased. It was shown by this series of furnaces that metal and slag are the chief source of heat supply to the crucible. For this reason there is a minimum rate at which these materials can be brought into the hearth of a small furnace if it is to function properly. The rate of slag "and metal fall are determined by the burden on the furnace and the rate of blowing. Due to lack of funds necessary to provide ample blowing equipment, hot blast stoves, essential mechani-cal features, and to meet operating expenses, it. was necessary to work with much smaller furnaces, such as G to K shown in the chart. The particular object of these tests was to study the extent to which reactions could be speeded up by decreasing the size of the stock. One decided change, noticed at the beginning of this series of tests, was the effect which coke size had on the production of a strongly reducing gas. Furnace G, 22 in. high, operating on coke crushed to pass 10 mesh, made a gas richer in carbon monoxide than did fur-naces A to F, operating on run-of-the-oven coke.

Jan 3, 1927

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By J. R. Katan, J. R. Ball, Peter R. Bannister, F. J. Williams

During the last week in March and the first week in April, 1973, the Naval Underwater Systems Center measured the 76 Hz magnetic field strength (in Wisconsin and Texas) produced by both the elevated and (newly installed) buried Wisconsin Test Facility (WTF) north-south (NS) antennas. The principle result obtained from these measurements is that there is no measurable difference in performance between the WTF buried and elevated NS antennas.

Jan 1, 1973

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

THE furnace described in this paper was installed and has been used by the writer for the melting of rich gold-bearing material, and has given complete satisfaction. It may, therefore, prove of interest to other metallurgists who are faced with a similarproblem. A furnace of this type should be most suitable for the reduction of "cyanide preeipitate," "charcoal ash," "anode sludge," &c. formerly the melting was done in fire-clay crucibles, using coke or crude oil as fuel, but this method is costly, slow, and unsatisfactory. A small water-jacketed blastfurnace was also tried on this material after briquetting it, but was discarded in favour of the electric furnace. The furnace may be described as a simple form of the Heroult resistance furnace, with an adjustable upper electrode and a fixed bottom electrode. This is in accordanee with Stansfield's classification of electric furnaces. The heating is mostly due to the resistance offered the current by the molten slag. The melting chamber consists of a steel drum 14 in. in diameter and 21 in. high, and is lined with silica bricks specially made to fit the shell. The internal diameter is G in. The bricks contain 92 % silica, are made from calcined quartzite bonded with fireclay, and are similar in composition to those used for lining steel converters. They are set in a mixture of finely-ground quartzite and clay, and well dried out. The shell is bolted to a steel plate, which forms the decking of a truck running on rails, so that the furnace can be moved under ahood for carrying off the fumes. A cast-iron slag spout is bolted to the shell below the tapping hole, which is 4 in. from the bottom of the shell. Opposite this another hole 1 in. in diameter is drilled through the shell and lining for the passage of the lower...

Jan 1, 1918

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By R. A. Campbell

Pig iron and silicospiegeleisen were produced experimentally from a very low-grade manganiferous iron ore from Steep Rock, Ontario, by a two-stage electric smelting process. The most favourruble operating conditions were determined for each stage. Cement clinker then was made by calcining the slag from the second stage of smelting, with additional limestone and alumina. (This slag would normally be a waste material). The cement clinker produced had the composition of commercial Portland cement, and met the physical test requirements of the Canadian Standards Association Specification A5-1951 for normal Portland cement as well as could be expected for a material produced on .such a small scale.

Jan 1, 1958

By G. E. Veins

A three-phase, continuously-operated, 250 kv.a. electric smelting furnace has been installed at the Mines Branch, Department of Mines and Technical Surveys, Ottawa, for the experimental treatment of ores and by-products of interest to the Canadian mining, metallurgical, and chemical industries. In the operation of this furnace particular emphasis is placed on the accumulation of quantitative data which will be useful in determining the most suitable smelting technique and the nature of the products, and in arriving at preliminary conclusions regarding the cast of power and electrodes. The results obtained in the experimental smelting of iron, manganese-iron, titanium- iron, nickel, and chromiumiron ores, and of a number of industrial by-products, clearly show the value of such treatment for materials of this type.

Jan 1, 1957

By G. E. Veins

This paper summarizes an investigation in which beneficiated ilmenite ore was smelted in a continuous, three-phase, 250 kv.a., open-top electric furnace. Minus %. inch ore was smelted, using the standard method. Fine ore, in the order of minus 14 mesh, was smelted in the briquetted form by the open bath method, and in the unagglomerated form by the cold dry-top method. The latter was shown to be superior. The data obtained .are discussed at some length. During the investigation, slag aver-aging 82.5 per cent Ti02 was produced over a period of 87 hours, the maximum being 85 per cent. Such slag should .be particularly attractive for the production of titanium tetrachloride, from which titaniurn metal is produced. The advantages of using paper-mill bark for producing a furnace charge of low bulk density, as required in cold dry-top smelting, were emphasized.

Jan 1, 1957