Search Documents

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By Guozhu Ye, Mikael Lindvall

"Swedish iron ore contains about 0.1 %V. The vanadium is reduced to the hot metal in a blast furnace and oxidised to the slag in a converter. The high V-content, up to 5 % V, leads to a very limited external application of the steel slag in Sweden. Since 2004, MISTRA - the Swedish Foundation for Strategic Environmental Research has together with the steel and mining industry in Sweden and Finland initiated and supported a long term project aiming at efficient recovery of vanadium in the slag, and at the same time a useful slag product with low V-content. The proposed concept consists of a reduction step and a phosphorus removal step. This paper will highlight some of the results with focus on the various metallurgical reactors used for slag reduction, including results from recently performed pilot trials using a DC furnace for cotreatment of metallurgical slags and other wastes.IntroductionToday, less than half of the produced LD-slag in Sweden is recycled to the blast furnace as a lime source and the rest is temporarily stored inside the steel plant. The steel slags cannot be used externally due to its content of vanadium and free lime. As the slag storage area is limited, this has become a problem for Swedish steel producers. The disposition of the slag is also a great waste of a valuable vanadium resource. The current potential value of vanadium in the discharged steel slag annually amounts to roughly US$ 100 million. Currently, Swerea MEFOS is conducting an 8-year vanadium recovery project called VILD (Vanadium in LD-slag) aiming at efficient recovery of vanadium and at the same time producing a useful slag product with low V-content. The project is financed by MISTRA - the Swedish Foundation for Strategic Environmental Research and the steel and mining industry in Sweden and Finland. Various reactors and process options have been tested in the past 7 years, from 3 kg laboratory scale, 150 kg induction furnace, 3 MVA pilot DC furnace, 5 MVA pilot AC furnace, 5 tons Kaldo furnace, to full scale direct hot slag reduction in the industrial site (12 tons of slag). This paper will introduce the VILD-concept and review the experiences gained from these trials. The advantages and disadvantages of the different options will be discussed and concluded."

Jan 1, 2012

By Tomlinson E, Lama RD

Drainage of gas has been practiced overseas for almost half a century. Peal advances in drainage of gas to combat high emissions became practicable in the late fifties and early sixties when the technology was standardised to use it under a variety of mining and geological conditions. Today methane drainage is practiced in the United Kingdom, Germany, France, Belgium, Poland, Czechoslovakia, Hungary, Ibmania, U.S.S.R., China, Japan, Canada, U.S.A. and Mexico. Australia entered the list of countries using gas drainage on 3rd March, 1980 when the first full scale gas drainage system was set up and commissioned at West Cliff Colliery to drain gas from the Bulli Seam. Methods used in Europe are different from those used in North America, Japan and Australia mainly because of the different mining methods and also because of the limited number of seams under extraction, relatively new coal fields, and comparatively larger distance between the seams. In spite of the difference in the technique, the basic aim is the same and that is to improve ventilation and reduce ventilation costs, alleviate dangerous gas accummulation, overcome outburst hazards and ultimately make mining safer and more efficient. Over the last decade, there has

Jan 1, 1982

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973

By Damien Enright, Franz-Werner Gerressen

CFA/ACIP pile is the most used single pass drilling method for deep foundation installations. It is constructed by rotating and driving a Continuous Flight Auger (CFA) into the ground at a controlled speed to the specified pile depth. Concrete is then pumped under continuous positive pressure through the hollow stem of the auger to fill the borehole as the auger is withdrawn. CFA/ACIP piles are preferred due to their high daily production capacity when used in suitable soil conditions. CFA/ACIP piles have been installed in the United States for decades and the industry has seen a huge development in equipment, installation process, monitoring and more. Nowadays, CFA/ACIP piles are installed using fully computer monitored drill rigs rather than a bulky crane and lead setup. Because of the torque and crowd offered by these rigs, piles can be installed to depths of more than 100 feet and diameters up to 48 inches. New age crane-based equipment with leader systems are than welcome to substitute old fashioned bulky cranes These new age crane-based systems combine the benefits of sufficient hydraulic power, fully equipped software, etc. with the additional benefits that they can do single pass drilling without extension systems, even when drill depths of more than 100 feet are required. The paper will explain the construction process and will discuss some jobsite references and experiences made using the new age crane-based equipment.

Oct 1, 2022

By H. Wagner

During the last few years a large number of pillars in different mines were investigated. Pillar conditions were evaluated using subjective, empirical, geophysical and numerical methods. A critical comparison of the different methods showed some interesting coherence. This paper concentrates on experiences using the p-wave velocities as an indicator of pillar conditions. Während den letzten Jahren wurde eine große Anzahl von Bergfesten in verschiedenen Bergwerken auf ihren Zustand hin untersucht. Hierzu wurden subjektive, empirische, geophysikalische sowie numerische Methoden angewandt. Dieser Vortrag beschäftigt sich mit den Erfahrungen beim Einsatz der p-Wellengeschwindigkeit zur Beschreibung des Festenzustandes. Le condition géotechnique d’une grand nombre des piliers des mines souterraines différentes sont examinées ces dernières années. On a appliqué des méthodes subjectives, empiriques, géophysiques et numériques. Ce rapport occupe aux expériences avec l’application de la vélocité des ondes de compression pour tracer le condition des piliers.

Jan 1, 2003

By Patrik Ericsson

During the 90?s Atlas Copco and LKAB developed a pioneering fully automatic long hole production drilling system based on the Atlas Copco Simba W469 drill rigs. These drill rigs have since then drilled about 8.000.000 drill meters at the LKAB Kiruna and Malmberget mines. In 2005 LKAB ordered three new Atlas Copco Simba W6 C, to complement Simba W469s still in operation. These new Simbas are based on the latest generation computerized drilling technology have proven to meet the expectations of LKAB and now form a base for future automation in Kiruna and Malmberget mines. This paper will present experiences from the introduction of Simba W6 C in LKAB Kiruna and Malmberget mines. The paper will also elaborate on the latest developments in remote access and remote control technology making it a common automation option available for all computerized Atlas Copco drill rigs.

May 1, 2007

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By Claude Cunningham

Ths oonoept of precise. eooursts timing with Elsotronic Delay Detonators (EDD’s) was first ssriously sddresssd in ths mid 80’s end much wss made of the cheapness end profusion of digital wstohes in terms of the likelihood of EDD’s also being cheap and essyto produce. Ten years Iater. with every major explosives group end many elsotronios groups having instituted projects to capitalize on the promise of these devices, production devices are still to come into asneral use.

Jan 1, 1994

By Harold Vance

EMPLOYERS of engineers have not always been satisfied with the training that young graduates have received in the conventional four-year course. Specifically, employers of petroleum engineers for a number of years have believed that a four-year course does not allow sufficient time for the student to secure a fundamental engineering background plus the fundamentals of petroleum engineering. A group of California employers went so far as to set up a type of curriculum for a petroleum-engineering course, which was based on four years of undergraduate work and one year of graduate work, with most of the petroleum-engineering courses included in the graduate year.

Jan 1, 1944

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By M. Cousineau, S. Gariepy

"Current business and corporate environments push for improving metal accounting practices in smelters. The ensuing projects commonly proceed along a bottom-up approach. As such, efforts are first put on reviewing the measurement system and then on remedying the identified weaknesses. The focus is thus moved to mass/metal balance only after the measurements upgrade process has been completed. However, practice has shown that assessing the high variances related to suboptimal measurement processes is complicated without the help of statistical data reconciliation. This bottom-up approach leads to a to-do list that can not only exceed available resources but also lack prioritization in view of achieving the targeted end use. This paper describes an upgrade project done differently where all the three dimensions of the metal accounting system: hardware, software, and people were instead involved at the onset. Personnel was thus trained on data reconciliation software at the beginning of the project to make the reconciled mass balance benefits available earlier in the upgrading project. This has pinpointed the most critical measurements where accuracy and reproducibility should be improved. Overall, not only the instrumentation retrofitting process has been streamlined, but the global risk for the whole upgrading project has been significantly lowered.INTRODUCTION Mining companies are pressured to improve their production accounting practices in response to the strengthening of corporate requirements for timely and accurate production reporting (Gaylard, Randolph, & Wortley, 2014). Smelters are not spared from these changes. However, their unique situation in the mining value chain set them as strategic targets for upgrading projects. They usually have a longer lifespan than concentrators thereby offering an extended lifecycle to justify investments. Furthermore, numerous smelters have toll agreements with third parties. Accurate cost and production accounting is, therefore, a vital piece of information to fix acceptable contract conditions. Mining companies are ultimately aiming at a clearer view of the operating performance of each business unit to improve their business decisions in a competitive environment. This sought for increase in visibility through plant performance can only be achieved through an upgrade of the metal accounting system. Figure 1 shows the different components of a state of the art system (Gaylard, Morrison, Randolph, Wortley, & Beck, 2009)."

Jan 1, 2017

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By J. N. Van der Merwe

The paper provides an overview of subsidence research which was done by the Sasol Company in South Africa over a period of more than six years. The magnitudes of subsidence elements in South Africa are largely similar to those in the U.S.A. and Australia, as opposed to Europe. The research resulted in a subsidence prediction method with a new approach to the prediction of ground strain. The paper also describes the effects of subsidence on various commonly occurring surface structures such as roads, overland conveyor belts, pipe lines and power pylons. It is concluded that while most structures are not specifically designed to accommodate mining induced displacements, they can nontheless be undermined safely and economically with only minor precautions.

Jan 1, 1986