Search Documents

By P. Saha, D. M. Chakrabarti, J. P. Srivastavam, P. Bhattacharyya, B. R. Sarkhel, Banerjeem B.

The phosphatic soil deposit at the Sukulu hills region of Uganda contains 10-12% P2O5. The ore occurs as a naturally degraded soil deposit containing a very sticky slime composed of earthy lateritic minerals. Desliming of the ore, which is imperative for its further beneficiation, is an extremely difficult hurdle to overcome for its commercial utilisation. Earlier studies on samples of the same ore at the National Metallurgical Laboratory (NML) and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of vigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slime. In the present paper an innovative use of the very strong shear-fields created inside a hydrocyclone has been discussed, that could effectively eliminate the stubborn slime from the ore. The standard design of the hydrocyclone was suitably modified to increase the shearing effect on the slurry. It was possible, through the application of this modified hydrocyclone, to not only totally eliminate all the stages of attrition scrubbing, but also to reduce the subsequent stages of hydrocycloning. The modified technique yielded a concentrate of grade comparable to that obtained by employing the earlier more complex flow sheet, with about 25% higher P2O5 recovery.

Jan 1, 2003

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By Pierre Longtin

"Replacing the aging roadway access to the iconic Golden Gate Bridge, thereby ensuring traffic safety and robustness in case of seismic occurrences, provided an opportunity for major design improvements as well as the development of a parkway that would include the construction of four new tunnels. With an eye to the future, the Doyle Drive replacement project aimed to meet the highest standards for environmental stewardship beyond regulatory requirements. Understanding that lighting equipment is the tunnel‘s subsystem that uses the most energy, the operator was looking for a sustainable solution to light the tunnels. An Intelligent Lighting Control System (ILCS), designed specifically for road tunnels, was acquired to individually control the almost 2000 luminaires lighting the four tunnels. This paper will show the results in terms of energy and operational savings generated over the nine months of operation between the commissioning and the conference in April 2016. INTRODUCTION Electrical & mechanical (E&M) equipment represents an average of 10 % of a tunnel total construction cost. Once the civil infrastructure completed, E&M equipment drives the main part of the expense during a tunnel useful life. Table 1 below describes the impact of various types of energy consumption and their cost impact in tunnels of less than 500 m. It is clear that lighting is the sub-system that requires the most energy. A good lighting strategy is the key to reducing energy consumption due to lighting and a viable solution that will bring important savings in tunnel operations.With a price of $0.14/kWh in California and a planned increase between 3% and 6% per year during the period 2013-2040, the tunnel operators could not afford to overlit the tunnels—particularly when they have to operate it for the next 30 years. However, they also need to maintain the right lighting level to ensure driver safety all the time. The Presidio Parkway project includes the Battery tunnels, which are 240 m (790 feet) and 230 m (750 feet) in length, and the Main Post tunnels, which are 280 m (920 feet) and 315 m (1030 feet) in length."

Jan 1, 2016

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By J H. Zietsman

The transition to more sustainable metal production is receiving much attention at present, and the iron and steel industry is at the centre of the conversation. New, more environmentally friendly production technologies, such as direct reduced iron (DRI) smelting furnaces, need to be developed in a short period of time. This necessitates increased use of computational modelling that incorporates more accurate material descriptions. The combination of large-scale multiphysics models of high-temperature processes with CALPHAD material descriptions leads to infeasible computation times. This can be resolved with the previously reported RapidThermo framework, which has been demonstrated to make equilibrium calculations orders of magnitude faster, within controllable limits of accuracy. In this paper, we explain how further material properties, which are important to modelling hightemperature reactors, can be added to the RapidThermo framework. This can improve the accuracy and usefulness of process and multiphysics models in the development of new technologies, which can significantly accelerate development cycles.

Aug 21, 2024

By Elhachmi Es-Sadiqi

"For over 40 years, CANMET has focused its research on value-added products and energy efficiency in the metals industry. The Efficient Metal Production Program is currently managed by Dr. Elhachmi Es-Sadiqi, and the Canadian steel industry is its main client — both directly and through international organizations such as the American Iron and Steel Institute (AISI) and the International Lead and Zinc Research Organization. AISI membership includes Canadian steel companies IPSCO, Dofasco, Stelco, Algoma Steel and Sidbec Dosco.Canada’s steel industry makes important contributions to the economy. The industry comprises 14 companies and employs 33 600 people in locations such as Sydney, Nova Scotia; Tracy, Quebec; Selkirk, Manitoba; Saskatoon, Saskatchewan; and Sault Ste. Marie, Ontario. With annual production at about 16 million tonnes, sales in 1995 totalled $11 billion, $3.8 billion of which was exported.Canada’s steel industry supplies the transportation, oil and gas, appliance, packaging and construction industries. It is at the forefront of new technology use and has a substantial support network to provide raw materials, equipment and service. Three main segments of the industry include flat-rolled products (e.g., plate and sheet steels), long products (e.g., concrete reinforcing bar and structural steel), and specialty and alloy steels (e.g., stainless steel and tool steels, in both long and flat products)."

Jan 1, 1998

By L. Van Wyk, J. Fernandez, J. Suarez, L. J. Diaz, A. Uria, D. Breeuwer

"Ventilation is an essential component of any underground mine, playing a vital role in ensuring the health and safety of workers, and a mine’s continuous operation. At a time when mining companies are increasingly having to move to deeper underground operations in pursuit of high-grade ore-bodies, the search is on for more efficient ventilation systems that will allow mining to be carried out at even deeper levels whilst ensuring the protection of workers and the maximisation of productivity through temperature management and the lowering of energy costs. Mining companies today are looking for innovative ways to deliver new technologies and procedures to enhance their mine’s profitability. Energy consumption by mine ventilation systems is higher than ever due to stringent specifications of underground equipment (primarily combustion engine emissions), air quality standards and mining at deeper levels which all require more powerful ventilation systems. With energy costs associated with operating ventilation systems being a mine’s second-highest cost of production after labour, finding the optimal ventilation solution is critical to a mine’s performance. Proper fan design remains a major factor in reducing capital expenditures (CAPEX) and operational expenditures (OPEX), which means that there are compelling reasons for making use of comprehensive factory testing at full power before fans are dispatched to site to simulate the mine’s current and future design requirements, and thus verify the fan’s effectiveness in ‘real’ conditions.INTRODUCTION A primary mine fan is considered the heartbeat of the entire mine ventilation system, drawing fresh air from the surface and providing a safe environment for miners. A ventilation system’s lack of performance often leads to a reduction in acceptable air quality levels for underground working operations and can potentially have an adverse impact on production rates."

Jan 1, 2019

By D. Baker

Alternative material handling methods are allowing material handling operations to be performed with increased cost savings. This allows for higher production levels with better returns. RAHCO International Inc.'s Continuous Mining Excavator (CME) has recently received a lot of attention due in part to its operating efficiency, flexibility, and associated low operating costs. The CME is designed to perform three primary functions. These include material excavation, sizing and loading operations. In many applications, a drilling and blasting process can be eliminated. The CME was developed originally in 1985 for open pit coal mining. See figure I. Since this time, it has been proven an effective system for excavating many other types of materials including friable and sticky materials. It has also been shown to suitably handle hard rock in certain site conditions.

Jan 1, 1998

By M. Saghaeian, R. Hejazi, M. Mohammadinejad, M. Zare

"Water quality and quantity at the Tailing Thickening Section of processing plants is considered to be a crucial factor and impacts the performance of several sections. Therefore, gaining stable and effective performance at the Tailing Thickener Section is one of the principal goals of minerals processing plants. Different factors such as: qualitative and quantitative sustainability of plant feed, the balance between the mass of input and output water flow, the dissolving method and distribution of flocculant and the amount of dirt, solid percent of thickener inlet pulp, affect the performance of Tailing Thickener. The present study investigates the successful improvement of Tailing Thickener performance at Jalal Abad Hematite Iron Ore Concentrate plant through optimizing the above operational parameters. For this purpose, the following optimizations have been done: homogeneity and sustainability of plant input feed rates, fine pulp removal collected by the bag filters at the input of the thickener, adding an quietness box before moving the tail pulp into the thickener to reduce the pulp turbulence, replacing flocculant pump and injection pipes, improving water mass balance which leads to optimizing and stabilizing the concentration of input tail pulp into the thickener, adding a mixer to increase the flocculant preparation time, increasing the locations for adding flocculant to thickener from 1 point to 6 points. Applying the above modifications and monitoring the Tailing Thickener performance over the course of months, has led to the improvement of recovered water quality from 500 ppm to 200 ppm, increasing the solid underflow of the thickener from 40% to 48.5%, and similarly, reducing water loss by 60%. Of other important effects, due to improvement of water quality, grade of final concentrate 0.5% increased and because of 73% increase in monthly working hour, concentrate tonnage 55% increased. Finally, sludge thickener optimization has had a significant effect in selecting and designing the dewatering system from the underflow of the sludge thickener."

Jan 1, 2018

By L. D. Ellison

The ventilation of a bituminous coal mine by means t of a Forced and, or, Exhaust system of ventilation is certainly not new to the mining industry, however, we know from experience that the ventilation of every coal mine presents a variety of problems which are in some instances approached by different methods or means, As in every such problem, there is some difference of opinion as to the advantages and disadvantages of s Exhaust versus Forced ventilation, particularly with regard to safe and effective ventilation of an active pillar area in a gaseous coal mine. We at Island Creek, certainly concede that it is possible to safely ventilate a coal mine by means of Forced ventilation, However, following many years experience in operating a coal mine in an extremely gaseous coal seam, we prefer using an Exhaust system, that is, to reduce the inside mine pressure to a minus atmospheric pressure by means of a mechanically operated fan. This method assures that the return air moving through established airways toward the fan will continue to move in that same direction for a limited time should the fan stop for any reason, also assuring that in the event of a large area fall, the air from the abandoned workings will move directly to the suction side or to the return airways.

Jan 1, 1960

By S. A. Richards

Business planning in the coal' industry revolves around the production and quality forecast. It is difficult to accurately estimate costs and revenues until the production forecast is made. At mines where production comes from multiple sections, quality is tied to each section's production. Blending becomes a part of the planning process. In order to respond to rapidly changing business climate, a reliable program is needed to accurately forecast the effects of changes in key parameters affecting the production. This paper discusses an efficient, intuitive, and economical approach to underground coal mine planning program which uses a PC-based relational database as the programming platform to forecast production and quality. The program was developed at a major coal company. The relational nature of the production planning data, the programming algorithm, and the underlying principles are discussed in this paper.

Jan 1, 1994

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By Zhiyuan Ma, Yong Liu, Xianjin Lyu, Jianfang Lyu, Jikui Zhou

A stable and continuous leaching process for niobium and tantalum extraction from ferrocolumbium tantalum (FT) was developed. The effects of initial concentration of HF and H2SO4, grinding fineness, leaching time, and temperature on the leaching rate of Ta, Nb, Fe, and Si were studied. Experimental results show that the leaching rates of Ta, Nb, Fe, and Si were enhanced by the increase of acid concentrate, fineness, leaching time, and leaching temperature. The optimum process conditions are HF initial concentration of 5 mol/L, H2SO4 initial concentration of 2.5 mol/L, − 74 μm percentage of 65%, leaching time of 20 min, and leaching temperature of 25 °C. Continuous leaching of FT was carried out by feeding ore and acid every 20 min. By leaching with HF − H2SO4 for 4 h, then adding appropriate amount of HNO3 into the solution and keeping for another 1 h, a high Nb extraction rate of 99.8% was achieved. The established method provides a promising technique for the high-efficiency separation of niobium and tantalum from FT.

Jun 5, 2022

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

Steel slag is an industrial byproduct of steelmaking that is mainly composed of calcium, iron, silicon and magnesium. In addition, depending on the different raw materials entering the furnace, steel slag contains a certain amount of vanadium that is the main source of vanadium production, accounting for 69 percent of the species of the total vanadium raw material [1]. From experience, the production of one ton of steel will generate 1.0 to 1.5 tons of steel slag [2]. However, the utilization efficiency of steel slag is less than 30 percent, and a large amount of steel slag is identified as waste and stacked in tailings. The random stacking of steel slag not only wastes large amounts of limited steel and land resources but also exerts pressure on the environment [3], making it imperative to research the effective utilization of steel slag and recycling of metal resources.

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003