Search Documents

By J. P. Vandenhoeck

Sizing devices used commercially are unfortunately not 100% efficient, the splits that can be obtained are usually inferior to the results obtained in the laboratory. Often the capital and operating costs of equipment capable of high sizing efficiency cannot be justified by the economics or requirements of the process. To reconcile the desired sizing efficiency needed to obtain optimum process requirements with the sizing efficiency of equipment economically practical, it is often necessary or desirable to predict the gradation and weight splits of the products obtained based on the expectant efficiency of the contemplated sizing device or method. The less efficient the sizing device one must employ, the more important it is to know the results that may be expected for the establishment of the optimum flow sheet and the more difficult it becomes to estimate the results accurately. Air classification equipment which sizes materials by opposing the drag force created by an air stream acting on a particle with a combination of gravitational, inertial or centrifugal forces are substantially less efficient than, for example, a laboratory sieve analysis. Air classifiers allow oversize material to contaminate the fine fraction and leave undersize material in the coarse fraction. The techniques employed to predict the gradation and weight splits obtained from air classification outlined below are adaptable to other sizing devices less than 100% efficient such as screens, sifters and wet classifiers.

Jan 1, 1965

By D. Xie

An in situ gravimetric technique based on wetting and capillary action principles has been used to investigate the wetting and penetration of synthesized alumina samples and commercial magnesia spinel refractories by CaO-SiO2-Al2O3-Fe2O3slags. Synthetic slags of 40CaO-40SiO2-20Al2O3 (in weight per cent) with 0 to 9 weight per cent Fe2O3were used and the experiments were conducted at temperatures 1370 to 1470ºC under argon. The contact time between the sample and the slag was 30 minutes. The results show that the wetting and penetration are enhanced by the iron oxide addition in the slags. Addition of Fe2O3from 0 to 9 weight per cent resulted in a significant increase in the slag penetration into the magnesia spinel refractory by a factor of about 7 and a moderate increase in the synthesized alumina by about 60 per cent. The addition of Fe2O3enhanced the wetting (??cos?, where ? is the surface tension of the slag and the contact angle between the slag and the refractory) by 5 to 18 per cent. An increase in temperature from 1370ºC to 1470ºC resulted in a significant increase in the penetration of a 6 weight per cent Fe2O3slag in the alumina and magnesia samples by a factor of4 to 5 and a decrease in wetting by approximately 30 per cent. Keywords: refractories, slag penetration, wetting.

Jan 1, 2004

By Li Qihou

Mono-disperse ZnS and CdS nano-particles were prepared by the homogenous precipitation method and the effects of SO42-,NO3- and Cl-ions on crystalline of particles were investigated experimentally. The results showed that these anions had no influence on the crystalline of ZnS, but different crystalline CdS ultrafine particles were produced in different anion systems, where the blend-type CdS was obtained from natrate or sulphate solution, and wurtzite-type CdS from chloride solution. It was ascribed to the coordination of Cl- and Cd2+ that altered the supersaturation of precipitate ions in the solution, the existing growth units and their connecting patterns, thereby producing wurtzite-type CdS with a more stable structure.

Jan 1, 2006

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By Honggang Zhong, Wei Du, Qijie Zhai, Junjie Sun, Jingzheng Ye

"Effects of pouring temperature and cooling water flux on solidification structure of ferritic stainless steel are investigated with a thermal simulation setup. The results show that with pouring temperatures 1518° C, 1528° C, 1538° C and 1548° C, both Lmean (the mean length between columnar to equiaxed transition(CET) position and chill surface of the samples) and the mean dimension of equiaxed grains increase. On the other hand, with cooling water flux 400, 800, 1200 and 1600mL/min, Lmean gradually increases, and the mean dimension of equiaxed grains decreases. In addition, low pouring temperature and cooling water flux enlarge the ratio of fine equiaxed grains.IntroductionFerritic stainless steel plays an important role in industry products nowadays. Compared with austenitic stainless steel which contains both chromium and nickel, ferritic stainless steel can obtain good corrosion resistance despite the absence of nickel [ 1]. F erritic stainless steel has been widely applied in automotive exhaust systems [2], electrical equipment, construction and chemical industries and also has broad development prospects. At present, continuous casting technique has developed into an important technology applied in iron and steel making. The solidification structure of continuous casting slab has significant influence on the final properties of stainless steel. The developed columnar grains of ferritic stainless steel would result in negative effects on mechanical property [3]. However, fine and homogeneou& equiaxed grains can improve the comprehensive properties of ferritic stainless steel [4] Therefore, it makes great sense to promote the columnar to equiaxed grain transition (CET). Recently Baosteel has developed a new type of Cr-saved ferritic stainless steel, but the effect of continuous casting conditions on its solidification structure is unknown. It is important to investigate the effects of solidification conditions on solidification structure of this new ferritic stainless steel, which can give guidance for optimizing the production process."

Jan 1, 2014

By P. N. Anyalebechi

The effects of solidification rate (0.4-26.1 K/s) and alloying elements on the cast microstructures of aluminum alloy 5182 have been investigated with directionally cooled laboratory-size ingots. The alloying elements examined included Mg (3.6-4.7 wt.%), Mn (0.35-0.75 wt.%), Fe (0.11- 0.42 wt.%), Cu (0.03-0.25 wt.%), and Si (0.11-0.28 wt.%). These reflect the chemical compositions of AA 5182 end stocks with high recycled used beverage container (UBC) content. For a given chemical composition, the average dendrite cell and constituent phase particle size decreased with increase in average solidification rate. In general, within the level investigated, Mg did not have a significant effect on the types, volume fractions, and average sizes of the constituent phase particles. However, increase in Mn, Si, Fe, and Cu increased average sizes and volume fractions of the constituent phase particles.

Jan 1, 2010

By Dávila-Pulido. G., L. Magallanes-Hernández, F. López-Saucedo, J. Batista Rodríguez, A. Uribe-Salas

"This paper presents the results of tests performed to study the effect of slurry solids concentration on the behavior of gas dispersion in industrial-scale mechanical flotation cells. The experiments were conducted at five concentrator facilities run by a Mexican mining company, specifically in the rougher bank of the lead/zinc flotation circuits. Those mechanical cells having significant contribution to the performance of the circuit, that is, the cells that enable high recovery, were characterized. The measurement protocol enables measurement of the superficial gas velocity, gas holdup and bubble size, and sampling of the mineral slurry. The measured data indicate that bubble size and gas holdup decreases as the concentration of solids increases. IntroductionThe process of mineral concentration by flotation is based on contact between particles and air bubbles, the selective adhesion of hydrophobic particles onto the bubbles, and the rising of the bubble-particle aggregates to the surface of the flotation cell to overflow over the lip to form the concentrate. It is now accepted that the physical and chemical process variables that control the flotation of hydrophobic particles are closely related to gas dispersion (Schwarz and Alexander, 2005). Gas dispersion is defined by the superficial gas velocity, Jg (Torrealba-Vargas, Gomez and Finch, 2006), the gas holdup, eg (Tavera, Gomez and Finch, 1997), the bubble size, d32 (Dobby and Finch, 1986; Gorain et al., 1995; Hernandez-Aguilar et al., 2004) , and the bubble surface area flux, Sb (Manqiu and Finch, 1989; Manqiu, Finch and Uribe-Salas, 1991). In recent years, the advances that have been made in sensor technology have enabled the characterization of gas dispersion in industrial flotation cells with excellent results (Gomez and Finch, 2007). This technology advancement has allowed the gaining of a deeper understanding of such complex mechanisms as carrying capacity (Yianatos and Contreras, 2010), collection efficiency (Gorain, Franzidis and Manlapig, 1997; Massinaei et al., 2009) and bubble coalescence (Finch, Nesset and Acuña, 2008; Zangooi, Gomez and Finch, 2010)."

Jan 1, 2017

By Ralph Harris, Qi Xia

"Gold cyanidation rates are known to be limited by the rate of oxygen dissolution in the cyanidation tanks. The effect of solids loading on the oxygen dissolution rates is not obvious and the results of previous studies are ambiguous. The present paper presents an analysis of oxygen dissolution rates using a ""spent"" commercial gold slurry diluted to various levels of solids loading. It was found, in an 170 litre stirred tank reactor using an inverted cone sparger, that under certain high loading conditions, there was a decrease of as much as 50 %, i.e., there was a halving of the rate of oxygen dissolution as compared to that in clean water. In particular, it was observed that, due to gas flooding of the impeller, there was a drop in kLa even with an increase of gas velocity. Gas holdup reached a maximum value of only 1.7 %. The total power consumption was between 0.06- 0 .10 kw/m3 within the range of gas velocity before flooding occurred. The decrease in oxygen dissolution rate with increased solids loadings is believed to be mainly due to the increase in the apparent viscosity which reduced the turbulence and shearing effect and resulted in larger bubbles and hence reduced the reaction area a. The interrelations between solids loading, gas holdup, flow pattern, power consumption, and liquid mass transfer coefficient are discussed.IntroductionThe reactors generally used in gold cyanidation are Stirred Tank Reactors (STR). Compared with other types of reactors like fluidized bed reactor and column reactor, STR is of particular importance due to its wide application in industry. It is reported that the stirred tank reactor is used for more than 50 % of the world's chemical production (Xu and McGrath, 1996)."

Jan 1, 1997

By Yuki Koshino, Kenji Kaneko, Yasuhiro Aruga, Takuya Maeda

"In general, there is a strong correlation between dislocation characteristics and mechanical properties of aluminum alloys. In this study, dislocation characteristics of tensile deformed Al-Mg alloys were examined by transmission electron microscopy. An Increase in the solute concentration, ranging between 0.3 and 1.1%, Mg leads to increase in strength and decrease in uniform elongation. The accumulation of dislocations during the tensile deformation is observed in lower strain as the concentration of solute Mg in the alloy is higher. It is believed that the solute Mg in Al-Mg alloy promotes the accumulation of dislocation during the tensile deformation resulting in the decrease in elongation.INTRODUCTION The influences of the amount of Mg concentration on the tensile properties of Al-Mg alloys has been investigated by many researchers. It has been understood that the tensile ductility of Al-Mg alloy is higher for the Al-Mg alloys with higher Mg concentration beyond 2 mass% (Mukai, Higashi, Hirano & Tanimura, 1993). Uchida and Yoshida (1995) reported the formation of microbands during the tensile deformation due to the localization of dislocations, and the amount of microbands were reduced when the Mg concentration of the Al-Mg alloy was increased from 3 to 9 mass%. Their study suggested that the dynamic recovery of dislocation was retarded due to the increase of the Mg concentration during the tensile deformation, which resulted the increase in ductility. On the other hand, in the case of Al-Mg alloys with the Mg concentration less than 3 mass%, the reason why the ductility of Al-Mg alloys decreases with increasing Mg concentration has not been sufficiently investigated. In general, the Mg concentration used for automotive usage is less than 1 mass%, in the case of Al-Mg-Si alloys (Aoki, 2013). Therefore, to clarify the roles of Mg in the low concentration range on ductility of aluminum alloys and to elucidate its mechanism contribute to alloy design of Al-Mg-Si alloys having good formability."

Jan 1, 2018

By M. A. Wei

Effects due to some metal cations, such as Ca2+, Mg2+,Fe2+, Fe3+, Cu+, Cu2+, Zn2+ and Al3+ etc., which are produced in the pulp when the complicated ore is dipped in the deioned water, on the flotation of chalcopyrite and galena with the isopropyl thionocarbamate as collector have been studied. It is found that chalcopyrite floatability is not influenced by these cations, and the cations can be di-vided into three types according to their effects on the purified galena?s floatability with the same conditions, as activator such as Cu+; as depressant such as Al3+, Fe3+, Fe2+, Zn2+ and Cu2+ , unaffective such as Mg2+ and Ca2+.

Jan 1, 2014

By M Olsson, U Nyberg, K Widenberg, P Svedensten, F Ouchterlony

During 2007 and 2008, the project Optimal Fragmentation in Blasting II was conducted at the Långåsen quarry of NCC Roads AB near Arlanda. The main goals were:an evaluation of the effect of using electronic delay detonators (EDDs) in quarry blastinga validation of the design curve concept introduced at the Vändle quarry.Five production blasts were monitored. After a first trial round, the remaining four rounds each had about 100 Ø89 mm holes in a 14–19 m high bench charged with site mixed emulsions. In rounds 1 and 2, a tighter pattern than normal was used in one half of the rounds, raising the specific charge there from 0.7 to 1.0 kg/m3. Non-electric initiation was used with two holes per 25 ms delay in-row and 67 ms between rows. In rounds 3 and 4, electronic delay detonators were used instead, with 10 and 5 ms in-row delays respectively.The monitoring encompassed drill hole collaring and alignment, in-hole deviations, the rock structure in the bench faces from 3D imaging, first row burdens, etc. Eleven 400 t samples were taken from the muck piles and sorted in the quarry and sieved in the laboratory (lab). The lab data made up a fines tail that was grafted onto the in-pit sorting data to form sieving curves for the test piles. These curves were then compensated for the absence of boulders to construct the sieving curves for the blasted muck pile.These have been used to derive fragmentation model formulas for the non-electric rounds, also called design formulas. They are based on blast geometry, charging data and the properties of the rock mass. The formulas may be used to estimate the effect of changing blasthole pattern, borehole diameter and stemming length for example.The use of EDDs gave several unexpected results. In comparison with non-electric initiated rounds with a somewhat lower specific charge the fragmentation was much coarser; x50 increased from 160 to 200 mm. The effect of raising the specific charge in the non-electric initiated rounds from 0.72 to 0.99 kg/m3 was a much finer fragmentation; x50 decreased from 160 to 120 mm.CITATION:Ouchterlony, F, Nyberg, U, Olsson, M, Widenberg, K and Svedensten, P, 2015. Effects of specific charge and electronic delay detonators on fragmentation in an aggregate quarry – building fragmentation model design curves, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 727–740 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Timothy Barton

The uniaxial compressive strength (UCS) is the most fundamental measurement used in geotechnical rock characterization for mine design. While there are standardized procedures for how to conduct UCS tests, there are no firm guidelines as to when to conduct them. However, it is well known that the strengths of at least some rocks can change during the time between when the core first comes up out of the hole and when it is prepared and tested in the lab. The goal of this NIOSH (National Institute for Occupational Safety and Health) study was to evaluate UCS changes occurring in a broad range of weak coal measure rocks over a one-year time span. The study found the highest moisture contents were measured when the core was fresh, immediately after it was taken from the hole. The specimens then dried rapidly over the next few weeks. Subsequently, sample moisture contents decreased slightly in the winter and increased in the summer in response to the ambient changes in humidity. The measured UCS of the core also changed during the year, apparently in response to changes in the moisture content. The UCS values from the dry, winter months were, on average, 60% higher than the values obtained when the core was fresh, and the summer UCS was approximately 11% lower than the winter UCS. These findings have implications for the use of UCS as an input parameter for both empirical and numerical mine design methods. UCS values of unprotected core tested weeks to months after drilling can be significantly stronger and indicate stronger roof sequences than warranted. In order to obtain the most representative and reliable UCS value, it is necessary to test the core, or wrap and seal it, at the drill site shortly after recovery.

Jan 1, 2008

By Murat Alkan

In this study, a self-propagating high-temperature synthesis (SHS) and following acid leaching techniques were carried out to produce boron carbide (B4C) powder. First, B2O3 was obtained through calcinations of H3BO3 at 1073 K for 2 hours. Then, the glassy B2O3 obtained was crushed and sieved. In the SHS experiments, different amounts of B2O3, Mg and C black were used. The SHS product was obtained in the form of black, spongy solid. In the leaching step, the SHS product was leached in a HCl solution to eliminate the MgO and Mg3B2O6. The effect of acid concentration on the selective leaching was studied at different concentration range, solid/liquid (S/L) ratio, and temperature. The products obtained were characterized by using X-ray diffraction, chemical analysis and SEM techniques.

Jan 1, 2009

By Jonq-Keh Lee

This paper deals with the effects of air leakage from intake to return airways through a series of stoppings on the analysis of coal mine ventilation. The mathematical model which assumes continuous leakage along adjoining intake and return airways is reviewed, and a new mathematical approach is presented based upon the concentrated leakage through individual stoppings. The procedure incorporating the new method in the analysis of coal mine ventilation networks is also discussed.

Jan 1, 1984

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021

By Diane F. Baker, Cathy Aimone-Martin

A series of small-scale explosive experiments were conducted in a perlite mine near Socorro, New Mexico. These experiments were a joint effort between Los Alamos National Laboratory, New Mexico Institute Of Mining and Technology, Southern Methodist University, and Defense Nuclear Agency. The purpose of these tests was to measure the changes in the shock wave and seismic coupling as a function of depth of burial and structural setting. The size of the explosive charges ranged from 1 to 68 kg. Over 1150 measurements of velocity and acceleration were made on thirteen experiments using three component sensors. The sensors were placed to maximize the azimuthal coverage as well as to provide data at a variety of ranges from ~1 to 130 m A few far field measurements were made at ranges of ~2Êkm. While the bulk of the measurements were made on the surface, high g accelerometers were placed in one instrumentation borehole to provide some free-field measurements. Preliminary results indicate that significant differences in the amplitudes of signals can occur when the location of the explosive charges are changed by only meters. Part of the observed difference is attributed to variations in the rock immediately adjacent to the charge affecting the shock coupling; and part to the effects of the site characteristics.

Jan 1, 1994

By Don Kay

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By Carter J. P

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By M. Sadegh Safarzadeh, Erich U. Petersen, Jan D. Miller

"An acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2•4H2O, PbSO4 and Cu0.47Fe0.53SO4•H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 hours with a sulfuric acid-toconcentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different concentrations. The purpose of this paper is to present our examination of the effects of sulfuric acid dosage on the extractions of Cu, Fe, and As from an enargite concentrate. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.IntroductionThe occurrence of enargite (Cu3AsS4) in copper ores and concentrates and the associated high arsenic values in such resources have resulted in a considerable decrease in the demand for such concentrates because they cannot be economically processed using conventional technologies such as smelting and atmospheric leaching (Mihajlovic et al., 2011). The exploitation of such problematic deposits through competitive treatment strategies will be required in the near future in order to satisfy increasing pressure from the copper market. It is expected that the average arsenic grade of copper concentrates will increase from 0.17% in 2008 to 0.22% by 2020 (Mayhew et al., 2011).The acid bake-leach process was identified and selected for further investigation at the University of Utah as a possible process alternative for the treatment of enargite concentrates. In this case, adequate amounts of concentrated sulfuric acid are mixed with the concentrate and heated to the temperature range 150-300°C. Subsequently, the baked material is leached with water/weak acid and the acid bake-leach process has some advantages over conventional sulfuric acid leaching (Prater et al., 1970). During water leaching, metal sulfates are released in solution, after which they can be extracted through well-known hydrometallurgical techniques. While the majority of the work has been done on oxide minerals, there is a limited record of sulfuric acid baking of sulfides."

Jan 1, 2015

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006