Search Documents

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

By C. P. Besse, N. F. LeBlanc

Described in this paper are oceanographic data which should be considered by an offshore design engineer and methods for developing a design wave height from the oceanographic data. The selection of a design wave is predicated on contemplated waves which might affect the site throughout the life of the structure. Selection of a design wave height may be based on (1) arbitrarily established recurrence Frequencies of hurricanes affecting the structure (predicted wave heights are associated with the expected variations of forces resulting from these waves) and (2) a risk-type evaluation wherein all possible storms affecting the area are considered (anticipated wave heights are associated with both investment plus risk costs and expected variations of forces). It is shown how the following oceanographic predictions are integrated into design considerations: (1) a classification of storm intensity which considers all recorded storms which affected the design area, (2) the recurrence interval of storms of a given- intensity (this interval is dependent on the extent of the geographical area considered in the design problem) and (3) a forecast of all wave heights which might affect the area (geometry of a structure often necessitates consideration of waves from a multiplicity of directions). The authors believe that the described techniques can result in selecting an adequate and reasonable design wave. INTRODUCTION Since the inception of offshore operations in the Gulf of Mexico, engineers engaged in designing suuctural facilities have been plagued with the problem of selecting an adequate and reasonable design wave. In the development of any offshore structure it is mandatory that the engineer evaluate the ability of the structure to withstand the ocean waves to which it will be subjected. Selecting such design waves quite naturally necessitates a coalition of the oceanographer and the design engineer. The oceanographer must provide a detailed knowledge of scientific principles which govern the behavior of waters in the Gulf of Mexico. He should also have an adequate knowledge of the manner in which design waves are utilized by the engineer. Although the design engineer's primary responsibility is applying the oceanographer's specialized knowledge in the creation of real structures, it is important that he possess some knowledge of related oceanographic principles to reasonably evaluate and apply the recommendations of the oceanographer. In the Gulf of Mexico it is the hurricane wind waves which generally govern the design of an offshore facility. The oceanographer must therefore develop techniques for predicting the heights, periods and frequency of all hurricane waves which might affect a particular structure. From this mass of oceanographic data, the design engineer must select the design waves which will apply to his particular design. PAST STUDIES ON FREQUENCY AND AMPLITUDE OF HURRICANE WIND WAVES Past oceanographic studies on the frequency of hurricane wave heights in the Gulf of Mexico have been devoted largely to predicting the recurrence interval of hurricanes which will generate maximum significant waves of given heights. The maximum significant wave height is the average height of the highest one third of the waves in that portion of the storm producing maximum wave heights. Since these waves occur over a relatively small portion of the storm (Fig. 1) and since the paths of hurricanes vary considerably (Fig. 2), the recurrence frequency of such heights is largely a function of the extent of the geographical area considered. In establishing the frequency of maximum significant waves for the entire American Gulf coast, the major fully developed hurricanes which affected the coastline from BrOwnsville, Tex., to Key West, Fla., were considered (Fig. 2). These Storms were selected and described by C. L-

By J. A. Musselman, P. F. Gnirk

A study was made of indexed penetrations by a single dull bit tooth under statically applied loads into rock subjected to confining pressures from atmospheric to 5,000 p.si and atmospheric pore pressure. Experimental results obtained with a 45" wedge tooth over the above range of pressures are presented for two limestones and a sandstone, a variely of indexing distances and two degrees of tooth dullness. The optimum distance between successive bit-tooth penetrations required for maximum rock damage and chip formation decreases substantially with increa.sing confining pressure above the brittle-to-ductile transition pressure of a particular rock. However, the distance remains approximately constant for a variation in confining pressure below the transition pressure. At a given confining pressure, the bit-tooth force required lor chip formation is constant for indexing distances greater than optimum, but generally decreases linearly with decreasing indexing distance for distances less than optimum. The chip-formation force data obtained at confining pressures for which the chip-generation mechanism is macroscopic-ally of a pseudoplastic nature compare favorably with previous theoretical results for indexed dull hit-tooth penetrntion into an idealized, rigid, perfectly plastic rock. INTRODUCTION To study the cutting action of a roller-cone bit, the interaction of a penetrating bit tooth with craters formed in a rock surfacc by the passage of previous bit teeth must be considered. Current knowledge of the basic mechanics of bit tooth-rock intcract:on under simulated borehole environmental conditions has been extensively reviewed.',' Particularly of current interest are the effects of bit-tooth shape, distance between successive penetrations and differential pressure at the rock surface on the extent of the interaction. Pertinent to this paper are results of an experimental investigationb f the interaction between successive penetrations by sharp, wedge-shaped bit teeth. It was demonstrated that both bit-tooth angle and differential pressure influence the extent of rock damage between successive bit-tooth penetrations. Specifically, the optimum or minimum distance between successive penetrations required for maximum interact'on or chip generation tends to decrease with decreasing bit-tooth angle and increasing differential pressure. In addition, at differential pressures on the order of 2,000 psi for four va- rieties of limestones and sandstones, the macroscopic mechanism of chip formation exhibits a transition from brittle to ductile. In this paper, experimental consideration is given to successive or indexed penetrat ons by wedge-shaped bit teeth. Since pore pressure in a rock sample is maintained at atmospheric pressure, the differential pressure at the fluid-rock interface is equal to the confining pressure. The degrees of bit-tooth dullness include teeth with flat and round apexes (Fig. 1). Of primary concern in this paper are the bit-tooth forces required for chip formation, the macroscopic mechanism of chip formation and the minimum distance between successive penetrations, i.e., optimum indexing distance required for maximum rock damage, as functions of differential pressure. Of further interest is a comparison of actual bit-tooth chip formation forces at elevated differential pressures with calculated forces from previous theoretical results4 for indexed dull bit tooth penetration into a rigid-plastic rock. EXPERIMENTAL APPARATUS AND PROCEDURE The experimental apparatus consists of a pressure vessel equipped with a piston through the side of the vessel (Fig. 2). A single bit tooth inserted in the lower end of the piston is forced at a desired rate into the rock when the ram pressure chamber is pressurized. Electrical instrumentation incorporated into the apparatus yields a graphical plot of force on the piston as a function of bit-tooth penetration or displacement into the rock. Since the piston and ram assembly are in force equilibrium for a constant confining pressure in the main vessel, the fluid volume in the vessel remains constant during bit-tooth penetration. Hence, the force resisting penetration of the tooth is independent of the force exerted on either end of the as-

By G. J. Wilson

Difficulties experienced in correlating vertical and lateral locations of subsurface features that are encountered in directional wells prompted critical review of the tangential method of computing directional surveys. Inherent discrepancies were indicated to cause small incremental but significantly large cumulative errors in computed vertical depth and horizontal departure. A radius of curvature method, developed for planning and analyzing directional wells, was studied as a means of more accurately calculating survey data. Errors incurred in the tangential method were not present in the radius of curvature method. Conflicting assumptions in calculating dog-leg severity by the tangential method were resolved by a new procedure that was derived from the radius of curvature method. Results of the investigation showed the radius of curvature method to be an improved method for computing directional surveys. Introduction Many improvements in directional drilling tools and techniques have been made in the past 10 years,' but the method of computing survey data has remained virtually unchanged. While use of computers greatly aids the process of calculation' and eliminates many human errors, manual and computer calculations are still made with the assumption that the wellbore consists of straight-line segments. This paper points out discrepancies in the method and presents an improved method in which the wellbore is assumed to be curved. Tangential Method The method presently used to calculate vertical depth, horizontal departure and direction coordinates with measured values of well depth, inclination angle and direction angle is termed the tangential method. This term stems from performing calculations with a series of straight-line segments, with each segment assumed to be tangent to the wellbore at a corresponding survey point. A segment is defined by inclination and direction angles measured at only the lower or deeper end. Consequently, a discrepancy or error is introduced for each segment. Errors are not of extreme magnitude, but cumulatively are significant due to the need to define as accurately as possible the vertical and lateral location of subsurface features such as pay tops, fluid contacts and fault cuts encountered in expensive directional well bores. In Fig. 1, the curved-line segment ab represents a portion of the actual borehole as viewed in the vertical plane. Points a and b are survey stations and +, is the inclination angle at point b. The curved-line segment ab is assumed to be the straight-line segment arb of a length equal to ab and tangent at point b to the curved-line segment. Lengths a'c' and c'b are equal to a'b cos +, and a'b sin +,, respectively. Point a already has been fixed by calcillations performed with survey data obtained at point a, and calculated lengths m'c' and c'b are projected as lengths from point a, rather than from point a'. Point b1 is thus fixed and assumed to represent the actual point b. Calculated length ac" is shorter than actual length ac, and calculated length c"bl is longer than actual length cb. Since b1 is the point from which the next deeper segment will be projected, errors are cumulative. Cumulative error continues to increase as long as the inclination angle continues to increase. When the inclination angle decreases (Fig. 2), calculated length ac" is longer than actual length ac, and calculated length c"bl is shorter than actual length cb. These errors also are cumulative, but differences between calculated and actual lengths are opposite in mathematical sign to differences demonstrated in

Jan 1, 1969

By D. S. Rowley, F. C. Appl

Assuming that rock behavior, during cutting with a single diamond, may be approximated by that of a rigid, Coulomb, plastic material, a theory of single diamond cutting action has been developed. Using this theory, the stresses on the diamond cutting surface and the components of the cutting force have been determined. Theoretical results agree reasonably well with available experimental data. The theory of cutting of single diamonds may be used as the basis for subsequent study of the perfonnance of surface set diamond drill bits and other surface set diamond cutting tools. INTRODUCTION For more than twenty years, surface set diamond bits have been used successfully in the mining and petroleum industries to drill and core rock formations that range from medium hard to the hardest known formations. Most extremely hard rock formations cannot be economically drilled or cored by any other means. In view of the growing use and importance of surface set diamond drill bits, it is reasonable to study the way in which these tools cut, and the factors that influence wear of the diamonds. Such knowledge will contribute to better bit design and will improve operating procedures. To analyze the cutting performance of these tools it is appropriate to consider the way in which an individual diamond cuts. Once this is established, the over-all performance of the bits can be determined by considering the total effect of the individual diamonds. In recent years there has been a growing interest in rock mechanics and there now exist several publications dealing with the deformation and failure of rocks. Notable experimental work has been reported by Bredthauer,1 Handin and Hager,2, 3 and Gnirk and Cheatham.4 An extensive collection of data pertaining to rock properties at low confining pressures has been given by Wuerker.5 Cheatham and Gnirk have recently presented an excellent review of the state of knowledge regarding analytical and experimental rock deformation and failure.6 Generally rocks are extremely weak in uniaxial tension, and weak or only moderately strong in uniaxial compression. Both tensile failure and compressive failure are generally brittle in nature. This means that there is little or no deformation or "flow" of the material before shear or tensile fracture occurs. Thus, until fracture occurs, rock behaves very nearly like an elastic material in uniaxial stress. Significant changes in behavior of rock occur under conditions of triaxial compressive stress. There is generally a marked increase in compressive strength and in ductility. It has been demonstrated that the failure becomes plastic (in a macroscopic sense) at sufficiently high values of confining pressure. Sharp wedge chisel indentation studies conducted by Gnirk and Cheatham indicate that many rocks behave in a plastic manner at relatively low triaxial compressive stress states.4 If "failure" under triaxial compressive conditions is considered to be either complete rupture or macroscopic plastic flow, then the general failure characteristics of a rock can be reasonably well represented by the commonly known Mohr envelope. This certainly is not a perfect failure criterion (since the effect of the intermediate principal stress is neglected) but it has been found to be adequate for most engineering purposes. Mohr envelopes usually are constructed graphically using experimental triaxial test data. For purposes of analysis it is convenient to represent the envelope in equation form. Among the several approximate forms appearing in the literature, a parabolic form is suggested by Cheatham,7 and an exponential form is suggested by Paone and Tandanand.8 The exponential form has been adopted for this study, and based on published data, appropriate parameters have been established for 19 rock types. A typical plot of the data compared with the approximate envelope, and a summary of the rock properties and

Jan 1, 1969

By F. S. Young

Previous laboratory and field experimentation has demonstrated the effect of several variables on drilling rate.1-5 These results have been incorporated into optimization theories6-" for the purpose of reducing drilling cost. Minimum-cost drilling theories rely on a combination of historical data and empirical prediction techniques for selecting optimum bit weight and rotary speed. Past solutions have required extensive use of computing equipment because of both the complexity of the mathematical formulations and the large number of parameters involved. Field attempts to apply these computed results have frequently failed because of the uncertainty of input data requirements. Humble has developed an on-site computer system to control bit weight and rotary speed and thereby implement the concepts of minimum-cost drilling. This system can (1) perform short interval drilling rate tests for formation evaluation, (2) use the results of these tests as input information to solve minimum-cost drilling formulas, and (3) control bit weight and rotary speed in accordance with these computed solutions. The purpose of this paper is to describe the computer control system and present results of initial field testing. Theoretical Considerations Minimum-cost drilling (MCD) requires a quantitative evaluation of the variables involved. Several forms of a basic mathematical model have been sug-gested.'?,' "he relationships reported here form the basis for the solution programmed in this work. Four equations are used, expressing drilling rate, bit bearing wear, bit tooth wear, and cost. A solution for minimum-cost drilling assuming constant bit weight and rotary speed over the entire bit life has been programmed for use in computing MCD schedules. This solution is subject to certain limiting assumptions such as those discussed by Graham et a1.I2: 1. Drilling cost is the summation of bit cost, rotating cost, connection cost and hoisting cost. 2. Diamond bits are excluded. 3. Bit life is limited by either bearing failure or tooth wear, or by a combination of operational factors that make it cheaper to pull an incompletely consumed bit. 4. Circulating hydraulics are adequate and do not limit drilling rate. 5. Bit weight considerations exclude hole deviation. 6. Drilling rate is a function of only bit weight, rotary speed, and degree of tooth dullness; that is, the effects of pressure, lithology, fluid properties hydraulics and drill string dynamics are ignored. In equation form, the four MCD expressions are as follows:

Jan 1, 1970

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham', Eckel' and others .' However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger' led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

By E. A. Hopkin

Laboratory tests conducted by the author. together with actual field experience in Canada. have indicated the magnitudc of some of the factors affecting ability of drilling mud to clean the hole. A correlation was observed between funnel viscosity and particle slip velocity. A relationship was also observed between the Bingham yield value of the mud and the particle .slip velocity. Laburatury tests indicated little change in slip velocity with funnel viscosities up to ahout 80 sec/qt or to yield values of aboul 15 lb/100 .sq ft. The lip velocity of the partic1e.s. studied vuried from 160 ft/min with water to neerly zero for high mud viscositie. lncreasing the mud density, creating laminar annular mud flow or rotating the drill pipe Mlay also improve the carrying capacity of mud. Field tests indicated that during fast upper-hole drilling, the rate of cutting removal must he sufficien to maintain the concentration of cuttings in the annulus at less than 5 percent by volume to prevernt balled-up drill collars and .stuck drill pipe. INTRODUCTION In the Mid-Continent area, hole cleaning during rotary drilling normally involves the use of low-density drilling muds with funnel viscosities varying from 26 to 80 sec/qt. However, frequently it is necessary to raise the mud viscosity in excess of 200 sec/qt to clean the hole. In addition, field experience has indicated that during very fast upper-hole drilling, annular mud velocities considerably in excess of the maximum slip velocity of the cuttings (normally considered to be 120 to 150 ft/min) are necessary to prevent balling the bit and drill collars. In view of these variations in mud properties and circulation rates necessary to clean the wellbore, a study of factors affecting hole cleaning and the relative magnitude of each was undertaken. The study was also prompted by the knowledge that a drilling mud with properties close to those of water would drill at rates several times that of a viscous mud. The carrying capacity of these near-water muds was not clearly understood, however, and many drillers were reluctant to use them. DISCUSSION EFFECT OF MUD PROPERTIES ON DRILLING RATE The effect of mud properties on drilling rate has been studied by a number of investigators. 1t is clear from their work that mud properties close to those of water will significantly improve drilling rate and bit life. If the water-type mud will also effectively clean the hole and cause no logging or formation impairment problems, the choice of an appropriate drilling fluid is clear—use water. Often, however, a water-type drilling fluid is not capable of effectively cleaning the hole. THEORY OF PARTICLE SETTLING The forces acting on a particle that is allowed to settle through a fluid quickly reach equilibrium, and the particle settles at some constant velocity referred to as the slip velocity. The slip velocity of any particle depends upon a number of factors such as density and viscosity of the fluid, the volume, specific gravity, shape and roughness of the particle, and upon the shape and area of the projected face of the particle at right angles to the direction of relative fluid solid movement. Brown' expressed this relationship for spheres in Newtonian fluids in the following equation. where v, = slip velocity D, — diameter of sphere p, = density of spheye p, = density of liquid /a = friction factor g = constant. The friction factor f, varies as the size, shape, surface roughness and slip velocity of the body, and as the density and viscosity of the fluid varies. WaddelV ound experimentally that where dynamic similarity exists. f, was a function of the particle Reynolds number (NRe) of the sphere (Fig. 1). Fig. 1 shows that f, for spheres varies from over 10 for low NKe numbers to 0.44 for N,,. over 600.

By F. J. Schuh

The drilling industry long has been plagued by failures in the bottom few joints of surface and intermediate casing strings. This paper presents an analysis of the various possible causes of failure and concludes that failures are caused by short-lived, high-energy torque impulses delivered from the drill string through the bit while drilling out the cementing plugs, cement and floating equipment. The magnitude of these torque impulses is shown to be a function of the rotational momentum of the drill string, and a method is derived to calculate the magnitude of these impulses. The available methods of strengthening the bottom joints are reviewed. It is concluded that, while present methods are ineffective, a combination of improved procedures for strengthening and minor restrictions on drillout practices will prevent failures. Introduction In most cases, failure in the bottom few joints of casing strings is not discovered until electric logs record that the bottom one, two or three joints have parted from the casing string and slipped down the hole. However, in some cases the parted section of casing uncovers a high-pressure or lost circulation zone, or shifts laterally restricting the passage of drilling equipment. In these instances extensive remedial work is required to realign the parted pieces and seal the exposed formations. Several methods used to strengthen the bottom joints of casing strings include locking set screws in the couplings, putting wedges in special collars, welding straps across the couplings, welding the couplings and, most recently, using epoxy resin-based, thread-locking compounds. Since none of these techniques has eliminated the problem, this study was initiated to find the cause of failures and to evaluate the available methods of prevention. Mechanics of Casing Failures An analysis of the various possible causes of failure indicates that the casing is unscrewed rather than broken and that therefore failure must occur before the shoe is drilled. Since there is no general agreement as to the causes of casing failure, some possible mechanisms were ATLANTIC RICHFIELD CO. DALLAS, TEX. considered in this analysis. Failure of the bottom joints of casing can occur by only one of three types of stress: tension, torsion or bending. The possible mechanisms of failure were evaluated by determining the forces required to cause casing failure by each of the stresses; and, where applicable, the possibility of failure by fatigue was considered. For casing to part under tension requires a downward load of more than the tensile strength of the casing. The lightest API weight H-40 grade casing requires a bit load on the bottom of the casing of 27,000 to 34,000 Ib per inch of bit diameter (Table 1). Since maximum drill collar weights seldom exceed 10,000 Ib per inch of bit diameter, it is apparent that casing strings cannot be parted by the downward load of the drill string. The second mechanism considered was failure by bending. This mechanism requires that the lowermost casing joints be free to be deflected laterally until the bending stress exceeds the strength of the pipe. To fail, the casing (at a height L above the shoe) requires a force and deflection' at the shoe of To deflect the casing shoe with the drill string obviously requires a dog-leg at the casing shoe. This dog-leg must have a rate of change equal to or greater than the change in curvature of the deflected casing, which is given by

Jan 1, 1969

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By M. R. Annis

Drilling mud rheological and gel property changes due to elevated temperatures frequently cause problems in drilling deep wells. A laboratory investigation of the effects of time, temperatures up to 3001; and mud composition on these properties was made with concentric-cylinder, rotational viscometers of the Farm type. The viscometers were sealed from the atmosphere to prevent dehydration of the sample. Gel strengths were found to be more sensitive than viscosities to changes in temperature and mud cornposition. The high-temperature gel strengths of bentonitic clay drilling fluids were not predictable from low-temper.atl4t-e measurements. At high temperatures, [lie clay flocculates. The floccu-lation temperature depends on the concentration and type of solids in the mud and the degree of chemical defloccula-tion. As the bentonite content of a mud increases, floccrrla-tion temperature decreases. Lignosulfonnte treatment raises the flocculation temperature. To minimize adverse high-temperatrrre effects on mud properties, the mud should be maintainted at minimum solids content, properly treated with. a defloccullant which is stable at the maximum ten?perature encountered and maintained at a pH high enough to insure activation of the deflocculant for the duration required. The Methylene Blue Test for cation exchange cnpacity of a clay was found to be a useful guide in deter.niinirig when a mud contains a dangerously high clay conWnt. INTRODUCTION In drilling a well it is desirable, for several reasons, to know the effects of time and temperature on the rheological and gel properties of the drilling fluid in the hole. Problems associated with drilling fluids normally occur down-hole: so it is reasonable to be interested in the properties of drilling fluids at the conditions which exist down-hole. It has long been observed that high pump pressures are often needed to start circulation after a trip and that the "bottom-up" mud that is circulated back to the surface is usually more viscous than it was before "cooking" at the bottom of the hole for several hours. Burk-hardt' showed that a knowledge of rheological proper-ties of muds under down-hole conditions is necessary to predict pressure surges. He showed that the viscosity of a mud greatly influences the magnitude of pressure surges and the likelihood of lost returns. McLean et aL~ showed that the rheological properties of a mud under down-hole conditions are very important to cementing operations. This paper presents data showing the effects of time and temperature on rheological and gel properties of water-base drilling fluids. Measurements of gel strengths and rheological properties were made with two different concentric-cylinder rotational viscometers of the Fann type. One was the conventional six-speed viscometer modified to operate at temperatures up to 350F and at the vapor pressure of the liquid at test temperature. The other viscometer was newly designed to operate at temperatures up to 500F and pressures up to 1,000 psi. Tests with both instruments were made under essentially the same operating conditions. The new viscometer is shown in Fig. I. In this investigation, great emphasis has been placed on the rheological properties of clay suspensions, since clays are largely responsible for a mud's thixotropic and gel-

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Recent efforts to design drilling fluids for increased drifting rates have confirmed some laboratory results of other investigators, but have also produced additional data that should be considered. These data were obtained under controlled test conditions using a microbit drilling machine. Clays and some polymers have previously been reported to cause reduction in drilling rate. Recent data have shown that under laboratory conditions, suspensions of a single day or polymer have sometimes given faster drilling rates than when water was used. Measurements have been made of clay suspensions and polymer suspensions comparing filtration (I) under API conditions, (2) while drilling with temperature of 150F and differential pressure of 1,000 psi and (3) under dynamic conditions after drilling. Some correlation between instanraneous filtration (white drilling) and drilling rate has been observed. INTRODUCTION Several papers have been presented that related drilling fluids to penetration rate. Generally, it was found that a decrease in the solids concentration resulted in significant increases in the drilling rate. Of course, this change also resulted in a decrease in the viscosity of the drilling fluid.' Conclusions from investigations by this laboratory are in agreement. Data have shown that of the simple mud measurements commonly made at the drilling rig (density, plastic viscosity. yield point, API filtrate and total solids), only the density and total solids have a significant relationship to the drilling rate in Berea sandstone when attempting to correlate a single mud property individually.' More recent drilling rate experiments have been designed to study (1) effects of individual clays and polymers on drilling rates in Berea sandstone and Lueders limestone, (2) the relationship between drilling rate and dynamic filtration as measured after drilling and (3) the relationship between drilling rate and dynamic filtration as measured during drilling. Data show that drilling rates are dependent upon type and concentration of particles, type of formation and filtration of the individual fluids while drilling. Mud pressure: pressure of drilling fluid as measured after leaving the drilling chamber (Fig. 1). This is taken to be approximately the mud pressure just past the bit and at the face of the formation. Terrastatic pressure: pressure representing weight of overburden. Formation pressure: pressure of formation fluid as measured at outlet of drilling chamber (Fig. 1). This is taken to be approximately the pressure of fluid in the interstices of the formation. Differential pressure: difference between the mud pressure and formation pressure. LABORATORY EQUIPMENT AND TESTING PROCEDURE The drilling equipment was described in two previous publications."' Main components are a drilling chamber, filter-heater, rotary drive and variable-speed circulating pump. Auxiliary pumps supply pressure boosts for the mud, terrastatic and formation pressures. All equipment is designed for 15,000 psi and 500F. Capacity of the circulating system is approximately 7 gal. The mechanical design was facilitated by moving the rock down onto the bit. Data collected with this design should not differ from that obtained by a normal design where the bit moves into the rock. Drilling fluid is pumped through 50 ft of ID pipe coiled in an oil bath, enters the rotary shaft at a right angle and is pumped through the jets on the bit (Fig. 1). Most of the drilled solids are extracted by a screen mounted in the circulating system on the suction side of the pump. Data reported in this paper were obtained by controlling these parameters: mud pressure, 5,000 psi; formation pressure, 4,000 psi; terrastatic pressure, 5,000 psi; force on bit, 1,000 Ib; formation, Berea sandstone and Lueders limestone; flow rate, 7 gal/rnin; bit, 11/4-in. diameter with two 0.078-in jets; mud temperature. 150F; and rotary speed, 60 rpm. Mud pressure was controlled at 5,000 psi, thus giving a differential pressure of 1,000 psi even though the fluid densities varied. Cores of 3%;-in. diameter and 8 in. long were selected from quarry blocks to provide some control of grain size distribution, permeability and porosity. A 2-in. section was cut off each core and a I -in. diameter plug was taken from this section. Permeability to 5 percent by weight sodium chloride solution was determined and the large cores were

By S. Gstalder, J. Raynal

Consideration was given to simple tests which could be performed on rocks to give a measure of rock drillability. Various methods of breaking rocks were considered and the hardness test developed by Schreiner was selected for this study. The test involves application of an increasing load on the rock face through a flat-faced cylindrical punch until rupture occurs. Test results show that hardness is a good measure of the breaking strength of rocks. Useful relationships are shown to exist between hardness and other physical quantities such as specific disintegration, Young's modulus and sonic velocity. Specific disintegration (volume of rock broken per unit of work input) provides a possible means of comparing the effectiveness of other methods of rock breakage. The relationship between hardness and sonic velocity may be very significant for it may be possible to deduce rock drillability from sonic log data. provided that a mineralogical factor is taken into account. TO test further the results of the work, laboratory drilling tests were performed which closely simulated down-hole pressure conditions. Correlations of drilling results with rock hardness measurements were quite good. It was concluded that rock hardness, as measured in the laboratory or as deduced from sonic logs, could be used in relations for predicting rock drilling performance. INTRODUCTION Drillability of rocks cannot be defined in an absolute manner by a single quantity or measured by a single test. Resistance of rock to drilling depends to a large extent upon the means used for rock destruction. This complicates drillability classification of rocks for there may be as many classifications as there are methods of rock breakage without known functional relations between them. The objective of this work was to develop. in terms of rock destruction behavior, means of selecting the best drilling method for a given rock or the conditions for optimum output from a given drilling method. ANALYSIS OF ROCK DESTRUCTION TESTS Gauthier and Baron' have reviewed the many test methods which have been developed for determining the resistance of rocks to breakage. These include drilling tests, punch tests, scratch tests, resistance to shock, wear tests, etc. A standard drilling test might be to determine the time required to drill a standard depth (1/16 in.) in a rock using a bi-cone microbit (1 1/4-in. diameter) when a standard load (417 Ib) is applied at a standard speed of bit rotation (110 rpm). From the standpoint of similarity, the results of microbit drilling tests would seem to be most representative of the several methods suggested above. However, evaluation of drilling performance by this method is only qualitative and cannot be applied directly to actual drilling conditions. Punch tests basically measure rock hardness. Punches of various shapes and sizes, including small cones for Vickers' and Knoop's tests, the wedge for Epstein's test and the right circular cylinder for Schreiner's test, have been used. Results of these tests lead to a quantitative hardness classification which would seem to be related to the resistance of rock to bit-tooth penetration. Scratch tests are related to the resistance of rocks to abrasion such as would be encountered in drilling with diamonds. Either the width of the scratch obtained at a fixed load or the load required to give a scratch of a fixed width may be used to evaluate surface hardness of the rock. This should be related to the resistance of the rock to wear. The above tests, and probably many others. give relative measurements of the breakage or destruction characteristics of rocks. There is no direct relation between results of these tests and the drillability of rocks. Also, the tests each measure different quantities which have different dimensions and they do not permit direct comparison of numerical values. As one step in rectifying the above difficulties. it is proposed that the results of all test methods be expressed in terms of volume of rock destroyed per unit of work required; this is referred to as "specific disintegration". Test results may then be reported in a form which shows both a classification of rocks in regard to each method and a comparison of methods with regard to each rock. The disadvantage in using specific disintegration is the difficulty of measuring this quantity with accuracy. The volume of rock damage is difficult to measure. as is the true value of work input. Rock heterogeneity adds to the

Jan 1, 1967

By J. G. Bouwkamp

This paper presents three general approaches towards the solution of the stress distribution and the behavior of tubular connections as used in offshore well drilling structures. First, the possibilities of using plastic models and photoelasticity techniques in evaluating the stress distribution in gusset plate connections are analyzed. The results of photoelastic studies on the stress distribution in the in-plane gusset plate of two-dimensional joints are presented. The influence of the configuration of the gusset plate (with and without cut-outs) is discussed. Second, the paper deals with recent developments and applications of computer programs to analyze connections with directly inter-welded tubes and with gusset plates. The possibilities and limitations of these programs are discussed. Stress patterns analyzed with these programs are presented for different joint configurations. Finally, the basic test procedures and results of a test on a tubular joint under static and alternating loads are discussed. INTRODUCTION The effective design of tubular connections as encountered in offshore well drilling towers or floating platforms has been complicated basically by the radial flexibility of the tube walls. This flexibility is a source of severe stress concentrations which can initiate an early failure of these joints. In an attempt to reduce the influence of the wall flexibility of the column tube, certain joints are presently designed by inter-welding the incoming branch members. In those designs, the force acting normal to the chord tube can be reduced considerably. A second group of joints incorporate gusset plates or stiffening rings to stiffen the column wall and to distribute the incoming branch member forces over a larger part of this wall. A third approach to improve the stress distribution in a tubular joint is to increase the wall thickness of the column member. This can be achieved by simply applying a thicker wall section in the vicinity of the joint. A fourth possibility to restrain the radial flexibility of the tube wall is to fill the column member with concrete. Also, a single, cast steel seat welded to the column tube can be used to improve the stress distribution in this wall. Although all these designs improve, in general, the state of stress in the column wall, the altered stiffness often causes the development of critically stressed areas in the web members. At the same time the actual design in most instances is decisively influenced by the site which governs the depth and controls the forces produced by waves, earthquakes and ice flow. Also, the towing, erection and foundation requirements of offshore structures can affect the actual design selection. Because of the complexity of the structural configuration of tubular joints, the stress analysis of these connections has necessarily been based on simplified and often crude assumptions. For the earlier and smaller type of connections with about 4-ft diameter column sections, the primary problem was to evaluate the relative stiffness of the column wall section and the load transfer between joint members. Due to the recent developments of offshore drilling structures with increasingly larger connections (e.g., column diameter. 32 ft; web members, 8.5 ft) this problem has become even more critical. One design philosophy for such large joints follows a member-to-member connection with radially heavy reinforced column sections. This radial stiffness can be attained by closely spaced and intensively stiffened horizontal diaphrams together with vertical stiffeners. A second solution incorporates a concrete-filled section between the outer and inner walls of the column tube. Another philosophy considers large gusset-plated joints. The problem in these joints is to develop an effective load transfer between the branch tubes and the gusset plate and to minimize the stress concentrations in the member walls as effectively as possible. Several concepts are followed to achieve this gradual transfer between web-member walls and gusset plates. Because the number of joints in these huge platforms is limited compared to the over-all size, a proper design of these joints is even more important than was the case for the many joints in the smaller, but multi-legged towers. A failure of one of those ultra-large joints could well cause the complete collapse of such a structure. Under these circumstances an accurate analysis of the large joints is of the greatest importance, together with information regarding the expected behavior of such joints under critical alternating load conditions. Recent applications of photoelastic model techniques have proved to be quite effective in evaluating the elastic behavior of such joints. Although a complete study of such connections is quite well possible with present-day photoelastic techniques, it might often be feasible and necessary to limit the objectives and to restrict these investigations to the study of a specific aspect of the joint. Another very promising avenue of approach to solve the complex stress pattern in these connections seems to be the recent development of digital computer programs. In this category, cylindrical shell programs and finite element methods for more complex configurations have

Jan 1, 1967

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By J. H. Yang, K. E. Gray

Results of single-blow bit-tooth impact tests on saturated rocks under elevated confining pressures and zero pore pressure were reported in a previous publication.1 This paper presents an extension of the earlier work to include a study of crater formation during tooth impact on both gas- and liquid-saturated Berea and Bandera sandstones at elevated confining and pore pressures. The basic data obtained were force-time, displacement-time, velocity-time and force-displacement curves during crater formation. Crater volume was also measured and the mode of crater formation determined. Bit tooth geometry, depth of penetration and velocity of impact were held constant. Results indicate that, with pore fluid present in the rock, failure trends from brittle to ductile as pore pressure is increased at constant confining pressure (pore pressure and borehole pressure were equal) For a given rock type, the mode of crater formation was dependent not only upon the nominal effective stress, but also upon the fluid which saturated the rock pore space. When confining pressure and pore pressure were equal (zero nominal effective stress), bit-tooth impact resulted in brittle failure for nitrogen-saturated Berea, and brittle to transitional failure for nitrogen-saturated Bandera; when saturated with liquid both rocks failed in a ductile manner at zero nominal effective stress. INTRODUCTION Dynamic wedge penetration tests have been conducted by investigators in several fields, but the failure mechanism of rock under dynamic stresses is not understood completely. The complex action of drilling bits, even considering the action of a single tooth, may be considered as a combination of drag bit and rolling cutter action. Thus, as a first step in understanding rock breakage in oil well drilling, single chisel impact and rock planing are of fundamental importance. For example, Gray 2 and Crisp3 studied drag bit cutting action at brittle stress states. Simon4 and Hartman5 studied the reaction of rocks to vertical impact by means of drop tests. The depth of penetration, crater volume and force-vs-time curves during crater formation were observed. The significance of indexing single-bit impacts has been noted.4,6-8 Gamer et al,9 reported impact tests on impermeable Leuders limestone at atmospheric and elevated confining pressures. In all cases the tests were accomplished on dry rock and pore pressure was considered to be zero. The importance of both confining pressure and pore pressure on the failure characteristics of rock was described. 10-12 It was found that the yield strength and ductility of porous rock depend on the state of stress under which the sample is tested. The importance of pore pressure on drilling rate in microbit experiments was noted by Cumingham and Eenink. l3 Robinson 12 also pointed out that in drilling the most important parameter in rock failure is the effective stress, where effective suess is defined as confining pressure pc minus pore pressure pp. The effect of pore pressure and confining pressure on rock strength was also noted by Serdengecti and Boozer 14 in strain rate tests, and by Gardner, Wyllie and Droschackl5 in elastic wave studies. Until recently all reported wedge impact studies under simulated wellbore stress states have been conducted on dry rock. Maurer 16 reported impact tests on samples saturated with deaerated water. Borehole and formation fluid pressures were equal in these tests except when mud was used in the borehole. With mud in the borehole and a high borehole-to-formation fluid pressure differential. Maurer observed "pseudoplastic" crater formation. Podio and Grayl reported impact tests on Berea and Bandera sandstone saturated with pore fluids having wide ranges in viscosities. In Podio and Gray's tests, confining pressure was elevated, but pore pressure and borehole pressure were held fixed at atmospheric pressure. The presence of

By J. B. Cheatham

Applications of the mathematical theory of plasticity promises to lead to the solution of many drilling and rock mechanics problems. ,Because of mathematical considerations, the inelastic behavior of rock has frequently been represented by a perfectly plastic model in conjunction with a yield criteria of the Coulomb or Mohr type. The totality of all stress states for which a solid ceases to behave elastically can be represented as a limit surface in stress space. ,Probing of such limit surfaces indicates details of strain hardening which are not provided by the standard triaxial testing procedure. Probing tests of the limit surfaces have been performed on Cardova Cream limestone to provide data for extending plasticity theory to cover situations in which consolidation and strain hardening are present. Test results indicate that this highly porous limestone undergoes a permanent volume decrease when it is subjected to hydrostatic pressures in excess of 3,500 psi. A virgin sample tested under a confining pressure of 1,500 psi has a yield strength of 1,700 psi; however, if the sample is subjected to a consolidation pressure of 5,000 psi, before testing at 1,500 psi, the yield strength is raised to 2,300 psi. Thus, both consolidation and strain hardening are important considerations in describing the mechanical behavior of this limestone. Tests conducted with the axis of the core having different orientations indicate that this rock is also anisotropic. Portions of the initial and subsequent limit surfaces are determined for samples loaded either perpendicular or parallel to the bedding planes. INTRODUCTION Previous experimental work in rock mechanics indicates that no mathematically tractable constitutive theory is inclusive enough to describe the mechanical behavior exhibited by all types of rocks under all conditions of stress and temperature. Indeed, the type of deformation encountered in a single type of rock is known to depend upon the stress and temperature conditions in the rock during deformation.l-5 Certain rocks and minerals, notably those minerals composed of ionic salts, have been shown to exhibit plastic deformation when tested under conditions of high confining pressure.2 Since the mathematical theory of plasticity provides simplifications over the theory of elasticity in certain types of problems, such as those in which limit analysis can be applied, it is of interest to know under what conditions plasticity theory may be applied to rock mechanics problems. The following factors determine the nature of the deformation a particular specimen will undergo: (1) the microscopic structure of the rock, i.e., the structure visible under an optical microscope, including number of phases, porosity, distribution of phases, (2) the mineralogical structure of the solid phases, (3) the conditions of stress and the rate of change of stress and (4) the temperature. Extensive experiments on Yule marble, Carthage marble, Solenhofen limestone and other calcerous rocks indicate that these relatively nonporous rocks deform plastically under certain conditions of loading, and creep under other conditions of loading.l-3 This study is concerned with the behavior of Cordova Cream limestone (Austin chalk) which is also composed almost entirely of calcite and thus has the same mineralogical composition but, because of a rather large porosity, it possesses a different microscopic structure. This investigation was undertaken to learn if Cordova Cream limestone deforms plastically despite the embrittling effect of the pore spaces, and to provide data which can be used to determine whether the mathematical theory of plasticity can describe the mechanical behavior of Cordova Cream limestone. A brief discussion is given of some of the underlying principles of plasticity theory concerning stress space and limit surfaces. Strain hardening is defined and a discussion is given of how the mechanical behavior of a material can depend on the previous history of the loading. This is followed by a description of the experimental procedures

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard's and Dundrova's theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.' In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By L. R. Raymond

With the trend toward deeper and consequently hotter holes, measurements of drilling mud properties at atmospheric temperatures are becoming increasingly inadequate.' Both the prediction and control of down-hole mud properties depend in part upon our knowledge of temperatures in the wellbore. Consequently, a better understanding of factors that affect temperatures during circulation and trips could improve drilling operations. It was toward the goal of obtaining this understanding that this study was directed. Other investigators2 have studied the response of fluid temperature in the borehole during trips. However, all of these studies have used an assumed formation temperature profile at the conclusion of circulation and have provided no means to calculate this profile directly. In this study, the formation profile during circulation was calculated. Other investiga-tors3-5 have also studied bottom-hole temperature during circulation. However, they have developed neither general techniques for calculating the entire temperature profile in the system nor generalized methods for predicting bottom-hole fluid temperatures during circulation. Such techniques and methods have been developed and are discussed briefly in the following pages. Temperature Behavior During Circulation Circulation of fluid during the drilling operation is represented schematically in Fig. 1. The process of circulation has three distinct phases: (1) fluid enters the drill pipe at the surface and passes down the drill pipe; (2) fluid exits the drill pipe through the bit and enters the annulus at the bottom; and (3) fluid passes up the annulus and exits the annulus at the surface. To simulate the thermal behavior of the fluid in the system, each of the phases of circulation must be described mathematically. In Phase 1, the fluid enters the drill pipe at a specified temperature, TDo. As the fluid passes down the pipe, its temperature is determined by the rate of heat convection down the drill pipe, the rate of heat exchange between the drill pipe and the annulus, and time. Phase 2 of the circulating process merely requires that the fluid temperature at the exit of the drill pipe be the same as the fluid temperature at the entrance of the annulus; i.e., TD(L,t) = TA(L,l). Thus in Phase 3, the fluid enters the annulus at TD(L, t). As the fluid flows up the annulus, its temperature is determined by the rate of heat convection up the annulus, the rate of heat exchange between the annulus and the drill pipe, the rate of heat exchange between the formation adjacent to the annulus and the fluid in the annulus, and time. These rates of heat exchange and the time dependency of mud temperature are described by well known heat-flow equation.6 Consequently, as shown in the Appendix, the temperature profiles in the drill pipe, annulus, and formation can be obtained by solving Eqs. 1 through

Jan 1, 1970