Search Documents

By Jay L. Hodkinson

Replacement of an aging twin span river crossing in Vermont required a temporary bridge to accommodate traffic during construction. Soils beneath the temporary approach embankment consisted of very soft organic clayey silt underlain by interbedded, loose alluvial fine sand and silt/clayey silt. Reinforcement was required for the southern temporary approach embankment to limit settlement and to increase global stability factors of safety. A ground improvement design was developed using Rammed Aggregate Pier® reinforcement and was included in the contract documents as an FHWA Category II Experimental Feature. Instrumentation intended to document the performance of the supported embankment was installed. Piers were then constructed and monitoring commenced as embankment and bridge construction occurred. Weekly instrumentation data reports indicated continuing excess pore water pressure, settlement, and lateral deformation of the subgrade soils as the embankment and temporary bridge abutment was constructed. In response to the unanticipated monitoring results, further investigation indicated that significant deviations from the conditions and basis upon which the ground support design was developed were made during construction. This paper discusses these deviations and their specific impacts to embankment support performance, how these deviations occurred, the role that the ground support system played in maintaining global stability, measures taken to limit further detrimental impacts to the embankment, and provides recommendations for contract document preparation and construction oversight to prevent similar situations from occurring on future projects.

Jan 1, 2011

By Y. Nien Wang

The Devil?s Slide portion of Highway 1 between Pacifica and Montara is often closed due to the instability of the adjacent slopes. Following many years of public input and careful evaluation of alternatives, Devil?s Slide will be by-passed via two inland tunnels, providing a safe, dependable highway between Pacifica and Montara. For the twin tunnels, each 9m diameter tube will accommodate only one traffic lane. Each tunnel tube will accommodate a 3.6 meter roadway, 0.6 meter and 2.4 meter inside and outside shoulders respectively, and 1.2 meter walkways on each side. Cross passages will connect the bores at about 120 meter intervals and jet fans will provide tunnel ventilation. The twin tunnels are approximately 1,250 meter long and 9 meter wide. Excavation will progress from south to north using tunneling techniques that rely on inherent rock strength for support known as the New Austrian Tunneling Method (NATM). Both tunnels will be excavated at the same time, one tunnel face approximately 40 meters ahead of the other. Staggering the tunnels reduces the likelihood of damage from blasting in alternate tunnels. The work schedule is 24 hours a day, 7 days a week resulting in a 24-month timetable to break through to the north portal.

Jan 1, 2008

By Y. C. Kim

An alternate development drilling strategy to the one currently in use at the nine was investigated using geostatistics for a portion of the pit. The study area consisted of 4,000' x 5,000' in plan and 1,080' in elevation. The massive orebody, the three-dimensional nature of the problem, and the location of ultimate pit limit in the study area all created some unique problems in devising the development drilling strategy, as compared to the two-dimensional tabular deposits such as coal deposits. Rather than using the confidence interval of the global reserve estimate as the main criterion for development drilling, the confidence interval of short and medium range mine planning blocks was used as the objective. Based on somewhat arbitrarily selected level of confidence, the results from this study showed that a total of 50 DDHs rather than the planned 62 DDHs is sufficient in the study area, if the selected confidence levels are acceptable to the management. This paper also emphasizes the importance of the particular objectives being used in development drilling and how they influence the "optimai" place- ment of the development drill holes.

Jan 1, 1981

By J. Guha, D. Racicot, S. Peloquin, F. Lange-Brard, S. Bureau, A. Tremblay

The Devlin copper deposit consists of a flat-lying vein and a network of steeply dipping mineralized veinlets hosted by leucotonalite of the Chibougamau Pluton. Most of the vein is enclosed in a hydrothermal breccia zone which has been superimposed on a primary igneous breccia formed during the emplacement of the leucotonalite unit. This igneous breccia contains cognate fragments as well as fragments of the Dore Lake Complex, host rock to the pluton, set in a leucotonalite matrix. The hydrothermal breccia is formed of fragments of leucotonalite and the earlier breccia set in a matrix of finely comminuted rock variously altered in a roughly zonal arrangement. The major ore-bearing structure is the tabular flat-lying vein, varying in thickness from 10 centimetres to 1 metre, with a slight dip to the northeast. Well developed fracture planes, in four major orientations, contain both sulphides and gangue minerals. These appear to be displaced by the flat-lying vein. Late movements affecting the deposit include minor vertical displacements and an east-west shear truncating the southern edge of the vein. Widespread selective alteration of the leucotonalite, followed by multiple alteration veining stages characterize the deposit. Fluid inclusions associated with the mineralization indicate low temperatures, variable salinities with a variety of daughter minerals, and a vapour dominated phase. The fluid shows evidences of boiling at shallow depths. The sequence of events envisaged for the Devlin deposit is a primary brecciation during emplacement of the leucotonalite unit with widespread selective alteration possibly during the cooling stages followed by hydrothermal brecciation and late stage fract uring producing the vertical fractures and the flat-lying vein. From the alteration characteristics and the fluid data it is inferred that the Devlin deposit is the near-surface expression of a porphyry system.

Jan 1, 1984

By Dr. Ralph W. Edie

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By Louis Frost

"Dominion No. 17 Colliery, of the Dominion Coal Company, Limited, is located in the district of New Victoria, N.S., at the entrance to Sydney harbour.This Colliery was opened in 1882 to work a submarine area of the Harbour seam (see Figure 1). It was closed in 1921 and the mine, which has a make of water of approximately 250 gallons per minute, was allowed to fill.No. 18 Colliery, situated almost a mile to the east, was opened in 1938 to work the Phalen seam in this area with the intention, later, of driving a cross-measure tunnel to mine the section of the Harbour seam lying between No. 17 Colliery and the Princess Colliery of the Nova Scotia Steel and Coal Company, Limited.In 1945 it became necessary to open this area in the Harbour seam and a cross-measure tunnel was driven from the existing workings of No. 18 Colliery in the Phalen seam, which underlies the Harbour seam at a depth of 500 feet.The tunnel was started in 1946 and completed in 1948. The cost of opening this section, which contained only 6 1/2 million tons of coal, made imperative the recovery of all the available coal and precluded the maintenance of the large barriers that had been left in No. 17 Colliery for impounding the water, especially as the maintenance of these barriers would have meant the loss of 885,000 tons of coal, or 12.3 per cent of the whole tonnage available. Therefore, a study was made to determine the best means to dewater the 250 million gallons of water lying in the old No. 17 Colliery."

Jan 1, 1952

By Gibson I, Somerville J

Three main confined aquifers occur in interseam sediments beneath the planned excavation for the Loy Yang Brown Coal Open Cut. Sub-artesian groundwater pressures occur in all aquifers necessitating dewatering to prevent excessive seepage and depressurisation to prevent heaving of the open cut floor and batter instability. Reduction of water pressures in coal joints is also required to maintain coal face stability. This paper describes the depressurization and dewatering strategies, investigation for and installation of pump bores and groundwater observation bores. Approximately 5000m of drilling is carried out annually for dewatering at Loy Yang and both cable tool and rotary flush drilling methods are utilized. The cabletool method is used to obtain accurate samples for laboratory analysis, whereas rotary flush methods are used for speed and for installation of the larger diameter pumping bores. A method of re-establishing pump bores after partial excavation during mine development has been successfully developed with large cost savings. Trials are also being conducted with pre-collaring of deep bores with rotary methods then sampling the aquifer strata with a cable tool rig.

Jan 1, 1988

By Abbott T. M

Alcoa of Australia operates three Alumina refineries in the South West of Western Australia at Kwinana adjacent to the South suburbs of Perth and at Pinjarra and Wagerup in rural settings 100 and 150 kilometres south of Perth respectively (see Figure 1). Alcoa's total alumina production is currently around five million tonnes per annum and this will increase to 5.5 million tonnes by early 1990. Further expansion of production is likely if current world aluminium demand trends continue. Alcoa's refineries utilise bauxite mined in the nearby Darling Range which is low grade by world standards having around 32 % by weight extractable alumina (by comparison Weipa bauxite yields around 55% alumina). This means that for every tonne of alumina produced two tonnes of solid wastes remain and therefore while we in Western Australia can boast of hosting the largest alumina industry in the world with around 18% of total world production we suffer from having the lion's share or 40% of the world's bauxite residues to dispose of. In its Western Australian setting the management of these residues in a manner which is acceptable to the community creates many challenges. These are primarily due to the mass and volume of waste produced, its chemical and physical characteristics and the environmental features of the local area including close proximity of neighbours, competing land uses and the presence of natural resources such as surface water and groundwater. In addition the trend towards more stringent statutory environmental controls and greater political and community awareness of environmental issues means that we must be able to demonstrate improvements that will reduce the considerable adverse impacts of past practices. Of course we must also try to keep the overall cost of residue disposal as low as possible to maintain our competitiveness with refineries which may have much smaller volumes of waste to dispose of and less environmental constraints.

Jan 1, 1989

By H. A. Baumann, A. J. Rostosky

EVER since the first installation of wet-washing methods of coal preparation, the removal of the water added by the washing process has created serious technical and operating problems. The rapid development and widespread adoption of wet washing has necessitated a corresponding development of dewatering methods and equipment. The amount of water retained by coal varies with the size of the coal. The moisture that is largely on the surface of the particles is easily shaken off coarse coal; thus coarse coal can be dried comparatively easily and quickly. Fine coal presents a larger surface area than does coarse coal, so its capacity for retaining moisture is greater. In fine coal, moisture below about 5 per cent is held between the coal particles and its removal is difficult. Draining and drying of the finer sizes is a major problem at many washeries. Two common problems of coal-washing practice that are intimately connected with dewatering and drying are the clarification of washery water and the prevention of stream pollution. The first field has been studied from many angles, including the use of coagulating and settling agents followed by vacuum filters to remove the solids, and the use of sludge tanks with dewatering screens incorporated therein. In many districts, the disposal of sludges into streams has been stopped by law. The lack of space for impounding sludges has created problems of disposal in other districts. Reduction in moisture means a saving in freight costs as well as the elimination of difficulties in unloading and storing. Excess moisture in coal causes it to freeze in localities where severe climatic conditions pre¬vail. Excess water in coals to be used in the production of coke and manufactured gas has a chilling effect on the walls of the oven or retort. Dryness of coal is important in producing good briquettes.

Jan 1, 1943

About 3km2 of the central Luise Caldera, in which the Lihir orebody is located, is geothermally active wit.lj gas seeps and fumaroles, and in some areas, a water table at boiling point.The proposed mine, adjacent to Luise Harbor, will be excavated to more than 200m below sea level and will extend into the geothermal system to depths at which current rock temperatures are 170¦C.

Jan 1, 1994

By William M. Phillips

This paper will concern the processing of kaolin clays from the sedimentary deposits of Georgia and South Carolina, While the major processing steps will be touched on briefly, emphasis will be given to the dewatering of the clay-water slurries (slips) formed in the processing of kaolin clays The dewatering steps discussed will include gravity settling, centrifugal dewatering, vacuum filtration, and thermal dryings Of these dewatering steps particular attention will be given to vacuum filtration and the variables affecting filtration of these kaolin clays.

Jan 1, 1962

By Orville R. Lyons

THE removal of moisture from coal has been a coal-preparation problem ever since the first wet-washing preparation plant was placed in operation. Today, when most of the coal produced in the United States is wetted at the working face when mined, or is cleaned by wet methods, the removal of moisture is a necessity for any one or a combination of the following reasons; (1) to avoid freezing difficulties during shipment, (2) to increase the B.t.u. content, (3) to effect savings in freight costs, and (4) to so improve the coal that it may be used for specific purposes-for instance, in the production of briquettes or the production of metallurgical coke-or so that it can be treated by dry cleaning methods. In general, the amount of water retained by coal particles varies with the size-consist of the coal. Fine coal has a larger surface area per unit weight than does coarse coal, so its capacity for retaining moisture is proportionately greater. The removal of moisture from coarse coal is relatively easy, while the removal of water from minus 10-mesh coal or finer is a major problem, usually requiring an individual solution at each preparation plant. As a result, a multitude of methods and a variety of equipment have been designed to solve both general and specific moisture-removal problems. Definitions In order that misunderstanding may be eliminated insofar as possible, it is necessary to define the terms to be used. The moisture content of any given increment of wet, washed coal is made up of two parts, inherent and surface moisture. Inherent moisture has been defined in various ways and as yet no standard definition has been agreed upon. However, in general, it is considered as the moisture that is present in the coal in the bed. The important point to remember is that coal with any amount of inherent moisture, whether 2 or 20 per cent, will appear dry if there is no surface moisture. Also important is the fact that inherent moisture can be removed, in part, by air drying at atmospheric temperatures. Surface moisture is that attached to the surface of the coal particles or that retained in cracks and fissures other than capillary openings in the coal substance. Essentially, insofar as the bituminous coal and anthracite indus-

Jan 1, 1950

By Yuhua Wang, Huilan Yang, Yanqing Jiang, Dongfang Lu

"Generally, the concentration of bauxite flotation tailings is around 10%, a large amount of water in tailings needed to be recycled in the flotation process. Sedimentation and dewatering properties of tailings were investigated under different conditions. Surface high negative charges on mineral particles are the key factor to destroy the settlement of tailings when the pulp pH is around 8.9. Hence, the modification of pulp pH around 7 is necessary to the diminution of the repulsive force between mineral particles and then the acceleration of sedimentation of tailings. Anionic polyacrylamine with molecular weight of 14 million is the best flocculant for the settlement of tailings in all tested polyacrylamines. P-toluene sulfonic acid shows better properties than hydrochloric acid for pulp pH adjustment when anionic polyacrylamine with molecular weight of 14 million is used as flocculant. Although the flotation of diaspore is depressed in the presence of polyacrylamine using sodium oleate as collector, but the recycling water traded by the combination of ployacrylamine and p-touenesulfonic acid does not show the depression effects on the flotation of bauxite ore. The lower residual content of polyacrylamine in recycling water treated by the combination of ployacrylamine and p-touene sulfonic acid plays an important role. INTRODUCTION Generally, the waste water generated from mineral processing plant is usually treated by sedimentation, oxidization, electrodialysis, ions exchange, active carbon adsorption and flotation technology, and the treated water is also used again in the industrial process. Flotation was adopted widely to improve the quality of bauxite from low grade diasporic bauxite in China. For flotation, the grinding fineness of bauxite is over 90% -0.074 mm, sodium carbonate and sodium hexametaphosphate were used as regulators, so the tailings pulp is very difficult to settle and be dewatered (Y. Wang et al., 2004; Y. H. Wang et al., 2007; Wang Yu-hua et al., 2008; Wang Yuhua et al., 2011). The water recycling of bauxite tailings are becoming the highlight for the industrial application of the flotation process for bauxite ore. Researchers in China shift their attentions onto this topic."

Jan 1, 2018

By D Monaghan

Pumping water for dewatering and water supply is a major component of electricity consumption at mining operations and hence is a significant contributor of greenhouse gas emissions. Pump systems at a typical mine site can be broadly split between above ground centrifugal pumps (generally used for water transfer) and submersible borehole pumps (generally for dewatering and/or water supply). In contrast to above ground pumps, submersible borehole pumps can be subjected to varying duty points (total pumping head and flow requirements) as a result of changing bore water levels and yields, particularly in mine dewatering bores. Typically, much higher pumping rates are required at the commencement of dewatering to remove groundwater storage and to intercept sufficient groundwater throughflow to achieve target drawdowns. Once target drawdown levels are reached it often only requires much lower pumping rates to maintain target drawdowns. Pumps sized to remove the large initial volumes of stored groundwater often end up too large for the lower flow rate required for æmaintenance pumpingÆ. This often results in pumps operating inefficiently, a problem which can be made worse when pumps are throttled to reduce the pump output to better match the reduced bore yield. Current standard operating practice places little emphasis on the electricity consumed by pumps, with the focus often being on minimising capital expenditure (æIf it ainÆt broke donÆt fix itÆ). Submersible pumps can have extended service lives of ten to 20+ years. However as the capital cost of a pump typically represents only five per cent of the life cycle cost, the vast majority of the life cycle cost is energy usage.Through the implementation of a regular review of the operation of borehole pumps, significant reductions in electricity use and associated greenhouse gas emissions can be achieved without impacting the dewatering schedule. In most cases, the capital cost of replacing pumps is more than offset by savings in operating costs. These potential savings become even more significant when considering proposed future carbon tax levees.This paper presents examples of the opportunities for significant reductions in energy, greenhouse gas emissions and overall costs that can be achieved for a range of dewatering scenarios.

Jan 1, 2009

By J. E. Nesset

"As an alternative to conventional dewatering by vacuum filtration and oil-fired rotary dryers, Brunswick Mining conducted extensive pilot-scale testwork on its copper, lead, zinc and bulk concentrates using a Larox Oy (Finland) automatic pressure filter. The results showed that pressure filtration readily produced final cake moistures of 6-8.5 per cent on this very fine sulphide material.An in-depth analysis examines pressure filtration in terms of metallurgical performance and projects energy savings of 78 per cent for pressure filters over the current dewatering operation. Potential energy and operating cost reductions are also estimated.IntroductionVacuum filters followed by oil-fired rotary dryers are one of the most common means of dewatering mineral concentrates. They represent, however, a level of technology which is exceedingly wasteful in terms of manpower, space utilization equipment and fossil fuel dependence. In addition, the use of thermal dryers is leading to increased environmental concerns both in plant and out.These were the primary factors which prompted Brunswick Mining to consider alternative dewatering methods as the existing equipment came up for replacement and upgrading. In late 1979, company engineers were encouraged by automatic Larox pressure filters seen at several Scandinavian operations. Subsequent laboratory tests by the manufacturer (Larox Oy of Finland) on several concentrate samples were sufficiently promising for Brunswick and Noranda to lease a trailer mounted filter-lab unit and a technician from Larox for a five-week period. Extensive on-site testwork on all four Brunswick concentrates (zinc, lead, copper and 'bulk' lead-zinc) confirmed the potential of pressure filtration."

Jan 1, 1982

By Robert C. Cifelli

INTRODUCTION Background and Objectives Underground coal mining is a vital component of West Virginia's economy. However adverse environmental effects including ground subsidence and aquifer dewatering are often associated with such mining activities. Many families in northern West Virginia still rely on private water wells and springs for domestic water needs. In such areas where underground coal extraction and land subsidence have occurred, a disruption of the ground water flow system commonly exists with subsequent drainage of water to lower levels that may extent as deep as the mine workings; this causes loss of water supplies to landowners and represents a nuisance to mining companies 2 This report represents a summary of an M. S. thesis project in geology at West Virginia University by the senior author (3). The intent for this study was to document the effects of underground coal removal on ground water levels at selected mine sites in northern West Virginia, as observed from water wells, springs, and streams. This research should be useful to coal companies and regulatory agencies and aid in recommendations of future water well locations and specifications in areas of existing or proposed underground coal mines.

Jan 1, 1986

By J. L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak's potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1983

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980

By Thomas P. Oxford, Leslie G. Bromwell

The waste clay slurry produced during beneficiation of Florida phosphate ore presents a major environmental problem. The large volume of waste requires impoundment in above-ground disposal areas surrounded by earthen dams. As the result of a comprehensive research effort, three approaches to improving clay dewatering involving admixing of sand tailings have been developed. These provide satisfactory performance and appear to be compatible with the technological and economic constraints of the industry. Means of determining waste clay characteristics and analyzing mining waste disposal situations by computer simulation have been devised in support of the planning and field testing effort. Detailed examples demonstrating the applicability of the computer programs are presented.

Jan 1, 1980