Search Documents

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By S. Agatzini-Leonardou

The objective of this work was to prove repeated loading capacities and investigate the selectivity of physically stabilized algal biomass from Spirulina platensis and Chlorella sp. for the removal and recovery of cobalt, nickel and chromium from laterite heap leach liquors. The testwork was carried out on a bench scale in small glass columns and proved that it was possible to immobilize the biomass on the highly porous surface of pumice stone (kissiris). Nickel and cobalt could be removed from pure aqueous solutions of each metal by the immobilized cyanobacterial biomass. Nickel and also cobalt biosorption was sensitive to the initial solution pH. Cobalt recoveries up to 80% were achieved after 5 loading cycles, from low concentration solutions, at pH 6.0. Nickel removal was complete under the same conditions, whereas chromium sorption was ineffective. Desorption of the metal loaded columns was effected by dilute sulfuric acid. The algal species giving the best adsorption capacities for the metals under consideration was selected for further experimental work with real laterite heap leach solution produced by column leaching. A statistical analysis of all obtained results was conducted using the fraction of metal removed as response. The ratio "mass of metal removed to mass of protein contained in the immobilized cells" was determined as well. The described method might be applicable for recovery of cobalt and nickel from diluted laterite heap leach solutions, such as heap wash waters, or for their removal from waste streams of a hydrometallurgical extraction process.

Jan 1, 1997

By Yasuo Ojima

A new copper continuous converting process was investigated to evaluate the possibility of its application in the commercial operation. The tests were performed both in the laboratory and in pilot plant scale. Bath smelting process with the use of the top submerged lance technology was applied in these tests. Furnace shape was modified to a lengthwise eylindrical one with a settling area. The furnace monitor was put in the settling area to check the furnace from inside, FeOx-Si02, FeOx-CaO and FeOx-CaO-Si02 based slag systems were used to check their efficiency, The optimum slag chemistry to have good metallurgical results was discussed and FeOx-CaO system with some Si02 content turned out to be preferable although it has not been practically used, In this pilot plant test feeding rate of I tIH of solid grain matte was charged consecutively for two weeks and continuous converting could be done successively. This process is expected to overcome the problems of existing processes and be easily applied in existing plants.

Jan 1, 2003

By J. Lui

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300?C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination ofH2S and uptake buildup.

Jan 1, 2003

By Nicolas Reynier

The separation of radionuclide during rare earth element (REE) production is an important requirement for developing the Canadian REE mining industry. Separation of actinides from REE is often a large concern in the rare earth industry because of the need to manage the radioactive nuclides. A patented process developed for actinides extraction from radioactive wastes was applied to REE ore. Objectives were to optimize the process for REE leaching from ore, and separate radioactive impurities from sulphuric and nitric liquor by ion exchange (IX). Ore leaching was optimized using a surface response plan to ensure statistical significance. In optimized conditions, solubilization yields ranged from 90–95% for Th, 60–75% for U, 48–55% for LREE, and 59–75% for HREE in sulphuric and nitric media. Both media were compared for radionuclide removal from rich REE-bearing mineral liquor by IX. Actinides separation ranged from 92–97% for Th and 69–96% for U in sulphuric and nitric media.

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988

By Peter Stiaszny, Andrej Samoilov, Yuri Titovets, Gottfried Hribernig, Nikolai Zolotorevskii

"The model has been developed to simultaneously predict both transformation product portions and mean ferrite grain size from the same common · principles as a result of the austenite decomposition during any cooling path of dual phase steels. The transformation products considered are polygonal ferrite, pearlite, bainite and martensite. The model is based on the classical equations of nucleation-growth theory and also contains some empirical parameters. The chemical driving forces for nucleation and composition of elements at the phase interfaces are derived by computation thermodynamics. The empirical parameters related to the model were determined on the basis of a series of austenite transformation dilatometric curves and grain size measurements for continuous and interrupted cooling of several steel types. The model is aimed to predict phase transformation in the complex cooling conditions of the run-out table of the hot strip mill at YOEST-ALPINE STAHL LINZ GmbH as a part of the computer aided system for prediction and on-line controlling of the mechanical properties of hot-rolled strip.IntroductionThe term ""dual phase steels"" is used to refer to a steel consisting essentially of a dispersion of martensite in a fine-grained ferrite matrix. These steels are of increasing technological interest since they provide a better combination of strength and ductility than any other conventional steel sheet material. The strength is important because it offers an opportunity to produce lighter components, while good ductility is needed to permit easy forming of components. It is generally recognized that martensite plays an important role in determining the strength level of dual phase steels. A full understanding of the role played by the phases in determining such characteristics requires investigating in more detail how to optimize the martensite level of such steels, while maintaining good ductility remains the subject of continued research in the industry."

Jan 1, 2000

By Pengqi Zhang, Mingcheng Bing, Lixiong Shao, Shuxing Qiu, Qingyun Zhang, Shengfu Zhang

Coal desulfurization has been regarded as an effective pretreatment for clean fuel and less environmental pollution. The microwave irradiation was used to desulfurize the Nantong coal leached with H2O2 and NaOH. The results showed the desulfurization rate of the coal is very low by directly microwave irradiation, while the coal samples leached with H2O2 and NaOH by microwave irradiation could effectively improve the desulfurization rate. The optimum desulfurization conditions were obtained as 10-min irradiation time, 800 W irradiation power, particle size below 74 μm, 1:1 concentration ratio of H2O2:NaOH, in which the desulfurization rate reached 51.14% of the total sulfur content. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra of coals structure before and after treatment have shown the bands in both coals changed slightly except the relative intensity of some absorption ones. It can be found that most of FeS2 and –S–S– functional groups transferred after treatment, while –SH and –S=O– had almost no changing by ATR-FTIR spectra analysis. The structures of coal matrix would not be broken by microwave irradiation in reasonable the reaction conditions.

Mar 1, 2017

By Chikabumi Yamauchi

The comprehensive scientific development of conventional industrial technologies stimulates the creation of new ones in the next generation. Prof. Akira Yazawa has just accomplished such an important work in the non-ferrous pyrometallurgical field. The results of his successful research are immortal. The research group of the author has conducted since 1985 fundamental studies on the application of sodium carbonate slag to copper fire refining. In the present paper, a calculation method for the distribution ratios of impurity elements between sodium carbonate slag and molten copper will be shown. The specific treatment by sodium carbonate slag will also be presented as an effective way for reducing each impurity content in the molten copper to 0.1 mass ppm, which is the level required for the production of high purity copper. The thinking-out of this evaluation method gets a hint from the Equation (2) in the text which was proposed by Prof. Akira Yazawa.

Jan 1, 2003

Equilibrium calculational software programs can be effectively utilized to illustrate the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation to students studying hydrometallurgy. The calculational program STABCAL will be demonstrated. illustrative examples for the creation of diagrams such as EH-pH, activity or concentration-pH and activity or concentration-EH will be presented to demonstrate the fundamentals of real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Applications will include treatment of Acid Mine Drainage (Berkeley Pitlake water and sediments), mass balance potential/pH diagrams, leaching and selective separation of metals from electroplating sludge, metal adsorption at femhydrite surfaces, and flowsheet development for treating mercury sulfide K106 sludge.

Jan 1, 2002

By Youn-Bae Kang, Jong-Jin Pak, Min-Kyu Paek

The critical evaluation and thermodynamic optimization of Mn-Si-C and its sub-binary systems have been carried out over the whole composition range from room temperature to above the liquidus temperature. The solution properties of the liquid systems have not been clearly described because the liquid solution exhibits a high degree of short-range-ordering. In order to predict the thermodynamics of the liquid solution, the liquid phases were optimized by the modified quasichemical model. The model parameters of the solid phases were also optimized by the compound energy formalism to best reproduce the phase diagram and important thermodynamic properties in Mn-Si-C system. Using the model parameters, various thermodynamic calculations were carried out. The present database will be a part of larger thermodynamic database for the ferromanganese alloy database.

Jan 1, 2014

By Lin Zhu, Zheng Wei, Meng Li, Xueli Cao, Hanying Wen, Guodong Shi, Lei Yu, Wen-xin Tang, Tao Li

Low energy electron microscopy and photoemission electron microscopy (LEEM/PEEM), as powerful in-situ surface-sensitive electron microscopy, find wide applications in surface physics, chemistry and catalysis. The high reflectivity of incident low-energy electrons (0–100 eV), allows it to image the surface structures in the topmost few atomic layers within less than one second, while the sample can be heated up to 1200 °C in real time which is potentially very useful in metallurgy and materials fields. A unique three-prism aberration correction (ac-) LEEM was commissioned successfully in Chongqing University, with a lateral resolution below 2 nm. A multiple gas source in the ac-LEEM system was installed as well, which allowed us to observe chemical reactions of nanoscale mineral powders on metallic substrates. In this paper, the latest results on the applications of this three-prism ac-LEEM on oxidation and reduction processes on copper and iron polycrystalline surfaces are demonstrated.

Mar 1, 2018

By Joseph Bloch

The hydriding of bulk metals and alloys is a gas-solid reaction in which a hydride product layer is initially nucleated adjacent to the gas-solid interface and continues to grow until a complete transformation of the parent (a) phase into the hydride phase. The combination of measurements of the overall hydriding kinetics of samples having defined shapes and dimensions, together with examinations of partially hydrided samples, enables the presentation of the reaction rate in terms of an appropriate reaction model. A common and important type of topochemical development of the hydride in bulk metals and alloys involves a hydride layer formed on the metallic surface. The continuity of the layer can affect the reaction rate. The rate of hydrogen absorption in a sample, in the presence of a hydride layer, is usually analyzed using a model combining several sequential steps in which the hydrogen is transferred from the gas phase into the reaction site. Coupling the flux equations across the layer under proper steady state conditions, results in a complex rate equation in which the steady state rate of hydrogen absorption (proportional to the hydride layer velocity) is expressed in terms of the pressure, temperature, the rate constants of the sequential steps and the critical concentrations of hydrogen in the hydride. Generally, the rate constants of the individual microscopic processes are comparable in magnitude, so that the overall rate is not controlled by any of the specific sequential steps. However, there are two limit cases related to the first stage, the adsorption, for which the general rate equation is much simpler, namely, the fast and the slow adsorption approximations. Using this limit cases, equations are derived for the steady state hydriding rate of a given system. These equations provide means to anticipate the pressure dependence of the steady state absorption rate under low pressures, close to Peq and under very high pressures. At the low pressure regime both the fast and slow absorption cases yield linear pressure dependence. For the very high pressure range, it is found that the rate become independent of the applied pressure. The rate is given then by a combination of the individual rate constants of the system and the critical hydrogen concentrations. The model is shown to apply in several real cases, such as ZrCo, LaNi5 and titanium.

Jan 1, 2002

By Toshiaki Akahoshi

Keywords: Wasted catalyst, Hydrodesulfurization, Ammonium vanadate, Ammonium molyb-date, Hydrometallurgical process. The fundamental reactions have been investigated in order to develop a hydrometallurgical process for recovery of molybdenum and vanadium from wasted catalysts generated in the hy-drotreating desulfurization of heavy oil. The principal steps of the process are a mild oxidation roasting of the waste catalysts at temperature around 500°C, leaching of the target metal components with dilute ammoniacal aqueous leachates, selective precipitation of vanadic acid, and ammonium molybdate precipitation. The selective recovery of vanadium as vanadic acid is successfully performed using ammonium sulfate as a salting-out agent. Recovery of ammonium molybdate is based on large dependence of solubility of ammonium molybdate in ammoniacal solutions upon temperature and ammonium salt concentration. In this process, the solution after recovery of vanadium and molybdenum is recycled to the leaching stage of the roasted materials, and the ammonium salts in the process liquor is in the repeated use. Employment of am-moniacal system makes it possible to operate the roasting at much lower temperature than that for the currently operating process.

Jan 1, 2005

By S. Chama, K. Nyirenda, J. Machona, P. W. Chishimba, S. Parirenyatwa, G. Kaluba, Y. R. S. Hara, D. M. Musowoya

Our study focuses on upgrading of copper and cobalt from the Democratic Republic of Congo tailings, containing 2 wt% Cu and 0.5 wt% Co. Cobalt is in the complex iron silicate matrix such that its recovery by direct leaching is not possible. Two concentrating methods were employed in order to obtain copper and cobalt concentrates. Copper was concentrated via flotation and, at the optimal conditions its grade in the concentrate was 31.9 wt%. Cobalt was concentrated to 8.6 wt% b ycarbothermically reducing the flotation tailings with coal in a temperature range of 800–1050 °C and followed by magnetic separation. The reaction products were analysed by atomic absorption spectrometer (AAS) and scanning electron microscopy (SEM) techniques. The best carbothermic reduction temperature was found to be 950 °C due to maximum metallisation and less sintering between gangue and metallic/alloy phases.

Mar 1, 2017

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By P. Heald-Wetlaufer

Doubly polished sections (i.e., sections polished on both sides) allow insights into complex paragenetic relationships, the interpretation of which is essential to understanding ore-forming processes. Alternate viewing of these optically superior sections in transmitted and. reflected light facilitates the recognition and definition of growth zones in ore and gangue minerals and the interpretation of postdepositional changes, such as hydrothermal leaching and replacement. Many such observations would escape detection by conventional petrographic methods. Our procedure for preparing doubly polished sections has evolved during the past 20 years and incorporates many standard procedures. Studies from such diverse districts as Creede, Colorado, Hokuroku, Japan, and the Upper Mississippi Valley zinc-lead district, southwestern Wisconsin, demonstrate the value of observations from doubly polished sections in constructing genetic models. The advent of doubly polished sections represents a major advance in the study of ore deposits and they should be a standard tool in every ore petrology laboratory.

Jan 1, 1982

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By Feng Gao

A general unsteady- state model, based on a cracked substrate, has been developed to account for reaction and diffusion within porous substrate during oxidation of Carbon Fiber Reinforced Carbon matrix (CIC) composites. The effects of several parameters, such as diffusion and reaction rate ratio, oxygen concentration, and composite density, on oxidation process are explored. Also, theoretical results for a set of parameter values of the CIC composites are compared with experimental data. It shows that the model predicted values agreed well with the experimental data in weight loss. Based on this model, quantitative predictions of oxidation of a composite with cracked substrate can be made.

Jan 1, 1993

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993