Search Documents

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By Guangqing Zhang

The paper presents results of a systematic study of synthesis of titanium oxycarbide and its chlorination. Titanium oxycarbide was produced by carbothermal reduction of titania in hydrogen, argon and helium. Formation of titanium oxycarbide started at 1200°C in all gases. The reduction was the fastest in hydrogen. Formation of titanium oxycarbide in hydrogen was close to completion in 120 min at 1300°C, 60 min at 1400°C and less than 30 min at 1500°C. Reduction in argon and helium progressed at a similar rate and reached 90-95% after 300 min at 1400-1500°C. The chlorination of titanium oxycarbide was ignited at 150-200°C. Chlorine partial pressure and gas flow rate strongly affected the chlorination rate. Chlorination of titanium oxycarbide produced with carbon to titania molar ratio 2.5 at 235-400°C was close to 100% in 30 min.

Jan 1, 2009

By N. Kanari

One of the criteria to define the market value of chromite concentrate is its chromium to iron ratio. Changing this ratio for a definite chromite mineral is impossible by physical processing. This study investigated the possibility of increasing this ratio through the carbochlorination and the oxychlorination of chromite concentrates. Experiments are carried out up to 1000 °C. The characteristics of samples and reaction products are determined by SEM, XRD and chemical analysis. The carbochlorination of a chromite concentrate at about 600 °C leads to the . selective partial elimination of iron allowing a higher Cr/Fe ratio of the treated concentrate. Selective extraction of iron could also be achieved at about 950 °C by oxychlorination. In this case, a part of chromium contained in the concentrate is recovered as chromium oxychloride. The obtained residue had high content of Cr, Mg and A1 oxides. Such material has probably better chemical and thermal properties that may. be useful for foundary and refractory applications. Two flow-sheets for the beneficiation of the chromite concentrates using carho- and oxychlorination are suggested.

Jan 1, 1997

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By Toshiyuki Kawai

Copper concentrate smelting directly in P-S converters was started at Onahama Smelter in 1983. Thereafter, the tonnage of concentrate smelted through the P-S converters increased, such that by 2002, it equaled the tonnage smelted through the reverberatory furnaces. In 2003, 56% of the total copper concentrates treated at Onahama Smelter were processed directly through the P-S converters. Technical improvements are reviewed and advantages of direct smelting in P-S converters are reported.

Jan 1, 2005

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Wen-Ming Chien

Keywords: AN-KN Phase Transition, Lattice Parameters of AN-KN, X-ray Diffraction The lattice parameters of the low and high temperature phase of KNO3-rich (in NH4NO3) solid solutions have been determined by the X-ray diffraction method. The low temperature single KNO3 phase (KN II) are from 92%-100% KNO3 in NH4NO3 composition range and from room temperature to 393 K showing in X-ray diffraction patterns. The high temperature KNO3 phase (KN I) showed very broad composition range between 20% to 100% KNO3. The lattice parameters of KNO3-rich (KN II and KN I) solid solutions have been calculated at different temperature range. The volumes of orthorhombic KN II phase decrease from 0.3208(3) to 0.3195(3) nm³ at the room temperature as the compositions increase from 95% to 100% KNO3. The lattice constants of the hexagonal KN I phase show that there is no significant change in a-direction when the temperature increases. Details X-ray results and lattice expansion equations during heating will be presented.

Jan 1, 2005

By Theo Lehner

Turning matte into anodes continues to be an area to watch: for visitors to see pyrometallurgy in action; for metallurgists to keep up with modern smelting furnaces and ever increasing production rates; for management to remain profitable using more tools than taught in school; and for environmentalists to detect the last small clouds from the ever cleaner smelter. Current converting practices have been screened and analyzed, and today, converting and casting is a modern industry. An impressive, though typical learning curve of converter productivity may be detected. Local conditions such as availability and type of raw materials, products extracted, cost factors, etc., have stimulated the development of add-ons or even alternatives to the still dominant method of converting by Peirce-Smith technology. Turning blister copper into anodes follows a similar path, namely increased productivity and improved quality. We dare to predict that development will continue.

Jan 1, 2005

By Emma Arakelova

An increase in concentration of a Zn-containing volatile complex for synthesis of ZnO films was investigated when processing their target by ultraviolet radiation emitted by mercury lamp. The experiments were carried out using a flow-type quartz reactor. ZnO tableted target was preliminarily irradiated during 2 to 7 hours. H2O2 (98%) vapor at 25Pa passed through the reactor with ZnO target at 373K. As substrate material, five subsequent quartz cylinders were used at 423K. The experiment lasts 4 hours. H2O2 decomposition on ZnO surface was accompanied by formation of a Zn-containing volatile complex which passed in gas phase and decomposed on the substrates with isolation of final ZnO. The concentration of the Zn-containing volatile complex (N) in gas phase increases with UV pre-irradiation time (t) (without irradiation N = 1.05 1011 particles/cm3; after t=2 hours, N = 5.19 1011 particles/cm3, after t=4 hours, N = 9.95 1011 particles/cm3; after t=7 hours, N = 1.86 1012 particles/cm3.

Jan 1, 2006

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By Don Ibana

Supported by the Minerals Council of Australia (MCA) through the Minerals Tertiary Education Council (MTEC), three Australian universities–Curtin University, Murdoch University and the University of Queensland–have formed the Metallurgical Education Partnership (MEP) to jointly develop and deliver an engineering design capstone unit–Metallurgical Process and Plant Design–in their respective undergraduate programs in extractive metallurgy, in order to enhance the students’ educational experience. A unique feature of the program is the close interaction of the students in all three universities and a significant involvement of industry professionals. Now in its sixth year, it is clear that this unit is achieving its objectives

Jan 1, 2014

By Pier-Lorenzo Solari, Philippe Moisy, Michel Schlegel, Stephane Pellet-Rostaing, Eric Mendes, David Bengio, Richard Husar, Thomas Dumas

Ionic liquids (ILs) are molten salts composed of an organic cation that are liquid below 100 °C. They demonstrate unique physico-chemical properties such as good conductivity, negligible vapor pressure and non-flammability. As a consequence, they are often regarded as green solvents and could become an alternative to the use of both high-temperature molten salts and volatile organic solvents in rare-earth elements processing and recycling. The diversity of interactions existing in an ionic liquid allows the solubilization of both polar and apolar compounds. Moreover, coordinating functions on their composing ions can lead to stabilization of some species. For instance, in non-aqueous media, europium exists in the (II) oxidation state which is not stable in aqueous solutions. Understanding the mechanism of Eu(III) electrochemical reduction to Eu(II) and the stabilization of Eu(II) species in IL media could be of major interest for the development of innovative recycling processes. Using transient electrochemistry and UV-Vis spectroscopy we could get valuable information on the redox behavior of the Eu(III)/(II) couple in the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([EMIm][NTf2]). Reduction of Eu(III) to Eu(II) and stability of Eu(II) was also studied thanks to a XAS-spectroelectrochemistry set up used to follow in situ the evolution of the XANES spectrum around the L3 edge of Eu during electrolysis.

Mar 1, 2018

Sm-Co alloy is a kind of magnetic material with high power and has been applied in modern industry widely. In this study, the wet chemical co-precipitation was developed for synthesis of the Sm-Co alloy oxide precursor. The thermodynamic analysis of the studied system was done to clarify the solution behavior theoretically based on the thermodynamic equilibrium and simultaneous equilibrium. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH, reactant concentration, dispersant, reaction temperature and time, etc. It is found that by precise control of the process, the Sm-Co alloy oxide precursor was synthesized with fine crystallization and special size & size distribution.

Jan 1, 2005

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009