Search Documents

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By Xia Lou, Hossein Dashti

Gas hydrates technology has been considered as an alternative method for carbon dioxide (CO2) separation. A wide range of studies have been reported in the past decade on the improvement of the separation efficiency by using chemical additives. While most of these studies have shown improved kinetics, thermodynamics and/or separation efficiency at the laboratory scale, there has been no quantitative analysis of the energy consumption for viable industrial applications. Comparison of the effectiveness of the chemical additives from separate studies or groups also is impossible. The present work is focused on the modelling of the hydrate-based CO2 separation process and provides a quantitative approach that is new in its analysis of the effectiveness of chemical additives in relation to the energy required and the kinetic parameters involved in the process.

Mar 1, 2018

By Hu Meilong, Liu Lu, Bai Chenguang

Extracting perovskite from high titanium-bearing blast furnace (BF) slag is a green and potential method to recover the second titanium resource. The non-isothermal crystallization process of perovskite in synthesized high titanium-bearing slag was studied in situ by confocal scanning laser microscope (CSLM) with cooling rate of 20 K/min. The results showed that perovskite was the primary phase formed during cooling process in the titanium-bearing synthesized slag (TiO2=23%). Perovskite started to precipitate at 1719 K and finally presented an orthogonal straight lines morphology.

Jan 1, 2014

By Lucas de A. Pontes, Lázaro A. Rohen, F. V. Carlos Maurício, Janaina da Silva Vieira, Sergio Monteiro, Dhyemila de P. Mantovani, Frederico M. Margem, Anna C. C. Neves

The lower density of the lignocellulosic fibers such as the hemp fibers and the other natural ones is one of the characteristics that allow the scientists to obtain high levels of specific properties that when compared to the properties of ordinary reinforcements gives to the hemp fibers an advantage as a material with an expressive potential in the mechanical properties area. Then, the aim of this present work is to characterize the relative density of the hemp fiber related to the water using the pycnometry technique. This technique uses the pycnometer and it is divided in two steps. In the first step the correction factor and the moisture content of the fresh hemp fiber specimen and in the other step some weightings were done such as the dry specimen (g), empty pycnometer (g), pycnometer + water (g) and pycnometer + water + specimen (g) using a digital balance with a precision scale of 0.001 g of the bran INNERSCAN. Based on these measurement and calculations using some formulations already established in previous studies, the relative density of the hemp fiber found was around 1.393 g/cm3 and the moisture content around 7.1%.

Mar 1, 2017

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By T. Fujita

The removal of phosphorus is essential 1n order to increase the recycling of steelmaking slags for their manganese, iron and lime contents. This study aims at establishing the phosphorus mineralogy and its distribution in steelmaking slags, the effect of slow cooling, and the methods of phosphorus removal. A series of steelmaking slag samples was prepared at different cooling rates, and the mineralogy, chemistry and grain size of the samples were investigated with SEM/EDS and x-ray diffraction. The test results using high gradient magnetic separation are discussed.

Jan 1, 1988

By Reimers. Jan H.

Practically all the world's lead is produced by sintering and blast furnace smelting, or the Imperial Smelting Process which is a variant of the blast furnace process. Increased coke and labour costs and strict lead emission limits have, however, made blast furnace smelting undesirable in most countries. A change-over to other lead smelting processes providing better working conditions and lower emissions is, therefore,. expected to occur once economic conditions improve and the necessary capital expenditures can be justified. The need for new lead smelting processes has long been evident and a number of new processes have been proposed 'and advanced to various stages of development. One of the new processes is already proven on commercial scale, while several others are still being tested on pilot plant scale.

Jan 1, 1983

By Liu Chunpeng

The new technological process developed is by means of thermal plasma arc smelting to obtain high grade Ni matte directly from Ni-Cu concentrates containing 6-7% nickel and 3-8% sulfur. In comparising with conventional smelting and converting processes the plasma arc smelting process has many advantages over conventional processes, such as lower energy consumption, lower capital investment and free from SO, pollution by transforming the sulfides into elemental sulfur with microwave irradiation under controlled oxygen potential, moreover, the process is simple and easily controlled due to less magnetite troubles in the operation. Therefore, this new technological process can be used as an alternative way to conventional process for Ni-Cu concentrate smelting. The main economical technical index is summarized in Tabal 1. Table 1 Main Ecnomic-technical Index

Jan 1, 1993

By Xie Hao

According to its raw materials orthogonal test scheme is designed and a large number of systemic experiments were carried out in order to study the sintering characteristics of three types of fine ores in Kunming Iron&Steel Co.Ltd(KISC). The effects of carbon mixture ratio and basicity on sintering time, agglomeration ratio, physical properties and utilize coefficient were researched via single factor analysis and range analysis. The experimental results show the best mixture ratio of each fine ore. Analysis found that the influence of the carbon mixture ratio is more significant than which of the basicity on the sintering process except agglomeration ratio of foreign ore.

Jan 1, 2009

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thennodynamics, kineties and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thennodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thennal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003

By Hu Long

In this, the first systematic study of the oxidation of orpiment (As2S3) in sulfuric acid solution under oxygen pressure at temperatures above 170°C, the effects of retention time, temperature, particle size, oxygen partial pressure, the concentration of sulfuric acid and pulp density were evaluated. The effects of cupric and ferric ions on the oxidation rate of As(III) to As(V) were also examined. The products of oxidation are As(III), As(V), SO42- and elemental sulfur. At temperatures ranging from 170 to 230°C, most of the arsenic was found to be in the trivalent state, and oxidation to As(V) with oxygen was very slow. This was confirmed by attempting to oxidize a synthetic arsenious solution. However, the rate of oxidation of As(III) to As(V) is rapid in the presence of ferric ion. Elemental sulfur was found at all temperatures investigated, which can be further oxidized to sulfate at high temperature.

Jan 1, 1999

By U B. Pal

Downsizing and decommissioning of nuclear facility operations is increasing the stockpile of various different grades of Radioactive Scrap Iron (RSI). Disposal of this material not only represents significant resource and value lost, but also necessitates long term monitoring for environmental compliance. The latter results in additional recurring expense. It is desirable to be able to decontaminate the RSI to a very low level that can be recycled or used for fabrication of containers for RSI disposal instead of using virgin metal to fabricate the container. Electro-Slag Remelting and Refining (ESR) is often used for decontaminating radioactive contaminated sources of scrap iron such as stainless steel. Non-radioactive oxides of cerium are used to simulate the radioactive oxide contaminants of Uranium and Plutonium. The success of the ESR process is strongly dependent on the capacity of the slag to rapidly incorporate the radioactive contaminant (simulant). In this study we have measured the slag-metal partition coefficient for cerium and investigated the reaction mechanism for the dissolution CeO, in the slag.

Jan 1, 2002

By Ari Jokilaakso, Dmitry Sukhomlinov, Keiran Holland, Pekka Taskinen, Ville Naakka

This study is focused on distribution of Co, Ni, Ag, Au, and Pd between molten copper and molten copper sulfide (‘white metal’) phases in copper converting conditions. The behavior of the elements selected was studied experimentally at 1300 °C and at various sulfur dioxide partial pressures (0.01, 0.05, 0.1, 0.5, and 1 atm). The experimental technique employed involves a high temperature equilibration followed by rapid quenching in ice water, with subsequent quantitative elemental analysis of the equilibrium phases with an electron micro probe analyzer. The distribution coefficients LCu=wm Me determined in this work can be arranged in the following sequence: Co < Ag < Ni < (Au, Pd).

Mar 1, 2018

By M. Omneya El-Hussaini, M. Galal Abdel Wahab, A. Mohamed Mahdy, M. Fathi El Shahat

"Um-Gheig Pb-Zn representative sample was collected from the main adite of Um-Gheig mine along Red Sea coast in Egypt. Its chemical analysis shows that, it contains 16% Zn, 2.3% Pb, 0.1% Cd and 0.1% B as elements of interest. After H2SO4 agitation leaching, the chemical composition of Um- Gheig Pb-Zn deposit ore residue assayed 2.26% Pb, 1.5% Zn, 0.085 % B and 0.01% Cd. This residue was leached with 20% HCl at S/L ratio 1/3 for 2 hours at 80o C. The chloride leach liquor was found to contain 18 g/l Pb, 13 g/l Zn, 0.1 g/l Cd and 0.75 g/l B with the corresponding leaching efficiencies 79%, 86%, 100% and 88% respectively. Lead was precipitated from the chloride leach liquor using concentrated H2SO4 to obtain PbSO4 with precipitation efficiency 96%. While boron was extracted by the selective resin Amberlite IRA743 with loading efficiency of 80%. On the other hand, Zn and Cd were precipitated using Na2S solution with 86.7% and 100% recovery efficiencies respectively.IntroductionLead-zinc ores occur in Egypt in a few localities distributed along the Red Sea coast between El Qusier and Ras Banas.. The reserve of the ore deposits has been estimated by Soviet and German Experts to be about 900,000 Ton, [1]. Onal et al., [2] recovered Pb from Pb–Zn sample containing 10.17 % Pb and 10.98 % Zn from Aladag in Turkey. El-Sherif, [3] used concentrated HCl to leach lead-zinc ore sample of Um-Sammuki area in Egypt. As had been published by Marchioretto et al. [4], the precipitation of heavy metals with lime, sulfide and caustic soda are the most commonly used economical methods for metal removal. Lead was completely removed from the anaerobically digested sludge by precipitation with NaOH and Na2S at waste water treatment plants. Mahdy et al., [5] had successfully extracted boron from the bittern solution of Qaron Lake by ion exchange resin (Amberlite IRA 743). The extraction of boron was mainly depending upon the pH value. They extracted 80% of boron at pH 5.5, while at pH 3.9 about 74% boron was extracted. Kabay et al. [6] used the column-mode to remove 1g/l of boron from geothermal waste water of the Kizildere-Geothermal Power Station by using Diaion CRB 02 Nglucamine- type chelating resins. In this regard, the removal of lead, cadmium and boron allow the residue to be reclassified as non hazardous material."

Jan 1, 2008

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By J. W. Perez

Raw coal will often break intragranularly in either a completely random way or in a differential mode where one species will have a different rate of breakage than another. Locked coal-ash and coal-pyrite particles can also break by the preferential detachment of one species from another along zones of inherent weakness in locked particle assemblages. The mode. cf breakage is largely a function of the nature of the feed, but it is also influenced by the comminution device and the operating variables. Evidence of breakage of particles in the various modes is seen in the crushing of raw coal and middlings particles with a rotary beaker, jaw crusher, rolls, hammer mill and rod mill. Evidence from the literature indicates the detachment mode is often important for coal, ores and metallurgical products. Further confirmation comes from the crushing of a specially prepared &apos;ore&apos; of sized magnetite in plaster of Paris.

Jan 1, 1988

By L. W. Beckstead

In a conventional zinc refinery plant, zinc concentrates were roasted at 950°C. The calcine was ground and leached in a series of leaching vessels using sulfuric acid. The pH in the first leaching vessel was maintained at 2.5, while the pH of the solution exiting the last vessel was about 5.4. The leached residue typically contained (in percent) 0.1 Ag, 0.2 As, 0.7 Cd, 2 Cu, 15 Fe, 10 Pb, and 15 Zn, and it was classified as hazardous material according to the EP-toxicity test. In order to make the residue non-hazardous, and to recover most of the metal values from the residue, a brine leach process was developed. The process consisted of leaching the zinc leach residue in CaCI, brine solution at pH 2 for 1 hour at 90°C. Silver extraction was about 95 percent, while lead, copper, cadmium, zinc, and iron extractions were about 80, 50, 50, 30, and less than 0.5 percent, respectively. More extreme conditions of acidity could have been used in the leaching stage to increase zinc dissolution, but iron dissolution would have significantly increased which would have complicated subsequent recovery steps. The leached and washed residue passed the EP-toxicity leach test and could be disposed as non-hazardous. Silver, copper, and lead in the leach solution were recovered by zinc cementation, while zinc and cadmium were recovered by sulfide precipitation. The resulting solution can be recycled in the process after magnesium precipitation.

Jan 1, 1993

By B. J. Beaudry

The effect of various levels of purity of the rare earth fluorides and the calcium reductant used to prepare rare earth metals were determined. Metals which have low melting points such as La, Ce, Pr and Nd are not purified by distillation or sublimation. Impurities in the reactants remain as contaminants in these metals. Gd, Tb, Y and Lu which have slightly higher vapor pressures at their melting points than the first four metals are usually distilled to remove the Ta or W impurity introduced by the crucible and are purified slightly with respect to 0 and N by distillation. Rare earth metals that have high vapor pressures such as Sc, Dy, Ho and Er can be purified with respect to 0, N, C, as well as Ta or W by sublimation. The most volatile rare earth metals Sm, Eu, Tm and Yb are readily purified by sublimation and are usually prepared by a reduction-distillation process directly from the oxide. The importance of each step of the processes in determining the final purity of the individual rare earth metals is discussed.

Jan 1, 1989

By Xia Zhao, Yong Zhao, Wen Pan, Ze-jun Ma, Yan-juan Yang

Characteristics of the gas-solid reduction reaction between iron ore sinter and carbon monoxide (CO) gas at 1273 K were studied with thermogravimetric analyzer. The microstructure, mineral compositions and porosity of sample were investigated prior to reduction, in the 30% reduced sample, in the 70% reduced sample, and in the fully reduced sample. At the reduction degree of 30%, the hematite and calcium ferrite was reduced to 44.4 and 60.4% respectively. At the reduction degree of 70%, all the hematite, calcium ferrite and magnetite were reduced to metal iron, only 36% wustite was left in the core area. The reduction reaction began with the loose structures and spread to the nearby area. In the area of micropores, the reducing gas can easily diffuse to the reaction interface to proceed the reduction reaction effectively. So increasing the content of micro-pores is an effective way to improve the reducibility of the sinter.

Mar 1, 2018