Search Documents

By Wen Liangying, Zou Chong, Tan Xiuqin, Bai Chenguang, Zhang Shengfu

"Eight typical metallurgical byproducts containing iron were selected based on the effect of the chemical composition, particle size, additives on the burnout degree of pulverized coal. Effect of three typical byproducts including fine iron ore, BOF dust and BOF sludge on combustion reactivity and combustion efficiency were investigated using TG-DSC method. The results indicated that the three additives have obvious catalytic effects on pulverized coal. By comparison, the relative active sequence of byproducts to the catalytic combustion can be described as follows: BOF dust>BOF sludge>fine iron ore. Moreover, adding BOF dust as component of additives also shows significant catalytic effects on combustion efficiency during rapid heating process.IntroductionChina is the largest producer in the world with an annual output reaching over 6 billion tons. Solid wastes arising from iron and steel making increases the environment pressure in recently years. For instance, annual output of dust during the production of iron and steel making in China reach up to 5 million tons, which is close to 8%~15% of the amount of steel [1]. Another characteristic of these byproducts is they are finer particle which are just harder to deal with. Since some of solid wastes, including dusts, scales, and sludge, usually contain high iron content, sintering plants have traditionally been used to recycle byproducts in integrated steel plants in China. However these byproducts also have noticeable effects on sinter quality, sinter strength and productivity and, therefore, waste recycling is limited depending on the analysis of the waste materials [2]. Another method which is pre-treatment of byproducts in pelletizing process, increases of energy consumption and production cost. In addition, metallurgical byproducts often contain heavy metals and alkalis. For these reasons, recycling rate of the byproducts in China is very low. Therefore, how to recycle the byproducts in iron and steel making process is an important subject."

Jan 1, 2012

By James A. Voigt

The efficient separation of metal species from aqueous streams by precipitation techniques requires 'a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system-specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems: The effects of solution chemistry, precipitator design, and solvent choice are considered.

Jan 1, 1996

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"The worldwide demand for ornamental stones in building construction is motivating the use of their wastes, generated during fabrication, to produce compound stones. This work has as its objective to investigate the production of an ornamental compound marble (OCM) under vacuum and compression processing of a polyester matrix composite with addition of marble waste as load and as filler. Square OCM composite plates were subjected to compression and flexural mechanical tests. Samples were analyzed to obtain the density and water absorption. The OCM composites presented properties within the expected range of an artificial stone.IntroductionMarble is a limestone, composed mainly of calcite, more or less crystallized by metamorphism that ranges from granular to compact in texture. It has a density 2.7 g/cm3 and its porosity is approximately 0.4%. The UNI 8458 standard defined marble as: ""every crystalline rock constituted mainly by minerals with a Mohs hardness equal to 3-4"". In marble production around70 - 75% of whole extract material is lost in byproducts generation [1,2].In function of large volume of residues generated, the ornamental stones industry has attracted ever more the attention of environmentalists [3].Actually the marble can be pulverized to obtain calcium carbonate for industrial applications. It is also possible to obtain a thinner powder to produce concretes [l]. Some authors study the use of stone residues in concrete mortars and ceramic bricks, getting better properties to these materials [3,4].The marble residues can be also used in engineered stones, or ''agglomerated"" stones, production. The most common engineered stones in the market consist, like a polymer concretes, in polymer matrix composites incorporating petreous components. In the formulation of the engineered stones, the particulate or granular petreous components are the result of fragmentation or trituration processes to which natural stones were submitted to [ 5]."

Jan 1, 2014

By Batric Pesic

Calcium silicate slag (Di-Cal) and magnesium oxide condensate (MgO) are the by-products of magnesium smelting operations, As these oxides have acid neutralizing and metal precipitating properties, it was decided to examine their reactions with (a) individual heavy metals and (b) with a mixture of metals in solution, The resulting solid reaction products were further tested with respect to the stability of the contained metals, The stability of the solid precipitates were examined as a function of the method of precipitation and as function of the solution pH With respect to the method of precipitation, the performance of Di-Cal and MgO was compared to the performance of lime, an industry standard for heavy metal precipitation, Four different pH solutions (4,0, 5,0, 7,0 and 1 LO) were used to study the effect of pH on the stability of the precipitates. It was found that Di-Cal, in most cases, produced the most stable precipitates and thus, outperformed lime, Metal precipitates prepared by the addition of MgO were the most soluble for each metal studied, except for Se,

Jan 1, 2001

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By A. Galvan

High rate compressible media filter (CMF) tests produced exceptional total suspended solids (TSS) removal at hydraulic loading rates ranging from 97.8 to 122.2 m/h. The compressible media is manufactured from a robust resin fiber that can withstand low pH and temperatures up to 149 °C. The media porosity can be varied by applying compression onto the media. At 40% compression, the CMF can remove particles greater than 4 μ. Three synthetic test-samples were generated by Hazen Research Inc., (Golden, Colorado) to simulate the copper Pregnant Leach Solution (PLS), Raffinate and Electrolyte solutions used for the testwork conducted at their facility. The preliminary results showed that the CMF was very effective in removing TSS without the use of chemical conditioning from the above test-solutions with efficiencies of 98%, 97%, and 96%, respectively. Given the remarkably high hydraulic loading rates, the industrial equipment footprint would be minimized appreciably over conventional clarification and alternative filtration systems.

By Xun Hu, Jian Pan, Hongbin Yu, Deqing Zhu, Yanhong Luo

Lump ores are one kind of important burdens for blast furnace (BF), their metallurgical properties have significant influence on BF performance. In this paper, the relationships between the mineralogy of five natural lump ores and the metallurgical performance have been studied. The mineralogy study includes mineral compositions, microstructure and porosity, and the metallurgical performance covers reducibility index (RI), low-temperature reduction degradation index (RDI) and decrepitation index (DI). The results show that the complex lump containing hematite, and goethite has better overall metallurgical performance. For single lump, the RI of goetihte ores is higher, the RDI and the DI is strongly influenced by porosity. The hematite and magnetite ores have good anti-decrepitation and anti-RDI, but generally the RI is lower due to lower porosity, and the RI is related to the grain size, the smaller grain size is, the better reduction will be.

Jan 1, 2015

By Nina Bianco, Diana Drinkwater

MetSkill is a professional development program for metallurgical engineers that integrates with normal duties in their first one or two years of service. Graduates work together on a structured technical project, facilitated by specialists and supported by formal learning, and ultimately reported to their technical managers. The program enables graduates to “fill the gaps” in their undergraduate education, which is increasingly pertinent as engineering degrees become more general. Participants report that they enjoy the focus on more challenging (rewarding) aspects of their jobs and feel more confident about problem solving. Sponsor companies add that the relationships developed with external technical specialists enhances opportunities for innovation and development. MetSkill was delivered to two major resource companies in Australia in 2012. This paper provides an outline of the program and the reasons for its success, and demonstrates how the learning model could be applied to groups of graduates in other engineering disciplines.

Jan 1, 2014

Designing rigging systems for complex castings has been more of an art than a science. Foundrymen have used thumb rules based on past experience to develop working designs. Of late, attempts are being made to formalize the procedure through the use of rule based expert systems, process modeling and other tools. Designing risers is one of the challenges of the rigging system design. Once the riser location have been determined, an optimization technique coupled with a casting simulation code can be used to determine the optimum riser dimensions. The main drawback of using a finite element or a finite difference based process simulation code along with the optimization routine is that the computation time involved is too large. Such an approach, thus, is unrealistic for practical situations where different options have to be explored and conclusions drawn in a short period of time. This difficulty has been avoided in the present work. The optimization scheme has been coupled with a modulus based solution routine to optimize the riser dimensions. The modulus calculations provide a good and quick estimate of the freezing time at different points in the casting. A functional, obtained from these freezing time values, is minimized by altering the dimensions of the riser until an optimum shape is obtained. Some examples have been included to illustrate the utility of this technique.

Jan 1, 1994

By J. R. Goode

There are at least a dozen methods of selectively removing cerium from a mixture of the rare earth elements (REE) including separation techniques based on the oxidation of cerium to the quadrivalent state. Several of the oxidation processes have been operated on a commercial scale, others have been tested and in some cases are part of proposed flowsheets. In this paper, we describe and compare the various methods. We also present preliminary estimates of the costs of early Ce removal and discuss recovery and purity aspects of the options.

By S. N. Lekakh

Experimental work and thermodynamic simulations of cast iron refining were carried out using various additions of alkali and rare earth metals. The refining reactions for sulfur and oxygen removal were studied for melts treated with Mg, Ca, and Ce. The measured data and the results of the computer simulations were in agreement. Experimental kinetic data, together with the thermodynamic calculations, were used for optimization of the amount and sequence of the addition of nodulizers for ductile iron production.

Jan 1, 2009

By C. Y. Tang, Z. H. Chen, T. C. Lee

"In sheet metal forming process, the forming limit and strain distribution are governed by plastic instability and fracture following strain localization. It has been proved that the temperature gradient caused by plastic deformation as well as friction is one of the crucial factors to induce the strain localization in high-speed metal forming processes. In this paper, a numerical simulation of the sheet metal extrusion process has been conducted by using thermal-mechanical coupling finite element method. An improved mixed finite element method has been used to solve the large deformation elasto-plastic problem. In thermal phase, the transient heat transfer finite element method together with the Crank-Nicholson algorithm has been employed to determine the temperature field. Both the numerical results and the experimental observations reveal that the temperature gradient plays an important role in inducing the strain localization, which eventually leads to fracture failure in the sheet metal extrusion process.IntroductionSheet metal extrusion is such a process where the extrusion punch penetrates into one surface of the sheet metal material to let it extrude and flow towards the outlet of the die. This process can be used to produce protruding parts on a strip material. In engineering applications, the quality of the product is affected by many factors such as stress state, loading speed, material properties and lubrication condition. The research on failure mechanisms and improvement of formability in sheet metal forming processes by exploitation of differential thermal conditions has been of great interest recently [1-3]. It has been proved that the temperature gradient caused by plastic deformation, heat transfer, and friction between sheet and tools is one of crucial factors to affect 'the formability in high speed sheet metal forming processes [4]. In our previous study of sheet metal extrusion, it has been observed that plastic deformation is highly localized and some specimens are subjected to fracture failure in the form of crack propagation [5]. To understand this failure phenomenon, the effects of temperature gradients must not be ignored."

Jan 1, 2001

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By H. -P. Behrendt

Muldenhiütten Recycling und Umwelttechnik GmbH is a lead smelter with a very long tradition. The first reference to the existence of smelters on this site is given by a document of inheritance dated 1318. Originally run as a primary lead smelter, which was supplied with ores from the Freiberg mining district and from overseas, it was required to change it over to secondary raw materials due the abandonment of mining in the Freiberg area in 1968. Today, Muldenhüitten Recycling und Umwelttechnik GmbH has two production lines; lead production from secondary lead and waste incineration, which are closely connected and gain advantage from each other. Installations, improved technologies, and the highly skilled personnel have contributed to satisfy all demands for a production concerning quality and environment.

Jan 1, 2000

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By Junmo Ahn

This study investigated leaching kinetics by alternative lixiviants for copper leaching from chalcopyrite (CuFeS2), the most abundant copper resource in the world. As a refractory sulfide mineral, chalcopyrite shows low copper extraction due to passivation on chalcopyrite surface. Also, decrease of copper grade with high portion chalcopyrite requires the alternative leaching procedure to increase copper recovery. Therefore, alternative lixiviants such as sulfurous acid and methanesulfonic acid (MSA) were tested for both concentrate and low grade ore to enhance copper extraction. Also, an oxidant, hydrogen peroxide, was compared to ferric to find out the improvement of leaching kinetic. In concentrate leaching tests, 30 g/L MSA showed the highest copper extraction (47%), compared to other lixiviants at 75 °C. Periodical H2O2 addition enhanced copper extraction, and above 90% of copper extraction was observed within 96 h by periodical addition of 0.6% H2O2 at 75 °C. The activation energy of chalcopyrite leaching by MSA and H2O2 achieved 40 kJ/mol, which is chemical reaction control. The results of low grade ore leaching tests indicates that no significant difference among lixiviants (H2SO4, H2SO3 and MSA) with ferric was observed, all of which achieved around 37% within 24 h at room temperature. However, significant increase of copper extraction (>80%) was observed at both 20 g/L MSA and 10 g/L H2SO4 conditions by the addition of 10% H2O2.

By Liu Chunpeng

Under an inert atmosphere, the temperature enhancement of nickel bearing pyrrhotite irradiated by microwave was measured with a special metal-sheathed thermocouple and the non-isothermal rate equations were obtained. Under the controlled oxygen potential of the reacting gas in the microwave field, over 90% sulfur contained in the pyrrhotite is converted into elemental sulfur directly, the iron and the nickel are transformed into FeO,, NiO, NiFe,O, and FeSiO,. According to the experimental data the rate of the elemental sulfur produced is in diffusional control and the non-isothermal equation derived is

Jan 1, 1993