Search Documents

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on sub-optimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects, and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fail, requiring manual road input. This research proposes a new method for analysis using the road center determined by principal curve analysis of a haul truck’s Global Navigation Satellite System (GNSS) traces; analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated, and multiple linear regression analysis was conducted on each individual grid. The root mean square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Dec 19, 2023

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By L. Lacerda

Spray-on ground support membranes (GSM) or thin support liners hold today perhaps as much potential to impact underground (u/g) ground support operations as dry and later wet-mix shotcrete when introduced to mining in the latter part of the 20th century. This emerging technology has come a long way from the time the first single component experimental coatings were tested in the mid-1980s. Due to a number of factors, including occupational health risk and mine safety regulations, it has taken quite some time for the development of non-hazardous membrane products. However, at this junction most existing u/g mines that employ more conventional forms of ground support could benefit from evaluating GSM technology as a means of improving safety and the bottom line. The same is especially true for future mine developments. This paper describes Master Builders Inc.’s CS1251 GSM product and its implementation. It discusses the situations in which GSM may replace other forms of ground support. Furthermore, it evaluates GSM costs & safety issues and looks at present applications and the potentially bright future of this technology.

Jan 1, 2002

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By E. J. Haas, K. A. Rost

"This study sought to identify changes in continuous mining machine (CMM) operators’ risk perception and risk behaviors as a result of adding a proximity detection system (PDS) into their environment. To accomplish this research task, 9 CMM operators from 5 locations were interviewed. Interviews were thematically analyzed for constructs including patterns in risk perception and behavior before and after PDS integration and the process of adapting to the PDS. Operators discussed standing in the red zone less than they did before using the PDS; however, they also discussed other risky decisions they made while learning how to operate their CMM with the PDS technology such as “cheating” the technology and working faster to meet production goals. The process of relearning job tasks with technology and unintended behaviors as a result of that relearning process need to be taken into account when introducing new technology into the mine environment. The study results show an in-depth view of mine workers’ perspectives and how their job tasks and environment could be or are affected when learning how to use new technology that are relevant to companies and mine operators when introducing new technology into the mine environment. INTRODUCTION Established “red zones” can help prevent striking and pinning incidents by providing guidance to continuous mining machine (CMM) operators about where they should stand and not stand while operating a CMM. Although red zones influence operator placement positions, these guidelines are not foolproof safety mechanisms. Depending on the job task and circumstances of the mine environment, a CMM operator may unintentionally or intentionally stand in a red zone. For example, CMM operators may work in close proximity to their CMM for better visual attention cues and the ability to work at a higher rate of production [1-3]. To further enhance protection and prevent collisions between vehicles and mine workers, a proximity detection system (PDS) was developed for the industry. The PDS determines an individual’s position relative to a specific piece of machinery, issues visual and/or audible warnings to the mine worker to change positions, and, if necessary, disables machine motion [4]. The introduction of new technology within other sectors has been identified as a factor that influences work decisions. Specifically, previous research demonstrates that when technology debuts there can be an initial intrinsic risk perceived among users about how the technology will interact with their current environment and behaviors; however, these ambiguities, including the possible risks and benefits, are seldom studied [5]. Some research suggests that the constant presence of technology can disrupt situation awareness and decision-making capabilities by increasing worker responsibilities and worker cognitive demands [6-8]. Further, if workers’ perceived risks both with and without technology are misjudged, unsafe decisions that result in human error and injury may be more likely [9-11]. Although these statements are provided within a broad contextual framework, they support the need to study how technology is perceived among end users in their own environment. Because research about technological impact on worker behaviors has suggested both positive and negative consequences of technology, this issue is worth addressing in the mining industry. Specifically, research has not determined whether CMM operators view their placement choices in the red zone as safe or risky and what effect PDS technology has, if any, on risk perception and subsequent risk behavior."

Jan 1, 2015

By S. Hardcastle

Various controlled and ambient tests were undertaken to evaluate the performance of a variety of digital heat stress monitors, psychrometers and simpler temperature/relative humidity data loggers that measure, or determine, such parameters as: dry-bulb, natural wet-bulb, psychrometric wet-bulb and globe temperatures. In this comparison, funded by the Deep Mining Research Consortium, it has been found that all the instruments can competently measure dry-bulb temperature but the accuracy of other sensors could introduce significant uncertainty. For example the quality of relative humidity sensors and failure to correct for the barometric pressure difference in deep mines, directly impacts upon the calculation of psychrometric wet-bulb. The comparison has shown that the response of dry-bulb and globe temperature sensors can vary widely under different radiant heat conditions; however this would be negligible in most mines. Of more concern is the differing performance of the natural-wet bulb sensors especially at low relative humidity and low air velocity. Furthermore, from these tests and the currently available theory it was not possible to determine if any of the natural-wet bulb instruments measured that value correctly or validate any relationship between psychrometric and natural wet-bulb temperature at low air speeds where their difference is greatest. Consequently the uninformed use of some of the commercially available environmental heat stress monitors or derivations from other instruments could provide erroneous results affecting the work load category that can be accommodated or the rest ratio regime required.

Jan 1, 2009

Tellurium (Te) is one of the least abundant elements in the crust and tends to form minerals associated with copper, lead, zinc and iron sulfide deposits. Today, most tellurium production comes from the anode slimes and other wastes generated in metal refining. Most of the current tellurium produced in the world is used as an alloying agent in iron and steel, as catalysts, and in the chemical industry. However, future demand and production could increase because tellurium is increasingly used in solar panels and some electronic devices. Tellurium minerals are found in Au-Ag districts in New Mexico, but were not considered important exploration targets in the past. In New Mexico, tellurium is found associated with porphyry copper deposits in southwestern New Mexico and with Au-Ag veins in the Eureka, Sylvanite, Organ, Lordsburg, Steeple Rock, Wilcox, Mogollon, Chloride, Cuchillo, Hillsboro, Zuni Mountains, White Oaks, and Nogal-Bonito districts. The only tellurium production from New Mexico has been from the Lone Pine deposit (Wilcox district), where approximately 5 tons of tellurium ore was produced. Gold-tellurides are found with gold, silver, pyrite, and fluorite in fracture-filling veins in rhyolite at Lone Pine, with reported assays as much as 5,000 ppm Te. Other districts in New Mexico have potential for tellurium, but require field evaluation.

Feb 27, 2013

By R. B. Pedersen, A. Filipa, A. Marques

"Shallow-depth (<200m) high temperature submarine hydrothermal systems are not commonly observed on mid-ocean ridge settings, as most known systems are located within arc - island-arc volcanic settings, often proximal to coastal areas (meteoric waters added). In 2013, during the Centre for Geobiology’s 2013 oceanographic cruise (R/V G.O. Sars), a dredge successfully sampled massive sulfides and hydrothermally altered rocks from the top of a volcanic edifice (~144-284 m depth) located on the northern sector of the Kolbeinsey Ridge. Dredged samples include vesicular altered basalts, and matrix supported anhydrite, barite and barite-pyrite-anhydrite volcaniclastic breccias. Sulfidesulfate breccias depict complex zoning where numerous small vent orifices are distributed with large blades of marcasite that appear intergrown with barite. Native sulfur was observed in one of these small vent orifices. On a microscopic scale, numerous spherical silica-rich structures appear associated to these breccias. These rocks are evidence for the presence of a relatively high temperature (minimum 150ºC) shallow-water seafloor hydrothermal system in the Arctic mid-ocean ridge, far from mainland influence. This new discovery presents a unique opportunity to study the dynamics of fluid chemistry, metal mobility and precipitation in shallow hydrothermal systems. The remote location of this system dictates that fluid recharge will be influenced solely by seawater and magmatic fluids, In July-August 2014 we expect to survey this new field and acquire new and comprehensive data."

Sep 1, 2014

By F. -J. Wodopia

Sustainability of energy supplies has been an issue of general interest for a long time. Whilst in the past the continuous productive use of natural commodities was in the fore, its compatibility with the environment and climate and ultimately also social aspects have recently gained more and more attention. Today many discussions focus on the climate compatibility of individual options to act. Fossil fuels, in particular coal and lignite, are generally challenged because coal use makes a significant contribution to global man-made CO2 emissions. The drastic increase in the consumption of fossil fuels is not explained by the fact that coal utilisation technologies are not or cannot be sustainable but rather by the growing world population and the endeavours numerous national economies trying to catch up economically. Coal is the world’s No. 1 fuel and, in the view of many experts, will keep this position also in the foreseeable future. The access to its deposits plays a significant role for the economies of the emerging countries. Consequently the aspects of energy security and economic efficiency need to be considered at eye level with climate compatibility. In Germany, however, the public acceptance of fossil fuels and of large industrial projects is in the focus of attention.

Jan 1, 2011

By Charles F. Herbert

It is difficult to decide who most deserves credit for discovery of a mining district that has produced over 19.8 Mg (7,000,000 fine oz) of gold and still contains a large reserve of low grade ore. Fred Culver may have made the first discovery. In the summer of 1867, the ship&apos;s log of the Hudson&apos;s Bay Co.&apos;s steamer Otter stated that Fred Culver had been found nearly lifeless from wounds, without provisions, but with some 2.3 kg (80 oz) of rough, placer gold in the bottom of his canoe; he told of finding a rich creek and an attack by Indians that caused the death of his two companions. The place of rescue was about 24 km (15 miles) southeast from the present site of Juneau. Possibly John Muir, the hero of modem environmentalists, should be given important credit. In 1879 he reported finding mineralization along what later became to be known as the Juneau Gold Belt, and it was his report that induced the cantankerous German mining engineer, George Pilz, to grub- stake some of the prospectors who had drifted into Sitka from the declining gold placers of Cassiar, British Columbia. Pilz also offered rewards to Indians who might report gold discoveries.

Jan 1, 1990

By A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures to the equipment operators. As part of this effort, the National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study which determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system which was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, being a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels comparing outside to inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system?s efficiency. Testing using particle count instruments performed during non-production time periods on both pieces of equipment indicated Protection Factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By Jai Ghosh, Aprad E. Torma, Roger Guay

The catalytic effect of ferrous ion in the industrial biohydrometallurgical heap and dump leaching processes is explained. During the bacterial leaching of metal sulfides, ferric ion will partly be hydrolyzed and a variety of sols, gels, amorphous and/ or crystalline mono- and polynuc- lear hydroxo- and sulfato complex species formed, especially by olation and aggregation reactions. There are many problems associated with these iron precipitates especially in the purification of leach solutions. The present study will discuss the iron precipitation reactions; gives kinetic and thermodynamic evaluations of the effect of temperature on pyrite and ferrous iron oxidation; and reports on the tolerance of heavy metal ion concentrations by Thiobacillus ferrooxidans.

Jan 1, 1989

Coal bursts are one of the least understood yet the most critical hazards in underground coal mines. The ground motions induced by seismic events can trigger unstable failure of coal and rock mass and degrade the surroundings of an excavation. Therefore, the characteristics of ground motions should be fully investigated for an improved burst risk management. This paper analyzes ground motion features of a longwall panel from a typical underground burst-prone coal mine in China. The results showed that most of the ground motions on roadways were hardly initiate coal bursts due to insignificant energy input to the damage. The intensity of ground motions in near-field zone were nearly 20 times higher than those in far-field zone. The strongest vibration on roadway was induced by a coal burst with energy of 28,600 kJ, which can cause ground motion of 0.77 m/s and equivalent dynamic stress of 14.69 MPa. The findings of this paper can improve the assessment of seismic risks and its management.

Jan 7, 2020

While SME is hosting its Annual Meeting at the Phoenix Convention Center, Feb. 28 to March 3, one of the finest collections of mining history will be on display just 15 blocks away at the Arizona Mining and Mineral Museum. Inside the museum, visitors will be treated to a treasure trove of minerals, gems, me¬teorites, rocks, fossils, mining artifacts, historical exhibits and interactive displays on modern mining. The museum is located at 1502 West Washington. For SME Annual Meeting attendees, this is a free, eight-minute Dash bus ride 15 blocks west of the Phoenix Convention Center.

Jan 1, 2010

By Robin J. Batterham, Dave J. Robinson

The history of mineral processing in general and flotation in particular is long and has always been tied to mining methods of the day. Building on the ever-improving fundamental understanding of the underlying science, the most significant trend in flotation has been the putting into practice the learnings from trailblazers such as Professor Fuerstenau that has given the confidence that enabled an ever-increasing scale of operations. There is, however, doubt this ongoing trend is enough to maintain the economics against global trends such as that of falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. In addition, we see that globally, the social license to operate for mining (and hence mineral processing) is far from secure and, at the very least, is under much more rigorous scrutiny. In this paper, we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10–20 years but in the meantime, the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation, as we know it, will change significantly.