Search Documents

By Alexander N. Winchell

The cities of St. Paul and Minneapolis are located side by side on a double loop in the Mississippi River near the eastern boundary of Minnesota. Both cities lie on both sides 'of the Mississippi River, which in this region describes an S-shaped curve. The two cities together have a population of over 600,000 people, gathered in an area which has grown to be a single urban district inasmuch as the two cities have expanded until they occupy all the territory formerly between them, though the business centers are ten miles apart. St. Paul is located at the head of navigation on the Mississippi River and Minneapolis, farther upstream, at the Falls of St. Anthony. A recent water¬power development below the Falls of St. Anthony, constructed by the Federal Government, has at the same time made possible navigation to the foot of St. Anthony Falls through a lock around the dam which replaces the former rapids. Minneapolis, in 1920, had a population of 380,000 people, and St. Paul, 235,000. The two cities occupy land at an elevation of 700 to 900 feet above sea level. The average elevation is slightly less at St. Paul. Minneapolis has nearly 4,000 acres of parks and park¬ways, while St. Paul has nearly 2,000.

Jan 1, 1920

By Kef ton H. Teague

This paper will discuss bentonite deposits in Texas, Oklahoma, Louisiana, Mississippi and Alabama. The discussion will be re¬stricted to a review of the so-called calcium or non-swelling bentonites. In other words the exchangeable cation is calcium. The term "bentonite" is used to describe a clay material, composed essentially of the clay mineral montmorillonite. In addition, bentonites may contain various impurities such as glass shards, feldspar, quartz, muscovite and biotite mica, glauconite, pyrite, hydrated iron oxide, gypsum, organic material, etc, Most of the southern calcium bentonites contain at least 70% montmorillonite, Bentonite as mined may range in color from dark grayish greens through various shades of grays, reds, yellows and browns to nearly white. It is normally massive and breaks with a conchoidal fracture. When air dried, closely spaced shrinkage fractures occur. Moist bentonite has a soapy feel, with little or no obvious "grit". Bentonite deposits were first discovered in Mississippi about 1925, in southern Monroe County. During the thirties and early 1940's, deposits were identified in Alabama, Texas, Oklahoma, and Louisiana. Perhaps the earliest production of southern bentonite was from a deposit in the valley of the Tombigdee River, south of Jackson, Alabama in 1936. Production commenced in Mississippi during the latter part of 1938 at Pontotoc. The growth and development of the bentonite industry in the southern United States owes its beginning to three events. The first of these was the discovery by German researchers,

Jan 1, 1972

By Juan C. Diaz, Juan P. Carmona, Manuel Z. Salgado, Oscar J. Restrepo

The “Teaching Kids” project is an educational initiative for young people and children from elementary schools. It is carried out by Mining, Geological, and Environmental Engineering students from the SME Student Chapter of the Universidad Nacional de Colombia, Medellin. The primary purpose of the Teaching Kids project is to share knowledge about geosciences and mineral resources in a didactic and attractive way, emphasizing the importance of identifying the use of minerals in daily life and responsible and sustainable mining in our society. Furthermore, this project aims to promote the importance of pursuing geoscience majors in the new generations and improve the mining industry’s public perception. Different methodologies related to early childhood education are implemented, such as gamification, in which the dynamics of games are adapted during the development of workshops to teach and learn in an active and motivated environment. Furthermore, the Montessori Method is used. It implements textbooks, sensory mineral boxes, and presentations to allow learning through experimentation itself (Montessori 2003). The implementation of this methodology has been successful; it has shown high engagement, participation, and retention of the basic concept of geoscience and mining.

Feb 1, 2025

By Mustafa Kumral, Mehmet Balci

Strategic mine planning focuses on cutoff grade selection, capacity planning and block sequencing. Despite significant knowledge accumulated, potential value can be added to mineral sourcing by addressing various aspects. A case study on a metallic deposit with a lognormal grade distribution examines if grade/metal distribution influences cutoff grade selection. Six data sets with different shape and scale factors, but the same ore tonnage and metal quantity, are analyzed. Results indicate deposits with lower shape and scale factors are more sensitive to metal price and discount rate changes. The study also investigates the effect of economies of scale (EoS) on project value, focusing on the ratio of variable cost to total cost (capacity factor). Two regression analyses are conducted for optimal capacity planning and cutoff grade selection. The first shows capacity planning is highly sensitive to the EoS of mining and mineral-processing costs, with grade variability and metal distribution being negligible. In the second analysis, grade variability and EoS of mineral processing costs are vital for cutoff grade selection.

Sep 1, 2024

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By R. D. Grove

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators' vision when major deviations occur. An image analysis system has been developed by IMC Fertilizer to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By B. A. Massey

Sooner or later, we'll encounter a subordinate, peer, or boss that will test our management skills to the limit. The chances are good that our formal educations have not fully prepared us to effectively handle the situation, and through trial-by-fire, we have learned that the management of people is often as much an art as it is a science. Assertiveness - as opposed to agressiveness - is basically positive persuation. Assertive management techniques can help combine the art and science of managment to sell ideas, accomplish goals, direct the workforce, and generally promote the corporate - as well as our own - objectives

Jan 1, 1986

By Erich Sarapuu

Today's increasing needs for rapid excavation have stimulated efforts to break rocks without explosives. The application of electric energy for this purpose has been studied by a number of investigators. Following principles have been used in electrical rock breaking: 1. induction heating5 2. high frequency heating4, 14 3. microwave heating6 4. contact resistance heating9,12 5. resistance heating11,13 6. electron beam heating1, 3 7. plasma jet heating2, 8 8. arc heating7 9. condensor discharge energy14 In this paper the presentation of the principles of electrical fragmentation is limited to a process called "electrofracing". This technique uses electrical heating of rock by electrode contact resistance9 and resistance heating" phenomena. The electrically induced stresses inside of rock generate forces which break up the material. The fracturing of ore takes place by tensile stresses instead of compressive forces. The electric energy merely creates fractures in the rock and the separation of fractured material takes place by subsequent mechanical handling. Energy requirements in secondary breaking of iron ores have been about one to two kilowatt-hours per ton of ore. Power requirement is a function of the degree of fragmentation.

Jan 1, 1969

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

The paper discusses the evolution of the geometallurgical model at the Escondida mine in northern Chile, the world’s largest copper producer. It highlights the transition from early metallurgical forecasting methods to a comprehensive model that includes spatial distribution of metallurgical forecasts. This model helps in planning and adapting to the variability in ore characteristics, such as hardness and mineralogy, which affect processing performance.

Dec 1, 2023

By R. Fields

Nevada is primarily known today for its nation-leading production of gold and silver. However, industrial mineral production continues to play an important role in providing construction materials to help make the state the fastest growing in the United States. Aggregate production in Nevada was about 20 million tons in 1991. Most of that was used in construction in the fast-growing Las Vegas area. The state leads the nation in the production of barite and mined magnesite and has significant production of lithium carbonate, diatomite and gypsum. Other industrial minerals produced in the state include specialty clays, silica, lime and dolomite and relatively small production in salt, perlite and dimension stone. Industrial minerals operations are subject to state and federal permitting requirements, especially in the areas of air and water quality and mined land reclamation. As in all segments of the mineral producing industries throughout the nation, the amount and complexity of regulations affecting industrial minerals has increased significantly in recent years. Nevada is no exception.

Jan 1, 1993

By J. Gonzales

For this paper, blending is conceived as a linear process that takes a proportion from one stockpile or location and mixes it with another proportion from another stockpile or location, with the aim of obtaining a set of attributes in the final combination that satisfies a given quality standard. A blending class is the combination of ore attributes and grade limits that should be stockpiled in order to achieve the target quality for the process Plant. Current literature considers the number of blending classes in the Open Pit Scheduling Problem as fixed; however, this paper shows how to define specific blending classes for a given deposit so that the schedule can be solved with Sequential Linear Programming. Finally, a practical application in a Peruvian copper mine is shown, involving four ore attributes: alteration code, arsenic, oxide content and copper grade. INTRODUCTION In copper ore deposits, blending for quality has not been a typical issue as it was for coal and iron ore; however, current copper deposits in the world are becoming geologically and chemically more complex than in the past and is not uncommon to have quality standards involving up to four attributes, introducing an additional complexity to the mine scheduling process [1]. In order to solve the Open Pit Scheduling Problem with multiple ore quality constraints, two assumptions are necessary [2]: - Grade constraints are defined only by specifying an upper and lower limit; - Ore attributes in stockpiles are pre-determined, i.e., the upper and/or lower grade limits defining each stockpile are already known at the time of setting the schedule. Assuming each ore attribute is classified as high, medium or low, and there are four attributes to be controlled in the target ore quality, the number of possible blending classes would be 3^4 = 81. This number is impractical to manage in Operations, and increases the complexity at the time of running the schedule; therefore, a more efficient way of classifying ore is required. Note that in practice, one blending class can be split into more than one stockpile location due to physical capacity constraints. Therefore, the number of stockpiles could even be more than 81. BLENDING CLASSES DETERMINATION For a given set of ore grades with lower and upper limits to be achieved, one has to find all feasible ore classes such that when blended, their grades will lie within those limits.

Jan 1, 2019

By H. M. Woodrooffe

In the U.S.S.R. three of the world's major-known phosphate deposits are located. These have an estimated reserve of 2,600 million short tons of contained phosphorus. The best known lies in the "Khibiny Massif', an alkalaic rock formation some 600 square miles in area with mountain peaks rising to an altitude of 3300 ft above the surrounding terrain. Location and Climate The Khibiny Massif lies north of the Arctic Circle in the Kola Penin-sula, 100 miles south southeast of Murmansk, at a latitude of 67° 30' north and a longitude of 35° 30' east. It is serviced by rail from Murmansk and Leningrad (900 rail miles south). Figure 1. The phosphate operations are centered about the two cities of Apatity and Kirovsk. The former has a population of 35,000 and is on the Leningrad¬Murmansk railway. Kirovsk, 15 miles to the east, is now a city of 85,000. The region is at the limit of the tree line with most of the ground cover typical tundra. The mean annual temperature is -4°C and, in a normal year, precipitation occurs on 240 days. Because the temperature does not exceed freezing for 300 days each year, virtually all of the precipitation is snow. The two towns are nestled between mountains and, because of the weather, extensive avalanche control systems incorporating major engineering construction have been introduced to divert snow slides away from the populated areas. General Kirovsk was first settled in 1923 and the apatite occurrences were recognized shortly after. In 1933, the first concentrator for the recovery of the mineral was completed, producing in its first year of operation 170,000 tons of concentrate. With the growth and demand for phosphate in the U.S.S.R., a second concentrator was erected at Apatity. It calve on stream in 1963. Because of the severe climate, in the early days mining was limited to 85 days per year. With the introduction of new techniques and improved mining methods, the season has been extended to 115 days.

Jan 1, 1972

By Dan Norrgran

In recent years, a great deal of attention has been focused on developing mill liners to increase wear resistance, improve grinding efficiency and reduce energy consumption in milling applications. The installation of an appropriate mill liner is critical as it affects the overall cost and product quality. A mill liner has two specific functions. The first is to protect the mill shell and mill ends from direct contact with the abrasive grinding media (in this case, the liner serves as a wear surface). The second function is to transport the grinding media, creating energy for size reduction. The liner acts as a lifter, mechanically transporting and cascading the grinding media. The mill lining is a major cost in the milling operation. The costs associated with the mill lining include the capital cost of the lining, downtime required to replace the worn liner and the labor for installation. Generally, in hard rock mining, the life of a mill liner in secondary ball mills is 12 to 24 months.

Jan 1, 2009

By Alan C. Richter

Introduction The East-West Gateway Coordinating Council is an organization of local governments formed in 1965 to identify regional problems and to formulate policies, plans and programs to resolve them. The major goal of the Gateway Council is to improve the quality of life for the citizens of the St. Louis Region. While East-West Gateway Coordinating Council is the organization I represent and it only deals with the St. Louis Metropolitan Area, you will find one or more similar organizations in each of our nation's urbanized areas. As a result, for illustrative purposes, I will use my organization to portray what is happening nationwide. For example, in order to eliminate duplication, the Council reviews local applications for approximately 100 federally funded programs in such areas as highways, mass transit, parks, water treatment, and sewers before they can be sent to the appropriate funding agency. The Council's varied functions place it in a unique position of receiving more and more responsibility for developing strategies of implementation of various environmental regulations. This is due to the fact that environmental control is a relatively new field and we, as a country, are relatively inexperienced. The resulting regulations and guidelines will depend, to a great extent, on what the general public is willing to accept in terms of controls and what price they are willing to pay in terms of taxes and increased costs. Land Use: Growth vs No Growth This is perhaps the most encompassing environmental issue. We, as a nation, are beginning to realize that land is a limited natural resource and that the way we choose to use 'this resource affects many other aspects of our lives--whether we can catch edible fish in the Mississippi, how much we pay for sewer services, if we can swim in a

Jan 1, 1977

Iran possesses very large copper resources, estimated to contain around 4-5% of the world's known copper inventory. There are several small private sector copper mining operating in the country, but Iran's copper industry is dominated by the state-owned National Iranian Copper Industries Company, which operates the world-class Sar-Cheshmeh open-pit Mine. This mine was developed in 1970s before the 1979 Islamic Revelation by the Atlantic Richfield Company (ARCO), the former Anaconda Copper Mining Company. Current Iran?s copper cathode production is about 250,000 mtpa and recently it is targeted to reach to 700.000 t by 2014. The required finance for this target is estimated US $2.25 -b, i.e. US $5000 for each tonne capacity. The copper content of the mineable reserves of the country is estimated about 19 Mt. It is not unlikely this amount increases in close future. Currently, almost 30 projects consist of mine, concentrator, smelter, refinery, acid plant, leaching, bio-leaching are underway. These projects are a golden opportunity for the local and foreign companies, but the recent sanctions are very challenging that all studied in this paper.

Jan 1, 2012

By T. Szwilski

The Appalachian coal region is an area here the small mining operation dominates. The large number of small operations makes the coal industry in chat area very competitive, the industry concentration ratio being low. This feature is reflected in the nature and behavior of the coal supply and demand viz a viz the coal market. The vast majority of the small coal operations in Eastern Kentucky for example, are contractors. The circumstances under which a large mining company can elect to use contractors to supplement their coal production are examined. The pros and cons of small underground single unit mines and larger multiple unit mines are discussed.

Jan 1, 1986

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011

By E. B. Graves

I have been asked to talk to you this morning about phosphate marketing and distribution. In discussing this I will attempt to answer such questions as: What is phosphate? Where do we get it? What form is it and how do we sell it? How do we distribute it? How is it applied? And last, but not least, What about the future? To start with, phosphate is one of the three primary plant nutrients. It is the element essential for root structure of plants. Plants, like humans, need a balanced diet. Thus, the amount of phosphate required by individual plants is, in part, related to how much of the other nutrients are used. Virtually all soils contain a certain amount of available phosphates. Back at the turn of the century the most common source of additional plant nutrient, including phosphates, was from cattle manure. The use of chemical fertilizers is something that has grown significantly during the last half century, and in particular, the last 20 years.

Jan 1, 1977

By H. M. Ray

The discovery of the New Lead Belt in the mid-'50s began a search for mill design criteria that is continuously updated. The opportunity to design, construct, and operate four new mills in the span of 20 years provided fertile areas for new concepts. The central theme for design parameters encompassed simplicity, functional, and economic consideration. Ore characteristics for each plant remained relatively constant, providing stable criteria for grinding circuits. Bond index nominally 10-12. Flotation circuit parameters were based upon power application with 10-20% excess capacity built-in to protect recovery. Newer equipment exhibits greater power application efficiency lowering horsepower requirements per ton. Instrumentation was installed to stabilize circuits, protect equipment, and improve products. With ever increasing requirements of higher quality products, environmental considerations, and operating cost pressures, the upgrading of operating procedures is in a constant state of flux. Installation of more efficient equipment, chemical processing, or any other technique would be considered as feasible. Current practice is for St. Joe to design and engineer in-house its own plant design. The exception being detailing of structural steel. It is felt that familiarity with past design criteria serves as a valuable foundation to incorporate changes. Also, direct contact with operator provides specific data, and feedback for constructive criticism that is utilized for defining and correcting problems. The results are in reality an operator's plant with the benefit of advancing technology that meets the demands for improved products without sacrificing the economies of throughput or recovery.

Jan 1, 1977

By E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality over time. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999