Search Documents

By D. F. McCarthy

INTRODUCTION Mined underground chambers specifically designed for the purpose of storing liquefied petroleum gas (LPG) at ambient temperatures have been in use for over thirty years. The first caverns were developed by Warren Petroleum of Tulsa, Oklahoma, in 1948, for its plants in Texas. The basic concept of an LPG-storage cavern is to create a space in an impervious formation at a depth sufficiently below the water table so that if any movement of fluid occurs the ground water will enter rather than the gas escape from the cavern. In the past, the primary reason for LPG storage underground has been its attractive cost advantages over steel storage on the surface. At current prices the cost of storing 7.949 ML (50,000 barrels) would be equivalent, whether stored on the surface or underground; whereas 79.494 ML (500,000 barrels) of storage underground costs only one-fifth of surface storage. It is usually uneconomical to excavate less than 79.494 cu m (50,000 barrels) of storage space. The fixed costs - engineering, mainshaft and ventilation shaft - are a substantial part of the total cost, whereas the incremental costs for excavating additional storage are relatively low. Recent concern over the hazards posed by the handling and storage of LPG and liquefied natural gas (LNG) has led to a new interest in the underground storage of these gases. Underground storage offers the following advantages: safety, security, low initial cost, low maintenance cost, operating, cost, minimum land require-

Jan 1, 1981

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992

By J. W. Craven, M. Katom, K. M. McCaffery

At Ok Tedi, ore type and SAG feed size distribution vary widely and frequently. This makes control of the SAG mills by application of the power/pressure relationship difficult. Power logic has traditionally been conservative due to power spikes associated with rapid size-distribution changes. A new expert system was installed in early 2000. The system incorporates multiple state fuzzy logic to deal with frequent and radical ore type and size variations, along with monitoring of motor temperatures. A short-term power spike no longer warrants immediate radical action. This has resulted in increased mill throughput and improved circuit stability. Key words: SAG mills, Mill control, Fuzzy logic

Jan 1, 2003

By Chester R. McKee, Amar C. Bumb, Kohei Kawakita

Unlike many other heavy metals, gold can be profitably mined in small operations because of the prices. One mining technique that seems ideally suited for small deposits of gold and for certain large, lowgrade oxidized disseminated deposits is solution mining. Solution mining generally requires lower capital investment and operating costs than conventional mining and milling and is safer and less degrading to the environment. Although gold has long been recovered by cyanide leaching following conventional milling, solution mining as discussed here gained momentum only in the past two decades, during which time alternative lixiviants instead of cyanide have been researched. Chamberlain and Pojar (1981) classified solution mining systems used today as three types, namely heap, dump, and in-situ leaching.

Jan 1, 1990

By R. Hogg, R. C. Klimpel, D. T. Ray

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition, etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size and density.

Jan 1, 1988

By Steve Crewdson

High tonnage hoisting of materials by vertical conveyors through deep shafts is a relatively new concept in mining that is proving to be effective. The development of the Pocketlift® belt by Metso Flexowell, located in Moers, Germany, enabled the installation of a deep shaft vertical conveyor in 2002. This application followed years of design and operational experience gained in medium-depth shafts around the world. The design, manufacture, installation and operational experience of an 1,818 tonnes capacity, 273 meters vertical lift, Pocketlift® belt system at the White County Coal Pattiki 2 Mine is the subject of this work

Jan 1, 2004

By Rodger E. Denison

The Middle Ordovician Simpson Group in the Arbuckle Mountains of southern Oklahoma contains sandstones of unusual purity. These have been exploited as glass sands since 1913 (Ham, 1945). Where quarried, the sandstones are uncemented or weakly cemented, greatly facilitating mining and processing. The origin: sedimentary setting, and lack of cementation of these valuable sands has been the source of much discussion. The lowest of the sandstone units in the Simpson is at the base of the Oil Creek Formation. The basal Oil Creek sandstone is exposed in a series of accessible quarries north of the town of Mill Creek in Johnston County. Virtually all conclusions and generalizations concerning origin of the Simpson sandstones are based upon observations made in these quarries. The three Simpson sandstones overlying the Oil Creek share many of the same distinctive qualities, and there is an assumption that they share a common origin.

Jan 1, 1999

By Derek M. Hutchinson, Don Zeni

The construction of shafts by blind drilling has been made cost effective by advances in technology and experience. The techniques of blind shaft drilling are discussed and a brief history presented. A recent use of blind shaft drilling to access a small gold ore body in Australia is described. Finally, the most recent developments in drilling machinery are reviewed together with possible applications in new and existing mines.

Jan 1, 1987

By S. Eugene Sankey, Geoffrey L. Payne

Modern metallurgical processing often depends heavily on the use of flocculants to achieve the high levels of efficiency required. Selection of the optimum polymer can be complicated by the effects of process streams on the chemical and physical stability of the chosen polymer. Similarly, the presence of the polymer can have positive or negative side effects on process streams, such as phase disengagement in solvent extraction, foaming at filters and thickeners, crystal growth modification or flotation performance. Guidelines are given to highlight areas where problems may occur and suggestions made as to how these can be overcome. Practical advice on the preparation and application of polymers in process liquors is provided.

Jan 1, 1986

By Samir Kumar Das

Presently Geographic Information System (GIs) is gaining wider acceptance id appreciation in various resource management surveys, generation of various thematic maps, various scientific investigations, environment assessment, disaster management, etc in India but they are general in nature. A huge number of Global Positioning System (GPS) based "Total Station" are playing good roles in India for accurate and quick surveying . The GPS based real time Mine Management and Truck Dispatching System for optimization of productivity is being installed in the Panchpatmali opencast bauxite mines of India. This paper dealt in depth on GIs and GPS and their present roles in the Indian mining scenario.

Jan 1, 2002

By V. J. Kecojevic, W. A. Wilkinson

Mining companies are increasingly looking at Global Positioning System (GPS) technology coupled with 3D mine planning and visualization systems to deliver increased productivity and reduction in operating costs in drilling and blasting operations. Leveraging GPS into drill and blast operations requires that a drilling plan be developed and imported into the GPS to guide the operation to a planned and desirable outcome. State-of-the-art mine planning software systems provide the engineer with a 3D environment in which to design and visualize drill and blast plans. This paper discusses producing and exporting 3D drill and blast plans to GPS and how some coal companies are utilizing GPS and mine planning software technology in the drill and blast process.

Jan 1, 2004

By E. R. Braer, C. J. Bise

The trend in underground room-and-pillar coal mining is to employ remote-controlled, continuous-mining machines and extended cuts to depths of 12 m (40 ft) or more. This system of coal extraction, adopted by more than 435 mines, can create additional worker safety hazards. To address the ground-control-related safety hazards, a combination of statistical analysis and numerical modeling was used. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the coal mine roof rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling was completed to predict roof displacements during extended-cut mining. This paper describes the results of these studies and their impacts on the safety of extended-cut mining.

Jan 1, 2000

By Alex Harrison, Steve Kasper

Various countries around the world have testing and manufacturing standards in place for steel cord belting. These standards are very comprehensive in what they allow the end user to specify, however, their practical significance in terms of belt life is more difficult to quantify. Such testing standards will be briefly reviewed in this paper in relation to the implication for end user expectancy. Since there is no US standard of manufacture, the end user is left with writing their own specifications. In addition, such standards do not address the effect on belt life of manufacturing faults, such as cord plane buckles, or lateral cord movement. Some new technology used to test steel cord belting will be described as an aid to both manufacturer and end user. Specific end user related issues addressed on this paper are: Tracking and belt quality Cord plane irregularities and performance Cord size and belt life Cord fatigue and testing

Jan 1, 1993

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application, for geological structures, has been criticized, for its reliance on subjective interpretations. The Mine Safety & Health Administration's Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and. fault zones that were parallel with projected lineaments. The Roof Control Division's successful identification o f lineaments associated with roof falls and high wall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions would allow mine operators to obviate safety concerns that might otherwise adversely affect the health and safety of miners.

Jan 1, 2003

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By N. S. P. Kumar

INTRODUCTION Development work at Carr Fork Mine of Anaconda Copper Company in Tooele, Utah commenced in August 1974. A decision to install an underground gyratory crusher for primary crushing run-of-mine ore and waste was made in 1976. Higher throughput rates, larger reduction ratios and greater flexibility in terms of meeting immediate and expanded production needs were the main reasons for selecting the gyratory crusher over the jaw crusher. UNDERGROUND MATERIALS HANDLING Underground crushing and conveying system was designed for a capacity of 16,300 mtpd of ore and waste on a 2-shift, 5-day week basis. Engineering and design of crusher complex was performed by Anaconda engineers at Carr Fork. Figure 1 represents the longitudinal section of mine showing the general materials handling system. Mine area is trackless except for materials and production haulage which is run on rail track on both 1200 and 970 levels. Ore from stopes and waste rock from development headings are handled by 3.8 cu m (5 cu yd) Jarco scoops and dumped into 2.4 m (8 ft) diameter ore and waste passes at the 1200 level. The material gravitates down to the 970 level where it is loaded into 12 cu m (420 cu ft) ASEA mine cars using side loading chutes. The muck train, consisting of 15 to 18 cars and two 27 mt General Electric trolley locomotives, is hauled over a distance of 2,300 m (7,550 ft) to

Jan 1, 1981

By John A. Herbst, William T. Pate, Ruben Tello Flores, Humberto Arreola Zarate

Plantwide control is the networking and coordination of individual control systems throughout the plant to enhance plant performance. The high level decision making involved in this coordination is used to achieve overall plant optimization. Decisions must be based on knowledge and information moving between control systems in both downstream and upstream directions and on management information systems containing financial data on the impact of coordinating actions. For example, certain quantitative descriptors of upstream operations are passed to the downstream control systems to prepare those operations for the feed material they will receive. Likewise, other quantitative descriptors of downstream operations are passed to upstream control systems to modify their output. In this case, setpoints are determined throughout the plant which maximize profitability, given current ore conditions and plant operating constraints. Due to the wide area coverage of this coordinator, it is forced to draw on several diverse information and knowledge bases. Such a coordinator, then, must rely on a combination of heuristic logic, model-based control and neural networks to unify the knowledge bases as well as to take advantage of their strengths and to compensate for deficiencies. A description is given of control systems for primary and secondary grinding and flotation at a large copper concentrator and how they are being integrated to achieve plantwide control. Financial implications are discussed.

Jan 1, 1995

By Jeffery H. Stricklin

Jim Walter Resources operates five underground coal mines with longwall faces in operation in four of the mines. Due to high air velocities (1000-1200 fpm) needed for methane control together with the friability of the coal, dust control on JWR longwalls offers unique challenges. We have tested many innovative measures to reduce respirable dust concentrations on longwalls with varying degrees of success. These measures include the "shearer clearer" system, different drum water spray configurations, sprays on the longwall belt, stageloader and crusher sprays, wetting agents in the spray water system, and homotropal ventilation. Water infusion of deactivated horizontal methane drainage holes in longwall panels is now being evaluated. A study was completed in November 1986 where water was infused into two horizontal de-gas holes. Personal gravimetric samplers were used to measure respirable dust concentrations and showed a significant reduction in the infused zone. A more in depth study will be conducted. This paper will describe the dust control measures presently used on JWR longwalls, give the results of past studies, and discuss new methods proposed to control longwall dust.

Jan 1, 1987

By D. Robert Weir, Roman M. G. S. Berezowsky

Pressure oxidation can virtually always render refractory auriferous sulphidic ores and concentrates amenable to cyanidation. Its effectiveness as a pretreatment of refractory gold feedstocks is reflected by the successful startup and operation, over the past four years, of four commercial plants. At least three more are scheduled to come on stream during the next three years. Over the past eight years, a variety of ores and concentrates have been subjected to integrated miniplant testing and process demonstration by Sherritt, and data derived from these studies have been used in the design and construction of several of the commercial facilities. Some factors affecting the selection of pressure oxidation in gold recovery processing are discussed.

Jan 1, 1989

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987