Search Documents

By Stanislaw Wasilewski, Zdzislaw Krzystanek

Ventilation process in deep mines features relatively low efficiency. Commonly used passive control by means of regulators and flow throttling leads to remarkable energy losses that could be lower if effective monitoring and remote control of main fan operating point were implemented. In the paper, some results of investigation carried out in Polish coal mines to evaluate real energy losses in ventilation process are described. Different methods for main fans performance monitoring and control are considered and compared especially those using fan drive speed control to minimize power consumption. On the other hand some criteria for power evaluation are analysed and algorithms for optimum location of controllers in ventilation network are considered. The results of investigation are being implemented in the first system for monitoring and control of main fan operating point in Miechowice colliery.

Jan 1, 1995

By J. G. Groppo, J. G. Justice, B. K. Parekh

Removal of particulates and/or metal ions from mineral/coal processing waste water is a necessity from the environmental point of view. This paper describes application of a novel AC- electrocoagulation technique to remove the particulates as well as metal ions using AC power. A series of laboratory tests conducted on a stable black water sample obtained from a sub-bitminous coal operation provided a clear supernatant (-10 NTU) from the suspension. The process also shows promise in removal of up to 90 percent of phosphate ions and other metal ions (copper and nickel) from solution. A preliminary economic evaluation of the process will also be included.

Jan 1, 1992

By George A. Hoffman, Richard J. Proctor

INTRODUCTION We will discuss here only the subway construction phase; that is, two to five years at a given location--not the long-term analysis. We also will compare some tunnel construction methods used for BART and in Los Angeles. Typically, urban planners and engineers try to balance a new mass transit system to include tunneled subways, cut-and-cover construction in city streets, and elevated guideways. Their decisions are based on many factors, most of which can be quantified. But there are some socio-economic-environmental factors which are almost intangible, or nonquantifiable, and these are rarely included in the final report for a rapid transit system. There are two reasons for this: First, it is difficult to evaluate disruptions and psychological inconveniences to individuals and to the community during the construction period, and even more difficult to assign costs because the valuations are always subjective. Second, the rapid transit project capital costs are given in the final report and the public knows them; but the intangible social costs are borne by the affected neighborhood community, not the entire city, and as such they are "hidden costs," which in fact may add as much as 25 percent to the total system cost.

Jan 1, 1974

By Jiqing Zhang, Jon C. Yingling, Andrzej M. Wala, Richard Ray

The purpose of this paper is to present how Computational Fluid Dynamics (CFD) simulations can be used to study the flow across the main airways of a mine ventilation system. in particular, the flow through the transition zone between the upcast shaft and main fan ductwork was investigated. These studies consider potential design modifications of this transition zone to reduce the energy cost. Although CFD has many advantages, it does not completely eliminate the need for experiments, which are still needed to validate numerical solutions. For this reason, data collected during actual mine tests and CFD simulations are compared in this pa- per. This comparison allows a better understanding of the flow phenomena. Moreover, once the numerical solutions have been validated, CFD can be used with better confidence to predict the effect of changes in ductwork configurations on energy losses. CFD reduces the number and cost of tedious experiments, while enabling a broader scope of design comparisons.

Jan 1, 1997

By Don Rose

I. INTRODUCTION The Atlanta Research Chamber is an UMTA-sponsored applied research facility studying tunnel design, excavation and support systems. It is located directly below Peachtree Street in downtown Atlanta, Georgia. It is included in the CN-120 contract to build the Peachtree Center subway station, a part of the Metropolitan Atlanta Rapid Transit Authority (MARTA) multi-billion dollar "Phase A" 53-mile transit project, which is 80 percent funded by UMTA with 20 percent provided by local authorities in Atlanta and Fulton and DeKalb counties (Figure 1). The Research Chamber is located immediately south of the main Peachtree Center Station cavern, and is in part an enlargement of the pre-existing Pilot Tunnel excavated to provide bidders on the CN-120 contract a view of the rock conditions (Figure 2). The Research Chamber lies some 3 meters above, and is approximately parallel to, the twin Running Tunnels. The Research Chamber is 18 meters long and has the same 5.5 meter diameter horseshoe shape design dimensions as the twin Running Tunnels.

Jan 1, 1979

By James W. Evans

It appears that all extractive processes involve, at one or more points, fluids (gases or liquids) and that the flow of the fluid is an essential part of the functioning of the process. Usually that flow is turbulent and the turbulent flow frequently determines the rates of mass and heat transfer as well as other important phenomena such as bubble/droplet breakup and coalescence, particle suspension, etc. Over the past decade many attempts have been made to model turbulent flows in metallurgical unit operations. The present paper summarizes some of that work. Amongst the operations considered are agitated leaching, ladle metallurgy, electrowinning/refin- ing, induction furnaces, Hall cells and electro- magnetic casting. Where possible, comparisons are made between model predictions and experimental results.

Jan 1, 1990

By Hans W. Brodbeck

The Advisory Conference on Tunnelling of the OECD, held in Washington, D.C. in June 1970, has established the following definition: "Tunnelling refers to the construction by any method of a covered cavity of predesigned geometry whose final location and use are under the surface, whose cross-sectional area is greater than 2 square metres". (1) The definition makes clear that the term includes all types of underground construction, be it in hard rock, soft ground, under mixed conditions, underwater, etc. Small-sized tunnels in rock therefore constitute but one part of the tunnelling scene. With an ever-growing urbanisation taking place in industrialized as well as developing countries, the demand for small-sized tunnels is, however, rapidly increasing and requires a far-reaching mechanization of excavation and support functions. This trend is accentuated by the fact that small-sized tunnels are far more labor-intensive than large ones, and, with wages raising at a much faster rate than costs for plant and equipment, this will accelerate the introduction of new tunnelling systems. SMALL-SIZED ROCK TUNNELS The main field of application for a tunnelling system for small sized hardrock bores is thus defined. It is in fact the numerous relatively short tunnels required under cities and other populated

Jan 1, 1974

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By J. Derwin King, Harrison R. Cooper

Applications of nuclear magnetic resonance (NMR) offer possibilities for on-line sensing of the concentrations of several elements in flowing sample streams. In addition to hydrogen, these elements, generally of low-order atomic number, include aluminum, phosphorus, fluorine, sodium, boron, and lithium contained in minerals having commercial importance. Many such elements have been difficult or impossible to successfully measure on-line using the more familiar X-ray fluorescence and neutron activation analysis techniques. The availability of practical on-stream analysis methods is essential to applying advanced controls to processes incorporating these elements. On-stream NMR instrumentation has been demonstrated in the past for several process applications including, as an example, coal flow and analysis; and the technology has recently been extended to the measurement of phosphorous BPL in Florida beneficiation plants. The technique involves simultaneous sensing of proton (hydrogen) and 31P intensities to provide data for continuous calculation of BPL in the phosphate through calibration to volume fractions of water and solids. Initial operating results are described using the PhospholyzerTM on-stream phosphorous analyzer designed for plant application.

Jan 1, 1990

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By J. K. Mokka, P. D. Rao, H. K. Lin

Extensive exploration has resulted in delineation of a massive sulfide district on the north flank of the east-central Alaska range. The district covers approximately 400 mi2 and contains numerous stratiform, transposed and some replacement type sulfide deposits ranging in size from less than 1 million st to 20 million st. Five types of ores were sampled for the study. Mineralogical analysis revealed that the minerals are too fine grained for conventional grinding and beneficiation. Hydrometallurgical studies were conducted using ferric chloride as a lixiviant. Ore microscopic studies as well as electron microprobe analyses of minerals in the raw samples and leach residues explained the low recoveries for certain elements as well as sources of impurities that need to be eliminated from the process streams.

Jan 1, 1992

By H. Lyn Bourne

This is the 12th year for this column and the 11th in which the royalty data have been tabulated. This year adds 20 to 30 new entries. There are, however, some deficiencies that the readership hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. There are several states where no royalty information was available for either commodity. Readers can help share information about these missing states, so next year there will be fewer states without information. Severn Brown again sent helpful information from the Prospectors and Developers Association of Canada (PDAC). The summer 1992 issue of PDAC Digest recommended"... the most useful technical paper ever published for economic geologists...." "Net smelter return models and their use in the exploration, evaluation and exploitation of polymetallic deposits" was written by R. Goldie and P. Tredger (Geoscience Canada, Vol. 18, No. 4, pp. 159-171). Last year's column described leasing practices in Russia. Some new information has been gathered since then. Kirill Kavun is the managing director of the International Geoeconomic Center in Moscow. He sent two publications from 1992-"Regulation on the procedure of licensing the use of the subsurface," and "Law of the Russian federation on the subsurface." Both are supplements to the magazine Mineral Re¬sources of Russia, Economics and Management.

Jan 1, 1993

By Colin C. Harris, Jie Zheng

While applications of stirred media mills for fine particle production have continued to increase, there is a lack of understanding of operating behavior and power requirement. Investigations in laboratory stirred media mills have been carried out with grinding media, limestone and yttria stabilized zirconia. The torque required to rotate impellers immersed in dense particulate media with supernatant versus impeller rotational speed displays four regions marked by sharp transitions: transition from static to dynamic friction; channel- ling; dispersing; and centrifuging. Equations, including dimension- less group correlations of power and modified Reynolds number, for relating power, speed, impeller and tank dimensions and design, media size and density, solid concentration, and other relevant variables have been established. Scale-up guidelines with respect to power consumption are also proposed. The best operating conditions for grinding limestone in the laboratory stirred media mill have been identified. Complexation by the polymer during ultrafine grinding of zirconia has been found to cause extraction of yttrium into solution with possibly significant changes in the surface chemical composition of the product.

Jan 1, 1995

By G. T. Adel

This paper presents the highlights of a general-purpose simulator for mineral processing plants that is being developed at the University of California, Berkeley. The state-of-the-art structured design methodogy based on a top-down design approach is being used to construct a modular and completely structured simulator such that it is independent of the unit operation models and routines. The simulator provides for two levels of operation allowing prebuilt or user-built simulation flowsheets depending upon the degree of computer knowledge expected of the user. The philosophy used in designing this simulator appears to be unique in the field of flowsheet simulation. The paper also includes a mini-example demonstrating the usage of the simulator.

Jan 1, 1982

By Odd E. Hanssen

In April 1982, the contracting Companies, ABV of Sweden and Hoyer-Ellefsen of Norway forming the Consorcio Escandinavo Agoyan, signed the contract for the construction of the civil works of the Agoyan Hydroelectric Project, located in Ecuador, South America. The project is located in the Andes mountain region of Ecuador - one of the smaller countries in this part of the world, located on the Pacific Coast. The contract was signed with the Instituto Ecuatoriano de Electrificación (INECEL), a public institution in charge of the development of all major energy producing projects in Ecuador, for a value of approximately US$ 120,000,000. The contract's main elements are - Concrete gravity dam with a total volume of approximately 210,000 cu m. (60 m wide x 45 m maximum height, 320 m crest). - 2,400 m of headrace tunnel, interior diameter of finished lining 6 m of which 450 m is in-situ tunnel formed in a trench. - Pressure shafts, 132 m long, the lowest meters with sheet lining, the rest with concrete lining. - Powerhouse cavern with an excavated volume of approximately 25,000 c m in which two turbines of 78 MW each will be installed. - Two 140 m tailrace tunnels with a finished diameter (concrete

Jan 1, 1985

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002

By Jukka Pukkila, Pekka Särkkä

Intensive co-operation between mining industry and mining machine manufacturers during an eight year program Intelligent Mine™ led to a new concept for applying automation technology in mining to improve the productivity and safety of mines. 'The results of the program are now implemented in several mines in Finland and with similar ideas as well elsewhere in the world. The degree of optimal automation of an intelligent mine depends on several technical and economical factors. The basic precondition for the approach is a clear improvement in total economy of the mine.

Jan 1, 2002

By I. Iwasaki, H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothabiliry tests and SEM observations. In the absence of sodium silicate, Ca I+ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: 1) the removal of impurity minerals and calcium-bearing precipitates from quartz surfaces by dispersion, 2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and 3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1991

By M. J. Rex, K. L. Wiley, D. S. Ramey

In situ leaching, initiated in 1986 at the San Manuel Mine, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development and implementation of in situ well construction methods, formulation of suitable well pattern arrays and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in situ leaching program has become a viable and cost-effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in situ leaching methods that are currently used have been progressively expanded and continually developed. They will become the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management and future plans for the increased extraction of copper by in situ leaching methods at the San Manuel Mine.

Jan 1, 1995