Search Documents

By Bruce R. Sutherland, Jim B. Ramsden, Gerry L. Bolton

Conductive metal powders are important building blocks for today's micro-electronic circuitry. Formulated into inks, they provide the interconnects needed to complete a complex integrated circuit and the means to enter the world of miniaturization. Traditionally, the inks have been based upon expensive metals such as silver, palladium, platinum and gold because of their excellent electrical conductivity and resistance to corrosion and oxidation. The use of a copper based ink, as an alternative to precious metal inks, recently has received considerable attention. Instability in the prices and limited supply of certain precious metal systems have driven up production costs, making the development of a lower cost copper system more attractive to manufacturers. However, lower production costs are on1 y real ized if performance and reliability can be maintained. While the development has been driven by cost, copper does offer some significant performance advantages over noble metal systems: conductivity as good as silver and 4W better than gold; leach resistance better than silver and equal to gold; stability at high frequencies better than gold or silver; strong film bonding characteristics; and compatibility with most solders. These benefits, however, do not come without cost. The inherently reactive nature of pure copper, while providing unique performance properties, makes it difficult to process. Unl i ke precious metals which can be fired in air, copper would oxidize and so requires special furnaces and atmospheres. Despite these difficulties, the transition from precious metal thick film systems to copper is gaining momentum. Manufacturers of high density, high performance circuitry are exploring the performance advantages of copper over gold and silver and the manufacturers of consumer products are considering the potential cost savings of copper over silver-palladium. Sherritt has developed a fine copper powder for this industry. Through association with the ink manufacturers, it has been found that performance properties of the ink vary with the physical and chemical characteristics of the powder. Production Process The production of very fine copper powders at Sherritt is based upon the disproportionation of cuprous ions as outlined in Equation [1] (1).

Jan 1, 1990

By D. R. Babich, E. R. Bauer

Noise-Induced Hearing Loss (NIHL) continues to be a concern of the mining industry. A new noise standard (30 CFR, Part 62) is aimed at reducing NIHL in mining through engineering and administrative noise controls. However, the difficulty and expense of implementing engineering controls can make administrative controls an attractive alternative for reducing worker noise exposure. Over the last three years, the National Institute for Occupational Safety and Health (NIOSH) has conducted worker noise exposure surveys in underground and surface coal mines and coal preparation plants. The surveys revealed numerous possible administrative controls and an approach to implementation and analysis. The surveys have shown that worker dosimetry, time-motion studies, and equipment noise profiling are important aspects of effectively utilizing administrative controls. A description of the approach for selecting, implementing, and evaluating administrative controls, and a list of administrative controls, are reported.

Jan 1, 2004

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By Gordon R. S. Smith

This paper is in two parts. The first part describes Membrane Back-Pulse Filtration and the effects of very short filter downtimes on cycle filtration rates. Part II describes the use of Membrane Back-Pulse Filtration for combined thickening and polishing soda ash thickener feed material followed by a description of computer modeling of CCD circuits by Iterative solver.

Jan 1, 1991

By Robert A. Westin

Polychlorinated biphenyls (PCBs) are a group of chlorinated chemicals that were used in many different fire resistant hydraulic fluids, heat transfer fluids, and in electrical equipment as dielectric liquids. PCBs were manufactured primarily by Monsanto Chemical Company under the tradename Aroclor, and were used by many different electrical equipment manufacturers. PCBs are noted chiefly for their extreme chemical inertness. This resulted in exceptional fire resistance and long life in applications involving exposure to high temperatures and intense electrical fields. This combination of properties resulted in PCBs being widely used in electrical equipment used in mines, including transformers, capacitors, and some electric motors. PCBs were also used as working fluids in some heat transfer and hydraulic sys terns. The same chemical resistance that gave PCBs long life in industrial applications give PCBs essantially eternal life when they are released into the environment. PCBs are not highly toxic in the sense that exposure does not cause immediate health problems. However, PCBs accumulate in the human body and neither degrade nor are eliminated from the body, and long-term exposure to PCBs can result in changes in liver function which may increase susceptibility to the carcinogenic effects of other chemicals. PCBs also accumulate in the food chain; the concentration of PCBs in fresh water fish may be several hundred thousand times as high as in the water the fish are taken from.

Jan 1, 1981

By M. Sadegh Safarzadeh, Erich U. Petersen, Jan D. Miller

"An acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2•4H2O, PbSO4 and Cu0.47Fe0.53SO4•H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 hours with a sulfuric acid-toconcentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different concentrations. The purpose of this paper is to present our examination of the effects of sulfuric acid dosage on the extractions of Cu, Fe, and As from an enargite concentrate. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.IntroductionThe occurrence of enargite (Cu3AsS4) in copper ores and concentrates and the associated high arsenic values in such resources have resulted in a considerable decrease in the demand for such concentrates because they cannot be economically processed using conventional technologies such as smelting and atmospheric leaching (Mihajlovic et al., 2011). The exploitation of such problematic deposits through competitive treatment strategies will be required in the near future in order to satisfy increasing pressure from the copper market. It is expected that the average arsenic grade of copper concentrates will increase from 0.17% in 2008 to 0.22% by 2020 (Mayhew et al., 2011).The acid bake-leach process was identified and selected for further investigation at the University of Utah as a possible process alternative for the treatment of enargite concentrates. In this case, adequate amounts of concentrated sulfuric acid are mixed with the concentrate and heated to the temperature range 150-300°C. Subsequently, the baked material is leached with water/weak acid and the acid bake-leach process has some advantages over conventional sulfuric acid leaching (Prater et al., 1970). During water leaching, metal sulfates are released in solution, after which they can be extracted through well-known hydrometallurgical techniques. While the majority of the work has been done on oxide minerals, there is a limited record of sulfuric acid baking of sulfides."

Jan 1, 2015

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By S. Daniel Thompson

In underground coal mining, the specification and control of belt and bunker capacities are complicated by (1) stochastic and intermittent conveyor loading, (2) a limited ability to reduce surge at the mine face, and (3) occasional overlapping of loading from two or more mine faces on the conveyors. Recently, because of longwall mining and other factors, the capacity requirements of most mine conveying systems have risen substantially; as a result, efficient capacity design and control have become important mine planning issues. This paper reviews these design issues and their associated modeling procedures. Design considerations and modeling difficulties are also examined.

Jan 1, 1996

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country&apos;s largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By Mike O’Brien, Rob Croll

The Evolution of AngloGold -Incorporated in 1944 under the name of Vaal Reefs Exploration and Mining Company Limited -Name changed to AngloGold Limited in 1998 as the vehicle consolidating the gold interests of Anglo American Corporation -Diversification (geographic and orebody) through the sale of low-margin, deep level, short-life assets and the acquisition of higher margin, open-pit and shallow underground operations

Jan 1, 2003

By Jim Dunn

For decades many of us who are associated with the mineral industry have tried to show the public its economic and strategic importance. Some of the mineral industry&apos;s proponents have been politically powerful figures and have been widely quoted. Yet, as measured by public opinion, legislative support, or almost any other standard, our efforts have been inadequate. It is apparent that a set of environmental beliefs that discredit industry, firmly held by a number of idealistic persons, has had wider coverage in the media and in schools than has the mineral industry&apos;s message. Although the fervor of our idealistic friends is often unfounded and, their stands unscientific, they must be considered seriously. Unless we address the issues in terms the idealists will understand, the mineral industry will have little influence on them or on the general public. A. striking thing is that, quite often, translation of idealists&apos; views into action has been counterproductive. The reason is obvious. Excessive amounts of money and energy have been spent on relatively minor problems. The common result is that larger problems have been created. It may be possible to help anti-industry idealists understand their own dependence on minerals, and thus render their views more realistic, if they are shown more effective ways to reach their stated goals. If those goals can be shown to be held in common by all sensitive human beings -- including those in business and industry - the dialogue becomes one of how to achieve common ends. Individual mining companies acting by themselves have little possibility of success, and companies working in unison through trade associations have not been successful. Further, it is unlikely that industry in general can be successful in changing minds unless it seeks outside help. But friends among those who influence public opinion have been hard to find. Historically, help from media has proven difficult to get. Nor has enough help from educators been forthcoming. Yet, a war is going on in the technological, philosophical, and political trenches, even though much of the public is not aware of it. For the first time in years, there is row a significant and growing number of eloquent and brilliant thinkers on the side of free enterprise and industry, many of them environmentalists, but without the anti-industry mind-set. They have had remarkably little help from the private sector or even from the present administration. Industry may do far more for itself in the long run by encouraging these brave but bruised individuals and their organizations than by trying to work alone. These friends of free enterprise are working against a seemingly stacked deck relative to much of the media, the bureaucracy, and the educational system. However, despite their problems, their success to date has been remarkable. With more cooperation from industry they should do even better.

Jan 1, 1987

By Meili Zhu, Qingpu Shi

High temperature, methane, dust and other disasters are getting more serious with mining depth getting deeper and the development of mechanization in underground mines. An application of a descensional ventilation to a coalface is one of the effective measures to solve the above problemes. The descensional ventilation is an venttilation that an airflow in a coalface wouuld downflow along an inclination of a coalface and the direction of the airflow is the same as coalflow. Since 1960&apos;s, the descensional ventilation has been applied to 171 coalfaces in 46 coal mines of 23 coal mine administrations in China, such as Pingdingshan , Zhongliangshan, Pubai, Huangshi coal mine administrations. Among the 171 coalfaces, there were 104 coalfaces taking 60.8% in gently inclined seam. The coalfaces in inclined seam and steep seam were individually taking 18.7 % and 20.5 %. There were 77 coalfaces taking 45 % of the total in low gassy coal mines and coal and methane outburst mine were individually taking 17% and 38%. There were 141 coalfaces taking 82.5% of the total in potential danger of dust explosion. There were 125 coalfaces taking 73.1% of the total in potential danger of spontaneous combustion. Therefore, the descensional ventilation can be used in coalfaces under different conditions in China. The practice at home and abroad shown that the application of the descensional ventilation to coalfaces has obvious results in dust control, temperature control, preventing methane accumulation at top corner angle and control of spontaneous combustion in goaf. To more safely and reliably apply the descensional ventilation to coalface and to provide a way for the development of mine ventilation technology in China, the paper will have discussions on the following problems: METHANE EMISSION AND DISTRIBUTION AT COALFACE WITH DESCENSIONAL VENTILATION Methane emission in a coalface with a descensional ventilation is an argued issue for many years. Base on the coal practice, special similar model tests and researches in China, the followings are our main comments. The Descensional Ventilation can Reduce the Methane, Accumulation at the Top Corner Angle. The measurements in six coalfaces with the downward airflow in Qinhemen Mine, Fuxin Coal Mine Administrations shown that the methane concentration at the top corner angle is often up to l% when the coalface has the upward, airflow. The max. methane concentration at the top corner angle is about 0.49 to 0.7% when the coalface has the descensional ventilation. Therefore, with the descensional ventilation, it basically solved the overlimited gas concentration at the top corner angle which is a potential danger to coal production. Because the direction of upfloating gas is opposite to the direction, of the descensional airflow, the descensional ventilation; could increase a turbulent flow mixing capacity of the methan gas and air, and reduce a possibility of methane; accumulation. Due to an air leakage in goat when the coalface with the descensional ventilation lower than an air leakage in goat when the coalface with the, ascensional ventilation, a less methane quantity will release from goat at the descensional ventialtion. It should be pointed out that due to a higher air leakage at ascensional ventilation and the direction of the air; leakage same to the direction of the natural upfloating methane in goaf, those will cause a large methane; accumulation at the top of the goaf and easy bring about, methane accumulation and overlimited methane concentration at the top corner angle with an ventilation vortexflow at the top corner angle. On the other hand, because the direction of the upfloation force function is upward, the descentional ventilation could minimize as possibility of methane accumulation at top corner angle in coal with the descensional ventiltion.

Jan 1, 1991

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson&apos;s ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

This chapter contains the edited transcript of the "Gold Heap Leach Information Exchange" session that was held at the 1990 SME/AIME Annual Meeting in Salt Lake City, Utah. The exchange occurred on the afternoon of February 27, 1990. The session was intended to act as a forum for discussing some of the more prominent operating problems associated with heap leaching precious metals. The information exchange was very successful. The exchange consisted of several panelists introducing and discussing different topics, follow by a comment and question period. This transcript contains the panelists&apos; presentations as well as comments and questions from the floor and the panel. Extraneous comments and remarks have been edited out. Some wording has been changed for clarity, but the transcript is basically an accurate account of what was said. At the end of the transcript are two papers submitted as part of the panel discussion

Jan 1, 1990

By B. Pesic, J. E. Wey

Introduction One important class of manganiferrous ores is manganiferrous-silver ores. They occur in the oxidized portions of the silver deposits of the western United States. Silver is often associated with manganese oxides, which in some ore deposits are dispersed through calcite, causing the black color of the host rock, known as black calcite. Black calcites can occur in carbonate rocks (0.3 to 50 kg Ag/t) and in volcanic rocks (less than 30 g Ag/t). Silver mineralization associated with manganese oxides and black calcites can occur in veins (Hewett, 1968) or as disseminations (Graybeal, 1981). In the US, silver-bearing manganese veins are located in a broad arc that extends from southern Colorado to southwest New Mexico, southern Arizona, and southeast Califor¬nia (Hewett, 1964). Areas of disseminated silver-manganese mineralization include the Creede and Silver Cliff districts of Colorado and the Tombstone and Hardshell districts of Arizona (Graybeal, 1981). These deposits are also characterized by significant amounts of silver halides - cerargyrite (AgCl), bromargyrite (AgBr), and iodargyrite (AgI). Black calcites are also common in these deposits. Oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. In the past when these ores could not be smelted, they were treated generally by cyanidation at very low efficiency. The US Bureau of Mines (USBM) studied the problem of treating silver-manganese ores in the early 1920s (Clevenger and Caron, 1925). It was found that the refractory silver in the original ore was insoluble in all the common solvents for metallic silver and its salts. The conclusion was that to obtain the highest recovery of silver, all the manganese had to be dissolved or the higher oxides of manganese reduced to manganous oxide. More recent results from treating refractory silver¬manganese ores were given by USBM (Scheiner et al., 1973). The silver ores from Candeleria District, NV, and Round Mountain District, CO, were investigated. Electrooxidation experiments recovered only 34% silver with minor amounts of manganese dissolved. Sulfurous acid pretreatment followed by cyanidation revealed that silver extracted was proportional to the amount of SO2 used. A similar approach, using sulfurous acid pretreatment followed by cyanidation, was also proposed by Rhoades et al. (1984). Hazen Research Inc. performed extensive testing on silver and manganese dissolutions from Ag-Mn ores obtained from the Candeleria and Round Mountain ore deposits. The methods examined were direct cyanidation, pretreatment with sulfurous acid followed by cyanidation, malonitrile leach, and leaching with ammonium hydroxide-sodium thiosulfate under slight oxygen pressure. The results were not satisfactory. The importance of the vast reserves of Ag-Mn ores and the lack of an efficient method to recover these metals warranted a search for new technologies. One novel method for extraction of these metals is treatment of Ag-Mn ores with acidified thiourea solutions. Preliminary results of the leaching of silver and manganese from Ag-Mn ores were very encouraging (Pesic, 1984a) ; thus, it was decided to examine the new lixiviant in more detail. Experimental Ore from the Round Mountain District was studied. It was crushed, ground, and dry sieved into monosized fractions in the range of 16 to +400 mesh. The ore composition was about 90 g Ag/t and 3% Mn, depending slightly on size. The leaching experiments were performed in apparatus described elsewhere (Pesic, 1982 and 1984b). All experiments were performed at constant temperature conditions. The leaching residues were analyzed for silver and manganese. Atomic adsorption was used to analyze the solution samples and fire assaying to analyze the leaching residues (for silver). The standard experimental conditions are given in

Jan 1, 1987

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By G. Machiavelli, P. Bevilacqua, G. Ferrara, T. P. Meloy

During several years of operation in Europe, South Africa and other locations, the Tri-Flo process has demonstrated substantial improvements in dense-medium dynamic-separation systems. The reasons for this improvement are: • a high-sharpness separation due to the multistage system and the application of new concepts in the design of the regeneration circuit and in the control of the medium Theology, and • the possibility of performing two cuts at different densities using a single separation device and a single regeneration circuit. This paper discusses the above points in detail with particular reference to the multistage technology (based on the circuit analysis theory) and to the control of the medium rheology (based on recent work in the modeling and simulation of the rheological behavior of dense suspensions). Concerning the multidensity separation, information is given on the new three-stage separator where the high-density separation is performed by the first stage and the low-density separation is performed by the second and third stages. This configuration (already realized in two operating plants) was selected because no particular sharpness was required at the high-density separation, while high sharpness was required at the low-density separation. However, the configuration can be inverted or a fourth stage can be added (at very low additional cost) to provide two stages for each separating density. The importance of achieving a high sharpness separation is related to minerals (industrial minerals in particular) where the density difference of the phases to be separated is very low (as in processing of lithium ores, feldspar- and others). Information is provided on plants operating in South Africa and Canada, for the beneficiation of lithium minerals and on a plant under construction in Italy for the beneficiation of feldspar. Finally, the importance of making the separation at two densities is emphasized with particular reference to coal; i.e., producing a low-ash premium coal and recovering, in the middling, a by-product without losing heating value. Also, very important for some minerals is the production of a high-grade concentrate (at the first stage) suitable for sending directly to metallurgy (e.g., chromite ores) and the production of a low-grade concentrate that can be further treated. In this way, a higher overall recovery of the valuable mineral can be achieved, and, at the same time, a reduction of the treatment costs can be obtained. All of the above applications were once considered impossible.

Jan 1, 1995

By John C. Gould

GENERAL DESCRIPTION The Climax mine is located 161 km (100 miles) southwest of Denver on Fremont Pass astride the Con¬tinental Divide. Climax employs 2800 people to pro¬duce 42 670 t/d (47,000 stpd) of molybdenum ore. The Storke level, the main underground level, produces 19 970 t/d (22,000 stpd); the 600 level, the lowest ac¬tive underground area, produces 7260 t/d (8000 stpd); and the open pit presently produces 15 430 t/d (17,000 stpd), Fig. 1. A panel caving method is possible because of the favorable geology and geometry of the Climax ore body. Geology The Climax deposit is composed of three separate ore bodies formed in a massive Tertiary stockwork which penetrates Precambrian granites and schists. The ore bodies are elliptical in plan with overall dimensions of 914 x 1219 m (3000 x 4000 ft). In section the ore bodies are arcuate with an overall height of 457 m (1500 ft), although the depth is not firmly ascertained. Ore grade decreases rapidly into a highly siliceous cen¬tral core and more gradually toward the outer bounda¬ries of the deposit. The mineralization is relatively continuous in the ore zone and contains few dilution-causing waste inclusions. Molybdenite is contained in pre-ore fractures which were largely recemented during the three mineralization pulses. Postore fractures, with a spacing of a few inches to several meters (feet), render the deposit amenable to caving when it is undercut. The peripheral rock caves similarly to the ore, but the central core is competent and is difficult to cave. Caving Feasibility Successful caving action requires an undercut area of approximately 122 by 122 m (400 by 400 ft). When the undercut area exceeds this minimum distance, the arching effect is lost, and the ore column collapses. Ore extensions from the main cave area less than 122 m (400 ft) wide usually cannot be caved. Waste or low¬grade areas within the deposit can be left if they are large enough to carry weight around openings passing through them. Experience indicates that these areas should be over 30 m (100 ft) in length and width. Smaller unprofitable units of waste, such as postore dikes, are mined to avoid weight problems and result in ore dilution. Successful caving and ore recovery are dependent upon timely ore removal from the undercut zone because columns of immobile ore inhibit caving and concentrate weight onto the underlying workings. Climax experience indicates that a finger (drawpoint) spacing* averaging 10.4 m (34 ft) yields an excellent caving action and a 92.5% ore recovery at the estimated grade. An additional 15% of the ore is recovered-at a diluted grade (Fig. 2). Mine Layout The slusher drift is the primary production facility (Fig. 3). The ore is undercut and caved into the fingers,

Jan 1, 1982