Search Documents

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015

By S. Mojeddifar, N. Ostadmahdi Aragh, M. Hemmati Chegeni

This work integrated selective principal component analysis (SPCA) with a singularity fractal model to map hydrothermal alterations of argillic, phyllic, and propylitic in the north-west of Kerman city in Iran. SPCA results were provided for short wave infrared (SWIR) bands of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor tomap phyllic and propylitic alterations. Also, the bands 5–7 were applied to map the argillic alteration zone. SPCA results could present useful information for alteration mapping but it does not show the purest pixels of alteration. Therefore, a fractal model of singularity was applied to highlight the different alteration pixels in the Kerman Cenozoic magmatic arc (KCMA). Thus, the singularity index of different hydrothermal alteration zones was produced. Comparing the obtained results with the field data showed that Kader, Serenu,Meiduk, and Abdar deposits were acceptably identified by alteration mapping. Also, it seems that the singularity index could not discriminate the hydrothermal alterations of argillic and phyllic. The same spectral signature of kaolinite and muscovite minerals is the main reason for misclassifications.

Jul 20, 2020

By Yaxiong Wang, Yong Li, Yuedong Wu, Haigang Dong, Jiachun Zhao

A roasting-leaching process has been developed for concentrating platinum group metals (PGM) from a PGM-containing ferroalloy. The optimized roasting conditions used a NaOH-to-ferroalloy mass ratio of 1.2 at 600 °C for 2 h. The roasted product mainly comprised Na4SiO4, NaFeO2 and Fe2O3. The iron oxide and sodium silicate associated with the roasted product were leached in water and dilute sulfuric acid solution, while the PGM was concentrated in the acid-leached residue. A PGM concentration of 23.4% was obtained with assaying, and the concentration factor of PGM from the ferroalloy to PGM concentration was greater than 9.

Jun 14, 2021

By Shamim A. Dar, & Samsuddin Khan, & K. F. Khan, Mohd Shuaib

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By R. G. Graber

Field testing of GPS mining applications has confirmed the technical and operational viability of GPS for precise, centimeter-level positioning in harsh taconite environments. GPS hardware has provided consistent availability exceeding 90%, with precision in certain applications of ± 0.07 foot at 95% confidence levels. Despite these technical successes though, challenges persist in achieving effective GPS integration. These challenges include the acceptance of new job tasks by mine personnel, the capacity of typical mine data communications infrastructure and the need to design GPS interfaces for new mining equipment.

Jan 1, 1998

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization's structure that addresses the immediate and long-term impact of a company's products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By P. Grotjohann

In processing heavy mineral sands, the low feed concentration and respective high value of the desired minerals require high capacity production and sharp classification/separation techniques to reduce the specific production costs. The allflux® separator, a new process system introduced to the heavy mineral industry, meets these criteria in an economical way. Its two-stage process, a combination of rising current and fluidized bed technology, allows the treatment of extremely high massflows in a single unit. Using concepts that have proven successful in processing concrete sands for many years, testwork in coal, iron ore, and heavy minerals looks very promising.

Jan 1, 1998

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By H. R. Thompson

The Grant Town Power Plant is a nominal 80 MW (net) Waste Coal-Fired Electric Generating Plant which is located in northern West Virginia, approximately 15 miles southwest of Morgantown. The Steam Generator consists of two (2) Pyro-Power Circulating Fluidized-Bed Boilers (CFB), each rated at 400 000 lbs/hour @ 1,350 psig. Main Steam. The Turbine Generator is a single GEC Ahlstrom unit rated at 95 MW gross and 80 MW net. The Plant began commercial generation during April, 1993. The facility is owned by American Bituminous Power Partners, L.P. (AmBit), and operated by Mission Operations and Maintenance, Inc.

Jan 1, 1996

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By A. Spearing

According to a 2000 NIOSH report, about 100 million rock anchors are installed annually in coal mines in the USA. Most coal mines have conditions that are conducive to corrosion of the rock anchor and ancillaries (such as plates), yet the effect of this on the performance of the anchors has not been adequately researched and its effects are not understood or quantified in the USA. There is considerable research into corrosion in civil engineering applications on surface and underground but the corrosion of coal mine rock anchors is not necessarily the same because: ? In underground civil structures, water ingress is usually stopped as part of the construction process. ? Many rock bolts in mines are only partially resin grouted leaving part of the reinforcing member exposed to corrosive conditions. All cable bolts in coal mines are only partially resin grouted. ? Even when mine bolts are fully grouted, shrinkage cracks occur and the rock stresses can change due to adjacent mining that can cause the resin column around the bolt to fracture further under external shear or tensile stresses. Most coal mines therefore have ideal conditions for bolt corrosion.

Jan 1, 2010

By W. C. Patrick

Introduction The availability of a thorough, simple-to-use roof fall classification system is desirable for several reasons. First, such a system would expedite the reporting of falls for the purposes of estimating material removal costs, analyzing damage levels, and complying with federal regulations to report falls in certain areas of the mine. Second, the classification system would allow the mining engineer to record falls routinely with little time and effort expended. This would encourage him to make observations concerning what type of roof support would work best in a given situation. Third, and probably most important, an adequate roof fall classification system is the first step toward developing a means of predicting the occurrence and extent of future falls. It was with these three reasons in mind that the following classification system was developed. The type of classification chosen reflects the background of the developer and the intended purposes of the system. Hylbert has proposed a geologic-based classification which groups falls as to structural and compositional origin. The need for similar systems is noted by Cox and by Ferm and Melton. Each of these researchers is confronted with a situation requiring a relationship between local geology and roof fall occurrence. Such a relationship would allow the prediction of the relative frequency of falls from a knowledge of local geologic features. The current research is aimed at fulfilling somewhat different requirements, as noted above. Fall geometry has been chosen as the basis of the classification system so fall type can be reported independent of local geological, environmental, and tectonic conditions. This approach parallels that used in the common slope failure classification with groups failures relatively independent of

Jan 1, 1977

By G. R. Coonan

A number of famous studies have shown that house damage relates better to peak particle velocity than to acceleration or displacement. The relationship is true but doesn't go far enough. Why, for example, can construction shots go well above 1.0 or 2.0 inches per second without reportable damage? Recent studies have shown that vie must look at frequency and duration of an event in addition to amplitude. The complexity of measuring frequency, duration, and amplitude makes the average blaster in the field shudder. An even more excruciating problem is the need to obtain such data inside the building or residence in order to accurately predict the damage potential or human response to nearby blasting. The author reviews current research programs and suggests new areas of research necessary to help maintain a balance between complicated research requirements and simple field measurements.

Jan 1, 1980

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022

By Stryker Magnuson

While probe drills are not strictly necessary for all projects, the incorporation and use of probe drills and pre-grouting adds capability and insurance to boring operations. Water ingress and unstable ground can be resolved before becoming a problem and resulting in costly delays through the use of enhanced, 360-degree probe drilling setups. To do this, proper design of the array of drill ports in the shield, matched to the possible ground conditions, is critical. For ground with exceptional water and instabilities expected, additional probing locations are low-cost additions that can lower risk and increase efficiency. In this paper we will look at recent and ongoing projects including the Lower Meramec Tunnel and Jefferson Barracks Phase 2. We will detail the design of those probe drill arrangements, and our overall recommendations for probing/grouting systems that best suit challenging ground conditions and keep projects running smoothly.

Jun 13, 2023

By R. O. Vernon

The Florida Peninsula has existed as a part of a much broader plateau, since at least the Early Cretaceous. This plateau, the Floridan Plateau, now consists of the present peninsula and a broad submerged shelf of equivalent size extending the length of the state and out into the Gulf of Mexico. Florida Peninsula was separated from the mainland United States by a negative area called the Suwannee Straits. To the south of this feature existed an environment similar to today?s Bahamo Banks where very pure calcium and magnesium carbonates with associated evaporites were deposited. Thus the Eocene and Oligocene contain little or no quartz sand or clay minerals except in the Panhandle west of the Suwannee Straits where some clastics were contributed by rivers from the north.

Jan 1, 1966

By William Gleason

During the 116th National Western Mining Conference and Exhibition in Denver, CO, the host city was often referred to as world?s mining capital, so it was fitting that the conference looked at the mining industry through a global lens. In the current world economy, the mining industry must keep a sharp focus on such things as commodity prices and global supply and demand as well as local issues that can have a dramatic impact on a mine?s social license to operate. In short, companies should mine locally but think globally. During the three-day conference at the Colorado Convention Center, a range of global and local issues that effect the industry were discussed. A record 1,144 people attended the conference.