Search Documents

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By E. Kurt

The field of percussion rock drilling is subdivided into two areas of application; that which takes place on the surface and that which takes place underground. Surface drills are used in quarrying, highway construction, and maintenance work; underground equipment in mining and tunneling work. Two basic principles are involved in the operation of all percussion drills. First, the principle that reciprocates the impacting piston and second, the principle that causes the drill steel and bit to rotate. The back and forth motion of the piston is accomplished by a self-acting automatic valve that admits air alternately to each end of the piston (Figure 1). Drill steel and bit rotation is imparted by an integral ratchet mechanism (Figure 2) in the so-called "rifle bar" machines (Figure 1) or by a separate pneumatic motor in "independent rotation" drills (Figure 3). While rock drills are subject to all kinds of physical and operational abuse, they are most sensitive to faulty lubrication. Proper lubrication is the single most important factor in the longevity of a percussion drill.

Jan 1, 1970

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By M. E. Mellado

In this paper, we present an a posteriori validation of a heap leaching analytical model using sensitivity analysis. The model is suitable to represent the process of heap leaching of solid reactants from porous pellets and is based on a combination of the leaching kinetics at two levels: particle and heap. The validation is simple, and a sensitivity analysis can easily be performed. The simplicity of the analysis provides insight into the control and optimization of the heap leaching process without strong mathematical complexities. The model and the corresponding sensitivity analysis include the effects of heap height, particle sizes, flow rates and several operation-design variables. Using a case study, we discuss the importance of model validation based on sensitivity analysis. We also comment on several choices for optimizing the process. We had three goals in this work: a posteriori validation, highlighting the importance of model validation and providing insight into optimization choices. We can conclude that the model has good internal logic and there are no extra variables; i.e., all of the variables in the model are necessary.

May 1, 2012

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By D. R. East

The concept of sub-aerial tailings deposit.ion using a managed rotational deposition system to form a deposit of partly-saturated tails for North American conditions was introduced by Knight and described by Knight and Haile (1983). The application of the sub-aerial technique, together with continuous removal of all surface waters and underdrainage outflows from the Key Lake uranium mine I s tailing storage facility in Northern Saskatchewan, Canada, has been documented by Knight and Haile (1984). Since then, the concept is being applied in the United States to tailings facilities in California, Nevada, Arizona, Utah, Colorado, Idaho and South Dakota.

Jan 1, 1989

By G. M. Bernard

An overview presentation of the fast-track start up of Cerro Colorado, a new copper heap leach project in Chile's Atacama' desert. A brief explanation 'of location of the property, exploration history, geol-ogy, reserves and development are presented. The overview includes mining, crushing, agglomeration, and the solvent extraction-electrowinning recovery process. Challenges and requirements specific to heap leach systems will be addressed and analyzed. A detailed description will be given of the mobile heap leach conveying and stacking systems used in the building of heaps for on-and off-pad operations.

Jan 1, 1995

By J. Bartrum

Semi-autogenous, (SAG), milling operations can realize substantial Increases in mill throughput by removing and crushing critical size, slow grinding, material from the SAG mill. Full-scale plant testwork showed that modifying the Kidston SAG/ball circuit to a semi-autogenous-ball milling-crushing (SABC) circuit would increase plant throughput by 25 to 30%. The methods used to determine the value of the SABC circuit and the design of the circuit are discussed.

Jan 1, 1988

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By Virginia T. McLemore, Devlon R. Shaver

Clinkers are the result of a seam of coal catching fire and burning the surrounding rocks. The fires caused the surrounding rocks to be baked at high temperatures, removing organic material and partially forming glass. These rocks become hard, orange, and brick like, forming clinker. The purpose of the study is to determine their potential to contain economic levels of critical minerals, including Rare Earth Elements. Some clinkers contain over 200 ppm total REE.

Feb 1, 2024

By Frederick A. Subosits

The Lithium Corporation of America's Hallman-Beam spodumene-pegmatite open pit mine is located in the Kings Mountain area of North Carolina. Figure 1. Presently this area of North Carolina is the lithium center of the U.S., if not of the whole world. The Lithium Corporation mine was started in 1968 and now covers 61,000m2 (15 acres) with projected are reserves in excess of 20 years. Lithium occurs at the Hallman-Beam property in a mineral known as spodumene (LiAlSi2O6), a lithium aluminum silicate. The run-of-mine are averages 1.43 Li2O. Figure 2 of the general Mining Division flow sheet follows the concentration of the Li2O to 5.5% and also lists the various by-products that are sold commercially. The unique properties of lithium have led to many commercial applications, some of these including lubricating greases, ceramics, glasses, glazes, welding fluxes, aluminum reduction cells, dehumidifying and air-conditioning equipment, sanitizers, polymerization catalysts, batteries, and pharmaceuticals. (3) (5)

Jan 1, 1978

By G. S. S. Raman, M. S. Klima

The effects of pressure and cake thickness were studied using a split-plot design for pressure filtration of a fine refuse slurry obtained from a bituminous coal preparation facility. Pressure filtration offers the potential to significantly reduce the moisture content of the fine refuse stream with the addition of little to no flocculants, thereby minimizing the volume of refuse stored in impoundments and providing a recycle water stream for use within the plant. Experimental results showed that the final cake moisture decreased with increase in pressure and decrease in cake thickness. In addition, specific cake resistances calculated for the various tests indicated an increasing trend with increasing pressure and decreasing cake thickness. With increase in cake thickness, an increase in cake moisture and the weight of solids deposited in the cake was observed. An ANOVA analysis indicated that both cake thickness and pressure significantly affected the cake moisture, while only cake thickness statistically influenced the weight of solids in the cake. A regression model was developed with an R2 value of about 0.99 to relate cake thickness, the single largest statistically significant factor, with the weight of solids in the cake. Filter capacities were calculated in terms of the solids deposited per unit time based on a product specification of 25 percent cake moisture, and it was observed that the thinnest cake had the highest filter capacity.

By Robert R. Unterberger

The purpose of this paper is to summarize the research of the past sixteen years on three distinct methods of probing into solid rock. The first method is to use radar of the appropriate frequency. The second method is to use sonar. The third method is of recent vintage and uses techniques of nonlinear sonar also known as parametric sonar. The first two concepts, that of radar and sonar, are common to most people. Very few have heard of nonlinear sonar. Each of the probing techniques were investigated in order to overcome deficiencies in the former technique. Each has its advantages and disadvantages. It should be emphasized that all of these techniques for probing (or seeing) into rock are used in mines, and generally speaking not from the surface. Only in very special cases, such as certain very dry parts of Egypt or Peru, or, for example, the surface of the moon, will these probing techniques work from the surface. The reason for the development of these probing techniques has been to alert miners to possible hazards ahead of mining. Such hazards may be (1) old (unknown) boreholes connected with high pressure water zones above, (2) fractures that might connect to the Gulf of Mexico above the mine, (3) water-filled fractures that threaten the safety of miners, or (4) the discovery of dry faults ahead that can disrupt the planning of future operations.

Jan 1, 1983

By W. C. Bagby

The Dee disseminated gold deposit is the northernmost mine in the Carlin gold belt. We analyzed soil samples £ran undisturbed areas overlying the deposit to determine the usefulness of soil geochemistry in identifying ore zones. The depth of sampling ranged from 12 to 14 inches, depending on soil development. The -80 mesh fraction was analyzed by atomic absorption for Au, As, Sb, Hg, and T1 and by semiquantitative spectrographic analysis for Ag. Highly anomalous Au, Kg, As, Ag, and Sb are most closely associated with ore zones whereas T1 is more broadly dispersed. Hg is the only element that identifies deep ore.

Jan 1, 1984

By J. G. Davis

Continental Oil Company has spent over four years of research on the fundamentals of potash solution mining. This work included laboratory investigations of salt solution, brine flow, selective extraction of KC1 from sylvinite, and control of cavity geometry. Laboratory results were expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well mining systems were studied in the field work. The current paper discusses one field test in which potash was solution mined from a thin sylvinite ore zone in the Carlsbad Potash Basin. A two-well mining system was used for this test. The potential economic value of solution mining has been recognized for many years, and applicable United States patents date back into the past century. Principal advantages of the process over conventional mining include (1) the use of drilled holes and solution techniques in- stead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths.

Jan 1, 1969

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

By G. B. Michaels

Exploration programs for mineral resources often involve analysis of soils or stream sediments for the mineral being sought or its pathfinders. Because many metals are toxic to microorganisms, patterns of metal resistance in soil or aquatic populations may provide additional useful information at a reasonable coat. These patterns in some cases have been more effective than the soil geo-chemistry and may be easier to obtain. Elevated levels of resistance to silver and its path-finders have been demonstrated in stream populations from an area of known silver deposits, and resistance to gold pathfinders has been demonstrated for gold-bearing areas. Uranium has also been located by this method.

Jan 1, 1989