Search Documents

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By Harvey P. Knudsen

Case studies are presented in this paper to illustrate the usefulness and applicability of using conditional simulation in under- ground coal mine planning. Conditional simulation is a technique developed in the last five years that allows the building of a simulated ore body (or coal deposit) model. Construction and validation of the simulated model is described in order to show how well the model reproduces the essential characteristics of the deposit. In the model, the thickness, ash, and sulfur content are known everywhere in the deposit and each variable has the same mean, variance, and spatial variability (variogram) as that variable has in the real deposit. Use of the simulated deposit in the design of drilling strategy for long range mine planning is demonstrated in me case study. Determining the potential of short term production scheduling to reduce the fluctuations of sulfur in run of mine coal is described in the second case study.

Jan 1, 1980

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By H. Marshall Farrier

In the past few years the world petroleum industry has increasingly felt the weight of changes in the principal economic factors affecting pro¬fits. As a result of, these changes, it has been necessary for many oil companies to acquire certain new facilities in order to strengthen their competitive positions and thereby protect their tremendous investments in crude oil reserves, pipe line facilities, refining operations, and marketing outlets. Principally these needs have been met by new capital outlays. A supplementary, method of acquiring needed facilities, however, has been to obtain existing facilities through complete or partial acquisition of other companies.' properties. It is this method of meeting competitive pressures with which this paper is concerned. This paper presents a statistical breakdown of the mergers and acquisitions which occurred in the oil industry between January 1, 1954, and October 1, 1959, showing the frequency' with which certain types of properties were acquired in each of the years studied. In addition, it discusses the principal economic conditions which stimulated many of these property trans¬fers, comments on the effects of these mergers on the consuming public, and indicates the types of, mergers and the rate at which they may be expected during the next three or four years. The basic data upon which the statistical analysis presented in this paper is based were taken from several published sources. Obviously they are somewhat incomplete because not all mergers and acquisitions were reported However;, a careful search was conducted through, The Wall Street, Journal, The Oil and Gas Journal, Potroleum Week, and The Oil Daily with the result that the data should be reasonably complete and comparable for each of the years studied, It is believed, therefore, that the statistical analysis which' follows provides a reasonably accurate indication of the general trend in mergers and acquisitions during the period studied.

Jan 1, 1960

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By İsmail İnce

The purpose of this study is to investigate the index-mechanical properties of igneous rocks by using the electrical resistivity method. Electrical resistivity, index (P-wave velocity, dry density, and porosity), and uniaxial compressive strength values of 48 different igneous rock samples were measured in the laboratory. Simple regression analysis was performed between index-mechanical properties and electrical resistivity values. Strong exponential and logarithmic correlations were found between electrical resistivity and the index-mechanical properties of the igneous rock samples.

Jan 21, 2022

By A. W. Dickerson

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research, Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Jan 1, 1997

By O. Lopez

"Stringent regulations and increased arsenic presence in ore bodies being exploited have created the need for cost effective and environmentally compliant technologies to remove selenium and arsenic from mine waters and metallurgical waste streams. Existing treatment methods have high life cycle costs and/or produce residues that, due to their unknown stability over the long-term, may represent future liabilities. This results in high compliance costs and uncertainties which negatively impact existing operations and projects in permitting. Selen-IX™ is a new ion exchange based process that selectively removes selenium from mine impacted waters down to 1 ppb while producing a stable inorganic iron-selenium product. Results of piloting completed on streams generated from coal and copper-gold deposits are presented along with preliminary equipment sizing and life cycle costs of full scale treatment. An example of a commercially available system for arsenic removal using sulphide precipitation is presented. The benefit of this treatment method is discussed based on recently completed technical feasibility assessment including laboratory testing and preliminary engineering design. INTRODUCTION Selenium Due to the chemical similarity between selenium and sulfur, selenium substitutes sulfur in many minerals that can be found in a wide range of deposits including coal, base metal, precious metal, phosphate, and uranium. One of the main environmental challenges facing the industry in North America today is related to the removal of hexavalent selenium, e.g. selenate, to ultralow levels, typically between 1 to 10 ppb, from large flows of often cold water containing less than 1,000 ppb of selenium. Recent studies commissioned by the industry identified biological selenium reduction systems as the best available technology. Although the biological selenium reduction process is commercially proven in certain applications to remove selenium to ultralow discharge levels, the technology has been primarily applied to relatively low and constant flows of warm water produced by the Flue Gas Desulfurization (FGD) scrubbers in the power generation industry. The wide spread adoption of this treatment method by the mining industry is hindered by high capital and operating costs associated with treating large flows of cold water, lack of data and knowledge about the long term stability of solid residues produced by this treatment, and limited capacity of biological systems to respond to sudden changes in flow and/or mass load of contaminants. Furthermore, it has been reported that reaching discharge limits less than 3 ppb could be a challenge and that polishing treatment for the removal of BOD and phosphate maybe required to avoid the impact of the biological treatment which requires organics and nutrients, on aquatic environment downstream of treatment plants. Alternate treatment systems are being developed to overcome and/or completely avoid some of the challenges of biological systems. One such treatment system is BioteQ’s Selen-IX™ process which is purely physico-chemical treatment system."

Jan 1, 2015

By A. B. Holland-Batt

Following a relatively static period in the 1960s and 1970s when incremental development rather than innovation was the norm for gravity separation, the last 15 years has seen a number of new developments in this area. The paper briefly reviews the traditional gravity separation techniques and then examines the newer developments such as centrifugal separators. Particular emphasis has been placed on novel devices or improvements that offer either better control or improved performance.

Jan 1, 1998

By Michael Vitale, Lee W. Abramson, Daniel McMaster, Andrew J. Thompson

"Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on four recently constructed rock tunnel projects in New York, Ohio, Georgia and California. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed. INTRODUCTION Tunneling is a risky business. More than ever, attention is being paid to the risks associated with tunneled facilities and implications on project or program cost and schedule. Questions about why tunneling projects notoriously exceed budget numbers abound. Evaluations in retrospect and going forward have focused on the wide breadth of inherent risks associated with tunneling. More and more, these risks are being identified, studied and managed to a higher degree. As more and more scrutiny pervades the industry, little value is being obtained and leveraged on future projects. The industry seems to be headed in a direction of making the same mistakes over and over. The notion of risk evaluation has been around for decades and received wide notoriety with the U.S. Space Program and ambitious projects in the energy industry such as hydropower and nuclear power in the 1960s and 1970s (Stewart and Melcher, 1997). This led to the evolution of tunnel risk analyses with more rigorous identification of the unique risks in tunneling projects impacting cost and schedule. As tunneling risks became more readily identified, more attention has been paid to the frequency and impact of the occurrences unique to tunneling (ITIG, 2012). Currently, few tunnel projects are being planned, designed or constructed without a formal risk register that identifies the risks, mitigates the risks and quantifies the probable impacts of risks that cannot be mitigated. In hind sight on many recent projects, events that brought projects to “its knees” were not addressed in risk assessments or were not dealt with to adequately mitigate the risk of these events."

Jan 1, 2016

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont USA (Newmont) in Nevada was faced with such a need in their Carbon-in-Leach (CIL) train. In a collaborative effort between Newmont and Derrick Corporation, tests were conceived to assess the viability of drop in replacement screen using a three dimensional screen panel. The urethane pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade their urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing, and other scalping applications.INTRODUCTION In Spring of 2014, Process Machinery Associates (PMA), Derrick Corporation’s (Derrick) local area representative, met with Newmont USA (Newmont) to discuss the operation of the in tank screens in the carbon in leach (CIL) train at Twin Creeks, near Golconda, Nevada. The process was originally designed for 13,000 +tons per day (tpd) but has been steadily rising since the plant was commissioned and now Newmont requires 16,000 tpd to be processed. The original screens were running at their maximum capacity and Newmont required additional screening capacity to continue the upward trend in production. Physical separation by use of screening is one of mineral processing oldest methods. Screening media can be prone to blinding and pegging and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and therefore larger machines, screening media that doesn’t blind, or a combination of both. In an effort to avoid larger machines, Derrick Corporation had been working on a revolutionary three dimensional panel which would add non blinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 (Carlin, Nevada) in July of 2013 and was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

The past decade has seen remarkable progress by the railroads both in equipment and concepts in the handling of dry bulk. materials. While such shipments have always been an important part of the traffic handled by the railroads I little was done to improve the efficiency of handling or toward attempted optimization of equipment design before 1960. Several developments at about that time turned attention to this important segment of railroad traffic. One was the construction of a successful coal slurry pipe-line. Another was the promise of substantial economy in electric power transmission by ultrahigh voltage systems and finally, came the growing technological and economic feasibility of nuclear fuel electric generating plants. Each of these developments was a threat to the coal traffic of the railroads --the most important single commodity they handled in terms of revenue and tonnage. By the mid-1950's I Southern Railway management had become most concerned with its growing investment in freight car equipment and the declining revenue productivity of the capital employed. Additionally I there was substantial concern with the loss of business and potential losses in the area of the railroad's greatest economic advantage --bulk commodity movements. In 1958 a small team was established to study this problem. They arrived at two conclusions. The first conclusion was that within limits of maximum gross allowable weight on rail the lowest unit net capacity cost of investment came at maximum allowable gross weight per car unit. The second conclusion was that with a high degree of utilization costs per weight unit transported could be reduced to the pOint where

Jan 1, 1971

By K. V. Raj, A. Miller

"Workers at mineral processing facilities are often exposed to high levels of dust generated when ores are processed. Crushing, grinding, screening, and other processes generate large quantities of dust, which can exceed the threshold VALUES (prescribed by the Mine Safety and Health Administration (MSHA). Many ores contain quartz (silica), which has been known to cause serious health problems in workers over time. Given the structure of mineral processing plants, the airflow regime is not coherent inside the building, which may lead to multiple recirculation zones. These recirculation zones can trap dust, and concentrations of dust can then rise over time. Therefore, there is a need to understand the airflow phenomenon that occur inside of mineral processing facilities and how these occurrences interact with the dust generation processes to identify zones of potentially high dust concentration. Computational fluid dynamics (CFD) modeling can give a better understanding of the airflow and help recommend designs and methods to mitigate the high dust concentrations in a mineral processing plant. This paper presents the CFD modeling of airflow inside of a mill building to demonstrate airflow patterns that will affect the generation and subsequent dispersion of dust due to crushing, grinding, and other activities. This study was conducted by researchers from the National Institute for Occupational Safety and Health (NIOSH). INTRODUCTION In a mineral processing facility, minerals go through various mechanical processes in order to reduce their size for separation of economic minerals from gangue minerals to produce a final marketable product. This research, conducted by the National Institute for Occupational Safety and Health (NIOSH), focuses on ore mills in metal and nonmetal mining (MNM) operations, but the applicability of the approach will be valid for any large structure where workers are exposed to airborne contaminants. The processes of crushing, grinding, cleaning, drying, and product sizing in these facilities generate a large amount of dust, creating hazardous conditions for the workers in these facilities. This is highlighted by the fact that MSHA sampling data for the years 1997–2012 indicate that 12.3% and 15.9% of the gathered samples were over 100 µg/m3 for silica for metal and nonmetal mills, respectively [1]. Mineral processing operations typically use some type of engineering control to address their most significant dust sources. Engineering controls include such approaches as bag-house-type dust collectors, scrubbers, and electrostatic precipitation [2]."

Jan 1, 2018

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017