Search Documents

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By William P. Lorenz

Overlying the sulfide mineralization at Anamax Mining Company's Twin Buttes Mine is an oxidized zone up to one hundred meters in thickness. The principal copper minerals in this zone are chryso-colla, tenorite, cuprite, native copper and copper-manganese-iron wad. This ox¬idized zone also contains minor amounts of uranium ranging in concentration from 0.002 to 0.010 percent. Since pit development through 1980, some 38 million tonnes of oxide ore with copper contents greater than 0.6 percent have been brought to the surface. Copper in the oxide ore is extracted at Twin Buttes in, an agitated sulfuric acid leach plant followed by solvent extraction and electrowinning producing 90 tonnes per day of copper cathode. During leaching of the oxide ores small amounts of uranium are solubilized along with the copper values. This is not limited to Twin Buttes as most acidic copper bearing leach solutions throughout the southwestern United States contain small amounts of uranium.1

Jan 1, 1982

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By S. G. Axen

Design of wells for in-situ leaching is based on individual mining operation and ore deposit requirements. Major design considerations are well flowrate, depth, fluid composition, expected well life, mine operating plan and cost. A large variety of downhole equipment, materials of construction, contract services and methods of well completion and stimulation are available. A generalized design procedure which allows the engineer to optimize well design for a particular ISL application is described.

Jan 1, 1988

By Francisco J. Escandon V.

Numerous lead-zinc-barite-fluorite ore deposits, with simple mineralogy and roughly concordant with bedding, are found widely distributed all over the world, having been denominated and well described as "stratiform deposits" or "strata-bound ore bodies", not having any genetic relationship. During several years, its origin has been discussed, without getting to general agreement regarding the main mining districts of this type. Through studies made of large stratiform deposits in the United States, Europe and Russia, it has been found that there are, within this classification, syngenctic diagenetic and epigenetic ore bodies. During the Symposium about the genesis of the stratiform lead-zinc-fluorite-barite deposits, carried out in New York in 1966, Frank G. Snyder (1), presented an excellent analysis of the theories of the origin of these deposits and of the evaluation of the criteria regarding classification. As per his definitions (Table 1), "a deposit is syngenetic if formed by processes similar to and simultaneously with the enclosing rock, epigenetic if introduced into a pre-existing rock and a diagenetic origin implies deposition of metals with the host sediments but with recrystallization, rearrengement and limited migration".

Jan 1, 1974

By K. Anim, C. Calderon-Arteaga

Located in Mojave, CA, The Soledad Mountain mine is an Open pit Heap-Leach gold Mine, which is operated by Golden Queen Mining Company LLC. under private capital. Open pit mining began in 2015 while full production was reached in 2016. The open pit mine feed a processing plant that can process more than 13K tons per day of ore which is sent to a heap leach pad. The Soledad Mountain project is a poly metallic deposit with Au and AG being recovered as payable metals. As the mine became bigger after moving to the east pit phases, Golden Queen was facing new challenges to control the production and accurately determine KPIs to improve/increase the production. To maximize returns and asset value, a new fleet management system (FMS) was adopted and implemented. The new FMS has enabled the mine to interconnect the different stages of the mining, as well as to recognize issues and implement the necessary corrections. With the associated increase in complexity in the process, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery. Implementation of new daily and weekly plans were needed to ensure the ore delivery and meeting the tonnage goals, while allowed the equipment operators to better geolocate and to maximize the equipment production. These conditions alongside with Golden Queen’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route the material from the mine, is critical to site success and some of these challenges have been overcome by the adoption of the new FMS, the implementation of daily and weekly plans and upgrades in the ore control workflow. Examples of how the integration of the new systems allowed golden Queen to improve production strategy, are discussed in this article.

Mar 2, 2022

By D. Mannino, M. Townsend, E. Daniloff, E. Petsonk

Nonspecific airway hyperresponsiveness is a central feature of chronic obstructive pulmonary disease and has been associated with atopy in the presence of environmental exposures such as smoking. Coal miners may develop emphysema and lung function decrements related to their dust exposure. To investigate the roles of airway responsiveness and atopy in these effects, we evaluated the relationships among smoking, a history of hay fever or seasonal rhinitis, and airway responsiveness (AR) in a group of underground bituminous coal miners and nonmining controls. All subjects had a normal baseline percent predicted FEV1. Increased airway responsiveness was defined as a 15% or greater decrease in FEV1 following methacholine inhalation. 85 miners (45%) and 99 controls (46%) were current smokers, 59 miners (31%) and 55 controls (26%) were lifetime nonsmokers; former smokers were excluded from further analysis. Overall, 25% of 144 miners included in this analysis had increased AR, as opposed to 29% of 155 controls. Thirty-seven percent of both miners and controls had a history of seasonal rhinitis. Significantly fewer miners (15%) had a history of hay fever compared to controls (25%, p< 0.05). Figure 1 shows the prevalence of increased airway responsiveness in miners and controls in association with hay fever. In both smoking and non smoking miners the presence of a hay fever history was significantly (p < 0.05) associated with a higher prevalence of increased AR. Little effect was seen in smoking (p = 0.827) and nonsmoking (p = 0.940) controls. Figure 2 shows a similar higher prevalence of increased AR associated with symptoms of seasonal rhinitis in the mining group. This was significant (p < 0.01) only in the smoking miners. No effect was noted in the controls. These data suggest that the association of a history of hay fever or seasonal rhinitis symptoms with increased airway responsiveness may be more common in coal mining, compared to non-dusty occupations. Although the implication of these data are unclear, further study of miners with a history of hay fever or seasonal rhinitis is warranted. (Supported in part by Grants G1135142 and G1105142, US Bureau of Mines, Generic Mineral Technology Center for Respirable Dust)

Jan 1, 1991

By Yasutaka Izumi, Tuneyoshi Funasaki, Keizou Miki, Makoto Kanai

INTRODUCTION The Tokyo metropolitan region, inclusive of the three neighboring prefectures (Kanagawa, Chiba and Saitama), has the highest concentration of population and industry in Japan; with an area of 13,500 km2 or only 3.6 percent of the national land, but a population of 31.8 million or 26 percent of the national total, and a Gross Regional Product (GRP) of146 trillion yen (US$1.33 trillion) or 36 percent of the overall GDP of Japan as of 1990. Tokyo Bay, embraced by the metropolitan region as shown in Figure 1 (a), (b), is open to the Pacific Ocean as a marine gateway and is ringed by large cities and coastal industrial zones together with port facilities, all constituting a concentration of prime importance for socio-economic activities. The Trans-Tokyo Bay Highway (TTB highway), which crosses Tokyo Bay and provides a direct transportation link between the west and east sides of the bay, has long been a sort of “dream-come-true” project in Japan. As shown in Figure 2, linked to the Tokyo Bay Shore Highway, Metropolitan Inter-city Expressway, Tokyo Outer Ring Road, Tateyama Express-way, and others, it will play an important role as an integral part of the regional highway network to help promote spatial redistribution and multi polarization of urban functions, thus strengthening cooperation between cities and restructuring the metropolitan region. The TTB Highway is a project of 15.1 km in length designed as a toll highway to cross the bay by tunnel and bridge, and will require ten years to complete at a total cost of more than 1,438 billion yen (US$13.077 billion). Following more than 20 years of feasibility and environmental assessment studies, construction of this giant offshore highway project commenced in May 1989 as the first large-scale highway project with private-sector participation under the prevailing Road Law in Japan, and is now steadily proceeding toward the goal of completion in fiscal1997. This report outlines the entire TTB Highway project, including the waterproofing measures against high water pressure and the rapid construction method applied in the construction of shield tunnel sections.

Jan 1, 1997

By D. E. Healy

In 1989, an autogenous grinding task force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding (SAG) at the National Steel Pellet Plant in Keewatin, MN. Pilot plant test work, performed by the Hanna Research Center (HRC), indicated that fully autogenous grinding with pebble extraction and crushing could be incorporated into the existing circuits. In 1990, one of the existing 10 grinding mills was converted for an in-plant test incorporating pebble crushing. Full-scale test work were conducted in 1990 and 1991. They verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit using pebble crushing being greater than throughput of the existing SAG mill circuits. The plant produces 5 Mt/a (4.9 million ltpy) of iron ore pellets from 17.6 Mt (17.3 million It) of crude taconite. Crude ore is single-stage crushed by gyratory crushers. Primary grinding is performed by 10 semi-autogenous wet grinding mills. Secondary grinding is performed by five ball mills. Induration is with an Allis Chalmers grate-kiln pelletizing system. The primary grinding circuit consists of 108.2-m-diam x 5.5-m long (27 ft-diam x 18-ft) SAG mills. The mills are charged with 127 mm-diam (5 in.diam) steel grinding balls at from 3% to 5% by volume. Ball consumption rate is about 0.55 kg/t (1.25 lbs/lt) of crude ore feed to the mill. Each SAG mill is powered by two 2.6 MW (3500 hp) motors drawing 5450 kW (7300 hp) at 76% of critical speed. The mills are grate discharge with 16 mm (0.6 in.) slotted grate openings when new. The mill discharge is sized on a trommel screen having 4.5 mm (0.2 in.) openings. The plus 4.5 mm (+0.2 in.) oversize material is returned to the discharge end of the mill by a reverse screw auger located in the center of the trommel. The -4.5 mm (-0.2 in.) trommel screen undersize is pumped to magnetic cobbers.

Jan 1, 1992

By Robert G. Lundquist

REAM (for Rapid Excavation And Mining) is a method of rock fragmentation by high-velocity projectile impact developed by Physics International Company. This paper reports the results of field testing over the last two years. The success of the method is based on the fact that the amount of rock broken per shot scales nonlinearly with projectile impact energy. Thus, high energy impact yields spectacularly low specific energies for rock breakage. The field work reported used 90- and 105-mm military guns to accelerate 8-1/2 and 10-pound concrete and steel projectiles to velocities of 5000 to 5500 fps. All tests were performed in a competent 25,000 psi granodiorite at Hope Valley, California. During the first year of field testing 26 feet of 13-foot-diameter tunnel were produced with the 105-mm gun. The first 20 feet of this tunnel were line-drilled to aid in producing a stable portal. During the second year the tunnel was extended an additional 29 feet using the 90-mm gun. The 55-foot tunnel was produced by 590 shots. Between 1-1/4 and 1-1/2 tons of granite were broken by each shot. A silenced 90-mm gun was placed underground and the tunnel portal closed with a steel barrier. Overpressures of less than 1 psi were measured on the inside of the barrier, corresponding to an impulse noise of about 170 db. The muck produced was similar to drill and blast muck. Overbreak and ground support problems appeared to be less than with drill and blast. The contour of the tunnel was easily controlled using the 90-mm gun; the tests were also conducted using a 57-mm gun for trimming. Projections indicate that advance rates with REAM will be three to seven times faster than drill and blast, at less than two-thirds the cost. This is based on the development of a fully integrated continuous system and an inexpensive propellant giving a total expendables cost of less than $3 per shot. Other applications of the REAM technology are found in secondary breakage for open pit mining, in drilling large diameter holes, and in underground mining for longwall mining, overhand stoping, and raising.

Jan 1, 1974

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By Duk-Won Park

Since geologic anomalies are one of the governing factors of instability of underground openings, it is extremely important to know in advance the locations and extent of these anomalies such as faults and weak zones. At an underground coal mine in the Black Warrior Basin, core drilling was conducted to find a fault in an area where they were planning to locate longwall panels and possibly a shaft. Core logging did not provide sufficient information to delineate the exact location, strike, and dip of the fault. However, a high resolution reflection seismic study successfully solved this problem. This experience proved the seismic exploration technique could be used for premining coal exploration by reducing drilling costs and providing more accurate and detailed information about geologic anomalies.

Jan 1, 1988

By G. Montgomery

This is a summary of what has happened to the domestic production of two industrial minerals vital to a healthy US economy: fluorspar and barite. A few years ago we were self-sufficient in both minerals and good ore reserves still exist. FLUORSPAR Some 9% of the fluorspar presently being consumed in the US is imported, whereas the use of fluorspar has not declined proportionately. Several factors can be mentioned.

Jan 1, 1986

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By D. Carr, C. Anderson, M. Deal, C. Larson

"Construction of the OceanaGold Haile operation’s process plant in Kershaw, South Carolina is currently under way, with ore through the mill expected in late 2016 and commercial production expected in early 2017. The process is designed to treat 6,350 tonnes per day with minor upgrades required to achieve 8,270 tonnes per day. Plant optimization during detailed engineering, combined with a focus on de-risking the process, has resulted in numerous process changes since the initial design. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio operation, whilst identifying potential expansion opportunities. INTRODUCTION Haile Gold Mine is located in Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching from 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that delineated 2.02Moz. of gold in reserve at an overall grade of 2.06 g/t. OceanaGold acquired Romarco Minerals and the Haile Operation in October of 2015. OceanaGold operates under a risk management philosophy in all aspects of operation, both corporately and at each individual business unit, and has implemented numerous process changes to eliminate or mitigate risks identified in the initial design of the processing circuit, and provided increased opportunity for optimization and expansion. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio Operation, and identifies potential expansion opportunities. INITIAL PROCESSING CIRCUIT DESIGN An extensive metallurgical test work program was undertaken by Romarco Minerals and third party laboratories during the initial design phase of the Haile project [1]. This preliminary test work provided the technical information as a basis of plant design. The initial flow sheet for the Haile processing circuit is shown in Figure 1 (see APPENDIX). The plant is designed to process 6,350 tpd (7,000 stpd) on an annualized basis. The process begins with a jaw crusher followed by a SAG and ball mill grinding circuit to reduce particle size to P80 74 µm. A flash flotation cell treats 50% of the cyclone underflow in the ball mill circuit. Grinding circuit product is sent to a rougher flotation circuit to recover gold-bearing pyrite. The flotation concentrates from flash and rougher flotation are reground to P80 13 µm using stirred media detritors (SMD’s). The rougher flotation tail is pumped to the carbon-in-leach (CIL) circuit for gold recovery. The reground concentrate is pre-aerated prior to being pumped to the CIL circuit. The CIL circuit is a hybrid circuit with eight tanks. Tank 1 leaches the pre-aerated concentrate only, and tanks 2 through 8 leach the combined flotation tailing and tank 1 discharge. The carbon strip circuit is a standard pressure Zadra system, followed by electrowinning, and refining using an induction furnace. CIL tailing passes through a cyanide recovery thickener prior cyanide destruction and then pumped to the tailing storage facility (TSF)."

Jan 1, 2017

By D. Baker

Alternative material handling methods are allowing material handling operations to be performed with increased cost savings. This allows for higher production levels with better returns. RAHCO International Inc.&apos;s Continuous Mining Excavator (CME) has recently received a lot of attention due in part to its operating efficiency, flexibility, and associated low operating costs. The CME is designed to perform three primary functions. These include material excavation, sizing and loading operations. In many applications, a drilling and blasting process can be eliminated. The CME was developed originally in 1985 for open pit coal mining. See figure I. Since this time, it has been proven an effective system for excavating many other types of materials including friable and sticky materials. It has also been shown to suitably handle hard rock in certain site conditions.

Jan 1, 1998

By Michael H. Vallez

On September 13, 1973 MAPCO Inc. leased from Pocahontas Land Corporation an 18,000 acre tract of coal lands in Eastern Kentucky&apos;s Martin County (See Figure 1.). In July, 1974 initial run of mine coal shipments commenced and in April, 1976 shipments of a 12,500 BTU, less than 1% sulphur, washed coal was being shipped. Results of exploration demonstrated that large quantities of overburden would have to be moved. MAPCO decided to invest in large surface mining equipment to tackle the job.

Jan 1, 1981

By Bobby P. Faulkner

Allis-Chalmers has combined a new heat transfer device, called the ROLLER GRATE, with a unique processing scheme, resulting in the ROLLER GRATE Oil Shale Processing System of Allis-Chalmers. In order to test both the process and the equipment, a batch Process Development Unit (PDU) ROLLER GRATE retort was designed and built. This unit vas designed with the flexibility to process shale over a wide range of test conditions in order to demonstrate the attributes of the oil-shale processing system. Instrumentation on the PDU and extensive sampling of the effluent streams permitted the PDU test data to be used in the design and scale-up of the process. Over 30 tests have been conducted with Colorado shale, and over 25 tests have been run with an Indiana shale. In addition, rests have been run with California and Utah tar sands.

Jan 1, 1983

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982