Search Documents

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By G. L. Merritt

The implementation of the Surface Mining Control and Reclamation Act of 1977 (SMCRA) has evolved into one of the most complex environmental protection programs to come out of the late 1970's. The level of detail in the statute and the regulations have resulted in a rigid and complex set of requirements for the administration, permit-ting, inspection and enforcement of the program. In addition, the constant change of the federal program caused by regulatory changes, reorganization of the Office of Sur-face Mining Reclamation and Enforcement (OSMRE), ongoing litigation involving OSMRE, and the use of the budget to establish additional mandates on OSMRE and the State Regulatory Authorities have resulted in an unstable program. The instability of the program makes it extremely difficult for the States to implement their programs and to achieve the goals of SMCRA.

Jan 1, 1988

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By Douglas Ball

An underground storage field is a gas field where man, not nature, has put all or most of the gas. All but one of those in use today are in the pore spaces or "porosity" of sedimentary rocks, the most common being sandstone. The one exception, near Newcastle, England, is a gas storage in a cavern dissolved from rock salt. The tens of millions of barrels of LPG (liguified petroleum gas) now stored in salt caverns mined in shale is liquid storage, not gas storage, and in this paper I recognize the presence of these installations but do not include them in the gas storage category, Since, with the English exception, gas storages are gas fields, they can all be sorted into the categories used to describe gas fields, 95% of them once gas fields anyway, but some of the remaining 5% are the ones having the greatest effects on underground waters.

Jan 1, 1960

By Edward K. Davison

The so-called "construction aggregates," sand and gravel, crushed stone, and several kinds of metallurgical slags, are used principally in the construction and maintenance of all kinds of roads, engineering structures, buildings, homes, airports, etc. Production of these aggregates is approaching two billion tons annually. In terms of tonnage produced, sand and gravel has been the leading mineral since 1954, with crushed stone gradually approaching an equal tonnage. Sand and gravel is of widespread occurrence and of wide variation in suitable gradation and quality. It is a low-value, heavy-loading, short-haul commodity. These characteristics account for the historic concentration of production tonnage in and near urban areas where construction activities are concentrated. The combination of improved urban and near-urban highway systems and the steadily rising rail rates for short-haul traffic has fostered a consistent change since World War II from rail to truck transport, with trucks now accounting for more than 807 of the tonnage moving away from the production sites. While there are increasing numbers of exceptions, truck transport of sand and gravel is generally limited to about 30 miles. The expansion of the urban and near-urban areas of even moderate density, which became so pronounced after World War II, has been the source of most of the sand and gravel industry's environmental difficulties. Dust, noise and truck traffic associated with the operations -- particularly truck traffic -- have, of course, generated public complaint. This has been particularly true in those many cases where housing developments have approached and even surrounded sand and gravel operations which were in operation before the development started.

Jan 1, 1974

By M. E. Rossi, J. A. Bassan, J. B. Novillo

Sampling and geological models are the basis of recoverable resources models. They are pillars of mineral resources and reserves estimation, and what geostatistical methods for grade estimation should rely upon. The resource model is best estimated if geostatistical methods make good use of sound geologic models. Data collection from the original drill holes, including field procedures and the quality assurance and quality control (QA/QC) of those samples are pillar one of a resource model. The second pillar of the model is the good use of the logged geological information, resulting robust geological interpretations, and the corresponding three-dimensional models of those interpretations. These models are partly subjective and mostly conditioned by the quality of logging and the geologist’s experience. They are also conditioned by the quality of the three-dimensional models built, regardless of the modeling method employed, traditional or implicit. Grade estimation is more commonly done by applying some geostatistical method and using the two basic sources of information, data and geologic model. Multiple stages are involved in this process, and in all of them there are uncertainties and risks that have to be dealt with. Knowledge, understanding, interpretation, and management of the model’s fundamentals are critical, given that they directly affect its accuracy and predictive quality. The mitigation of related risks allows for the creation of opportunities, generating value and reducing the project’s uncertainty. This paper discusses some of the key variables, uncertainties, and risks involved in the resource modeling process, illustrating with specific examples; discusses possible risk mitigation alternatives, and proposes best practices to avoid or mitigate those uncertainties. Emphasis is placed on taking advantage of technological advances without ignoring fundamentals. INTRODUCTION In the area of mineral resource estimation, one alarming trend that these authors have observed in the past 20 years or so is that the care and diligence in checking the work as it progresses has generally diminished. This is, perhaps, an unintended consequence of the availability of new technologies and tools that attempt simplify and speed up the work involved. This has led to a more casual attitude towards checks and balances that have to be in place at any given stage of the process before proceeding to subsequent stages, as best practices dictate. To some extent, some of these aspects are covered in international standards for resource estimates reporting (JORC, 2012; CIM, 2010). But these are broad, and do not specifically recommend best practices to a level of detail that would have an impact on certain aspects of the process. There are numerous references in the geology and mining journals and conferences that discuss the consequences of poor recoverable resource models (Baker and Giacomo, 1998; Vaughan, 1997).

Jan 1, 2019

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

By Roger N. Kust

Because ammonia can form complex ions with certain of the transition metals, such as copper and nickel, it has long been of interest to extractive metallurgists interested in leaching or separating these metals. Although it is a relatively expensive reagent, ammonia is amenable to recycle because of its volatility. In development of processes utilizing ammoniacal leaching or separation schemes, information regarding solution vapor pressures, pH and solubility limitations is needed. There is voluminous literature on ammonia-water systems generated by the urea industry. However, frequently the systems of interest to metallurgists differ significantly in concentrations of ammonia used, the temperatures of interest. Furthermore, the differences arising from the presence of metal values in solution must be comprehended. There is surprisingly little information readily available regarding systems of practical interest to metallurgy. As a result, those interested in ammonia-based processes end up either doing expensive laboratory research to obtain necessary data or overdesigning the process. Another approach to obtaining desired information about ammoniacal systems is to attempt to calculate from first principles the various solution properties. This paper is being presented to illustrate what can be accomplished by estimating the state of equilibrium in an ammoniacal carbonate system from available thermodynamic information making simplifying assumptions when needed.

Jan 1, 1976

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983

By Allan E. Hall, Kuda R. Mutama

Jet fan (ductless fan) ventilation in underground mines and tunnels is a subject requiring further attention. At present there are no accepted procedures or guidelines for this type of ventilation. The main reason has been the absence of sufficient general data, which has hampered the development of rules. There is great potential for using jet fans in terms of both effectiveness and economics because they eliminate the need for ventilation tubing. In the present studies a procedure is described and results are presented from a jet fan modeled in a square section wind tunnel. The major purpose of the studies was to provide fundamental data on jet fan performance after it was realized that previous work had been limited and too site specific. The jet fan position in relation to the tunnel walls was varied in order to study the influence of confining walls on entrainment rates and the resulting aerodynamics. A clearer understanding of the fundamental principles of jet fan applications was obtained.

Jan 1, 1995

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By Allen J. Sobczak, Peter J. Peters

The five tunnel contracts of Milwaukee Northeast Side Relief Sewer System are about 80 percent complete. The tunnels are all excavated for 1.9 meter (6'-0") finish diameter sewers in a variable rock, mixed face, and glacial soil environment. Different contracts were let under two primary types of specifications, performance and prescriptive, which treated aspects of construction, such as primary ground support and groundwater control, differently. Interfacing of design and construction through field personnel allowed the needs of all parties to be met and resulted in savings in time and money to the Milwaukee Metropolitan Sewerage District (MMSD). Interfacing, cooperation and risk sharing allowed resolution of problems such as line and grade variations and potential differing site conditions. It also allowed the parties to pursue constructive changes to construction activities. Thus on one contract prescribed use of compressed air was eliminated, but migration of fines into the tunnels was stopped with filter fabric. Use of an expensive primary support system was dropped, but concern about deterioration of lagging was alleviated by use of special materials.

Jan 1, 1983

By James R. Runkle

Studies in eastern Ohio, northern West Virginia, and southwestern Pennsylvania determined whether subsidence caused by longwall mining influences soil moisture and tree growth. Soil moisture was measured both over new longwall panels and over an unmined control area throughout the growing seasons of 1990, a wet year when the panels were excavated, and 1991, a dry year. No significant effects of mining could be detected. Tree growth was studied in two pairs of woodlots. In each pair, one woodlot was located over a longwall panel excavated about 1980 and the other over an unmined area. Differences in tree growth between mined and unmined areas were neither significant (for most species) nor consistent in direction. The above results imply that if mining does have impacts they are likely to be highly site-specific and localized such as by disruptions of springs or soil slippage.

Jan 1, 1986

By Haydn H. Murray

In 1967 a large kaolin deposit was discovered on the Jari River, a tributary of the Amazon, in the territory of Amapa in Brazil. The kaolin occurs in the Barreiras Series of Pliocene age and is part of the Belterra Clay. The kaolin was drilled and tested, and today a modern processing plant is producing over 150,000 tons per year of high quality paper coating clay. Some of the problems associated with the mine development, processing, personnel, and marketing of this remote kaolin deposit are discussed. The mineralogy and physical properties of the Jari kaolin deposit are also described.

Jan 1, 1981

The only good news in the exploration sector in 1982-a year plagued by low metal prices and weak demand-was precious metals. Gold in particular remained in the forefront, as it has for at least the past three years. The reason for this is partially due to gold's seeming resilience to conventional supply side factors-such as new production-that normally influence many other metals. Also, with projected production costs of about $6.40-$9.65/g ($200¬$300/oz), modest deposits with average grades can offer an early return on capital investment and good profit potential. Keeping escalating capital costs for new mining ventures within reason has shifted gold exploration efforts in recent years. Many mining companies are seeking relatively low grade, modest tonnage, near-surface gold mineralization. This, of course, leads to lower development costs using open-pit mining methods. Recent refinements in the carbon-in-pulp recovery process also has enhanced the economics of such deposits. Slumping economic conditions certainly played a key role in shaping exploration activity last year. Nearly every major mineral-producing state recorded exploration slowdowns. In Alaska, for example, development expenditures approached the level of exploration spending for the first time in the state's history. This not only reflects major companies' decisions to move toward production but also the economic slowdown. The worldwide recession stopped Nevada's exploration and mining boom "dead in its tracks," said John Schilling, state geologist. The year was one of layoffs and closings for the state's mines and exploration offices, he reported. Similar trends were noted in most other states, especially in the West and Southwest. In the Pacific Northwest, however, exploration appeared to continue at a relatively good pace considering the metals market. In the mining geophysical community, recent advances in telecommunications and microprocessor technology are continuing to provide a positive impact. Many geophysicists have begun using satellite digital communication links to access computer systems from remote sites where using a microcomputer would be difficult. There were also major contributions made in exploration geochemistry last year. Highlights include progress in formulating mineral deposit models, geochemical exploration in glaciated and arid environments, and publication of many informative books. The following state-by-state summary and articles on geophysics and geochemistry provides a detailed view of exploration events throughout the US in 1982.

Jan 5, 1983

By J. Loredo

The region of Asturias, located in the northwest of Spain, has an extensive mining history; coal, gold, zinc, lead, copper, cobalt, mercury, iron, manganese, fluorspar and others have been extracted from the antiquity. In the Asturian Central Coal Basin, the closure of all open pit coal mines and their restoration, the progressive closure of underground coal mines that is happening from the 1980?s, and the restoration of spoil heaps, provides post mining lands for alternative uses. In relation to metallic mining, the abandonment of all mercury mines without restoration in the 1970´s, has left significant quantities of wastes and mining works. More than thirty years later most of them remain without restoration. In these sites the legacy of the historical mining activities is apparent in the form of shafts, galleries and transversals, old mining installations and spoil heaps. Mine wastes have eventually become important Hg and As pollution sources, resulting in a widespread contamination of the surrounding soils and surface waters. Abandoned mines of other metals such as copper, cobalt, iron, etc. and industrial minerals such as fluorspar, have also left a mining legacy to take into consideration. In this context of declining mining areas, some remedial options have been applied to specific areas resulting in alternative uses as pastures, agro-forestry, industry and socio-cultural activities.

Jan 1, 2008

By Ehsan Moosavi, Kamyar Tolouei

In open-pit mines, the long-term production scheduling optimization problem (LTPSOP) is a complicated problem that contains constraints, large datasets and uncertainties. Due to its dimensions and NP-hard nature, it is usually difficult to find an ideal solution to the LTPSOP. The optimal schedule generally restricts the ore, metal and waste tonnages, average grades, and cash flows of each period. In this paper, to synthesize grade uncertainty into the strategic schedule, a stochastic integer programming (SIP) framework is presented to LTPSOP. The objective function of the SIP model is to maximize the net present value and minimize the risk of deviation from the production targets considering grade uncertainty simultaneously while satisfying all technical constraints and operational requirements. Instead of applying one estimated orebody model as input to optimize the production schedule, a set of equally probable orebody realizations is applied to synthesize grade uncertainty in the strategic schedule and produce a more profitable and riskbased production schedule. To solve the LTPSOP, the hybrid approach with the augmented Lagrangian relaxation method, the Harris Hawks optimization, the Random Forest method and Monte Carlo method was proposed. To indicate the applicability of the model, a case study on a gold mine was implemented. The framework displays the capability to minimize risk and improvement in the expected net present value and financial profitability .

Jun 25, 2023

Lack of selectivity in mixed mineral flocculation can be attributed to one or more of the following factors: dissolved ion interference, heterocoagulation, mechanical entrapment in flocs and entrainment of fines between flocs. In a study of apatite- dolomite system, it was determined that dissolved ions do not have a significant effect on selectivity. Heterocoagulation was minimized by choosing proper process conditions and addition of a dispersant. Mechanical entrapment was proved to be insignificant and efforts were made to reduce entrainment by choosing an appropriate method of separation of flocs from fines. A new factor termed "polymer induced entrapment" which occurs due to limited affinity of the polymer to the mineral which is not flocculated is postulated to be the cause for the loss of selectivity.

Jan 1, 1986

By Lee W. Saperstein

In surface mining for coal, common practice for the disposal of preparation plant refuse is to bury it. As with surface refuse piles, these buried wastes can ignite and can also lead to ground and surface water pollution. Steps to ameliorate these problems have been devised over the years. C and K Coal Company, of Clarion, Pa., the largest Pennsylvania surface mining company, has incorporated all of these steps and added of few, of their own in their latest disposal practice. In addition to layering and compacting, C and K practices selective placement and dilution to minimize longterm problems.

Jan 1, 1977