Search Documents

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008

By J. D. Morgan

Demand for nonfuel minerals depends on the overall state of the economy, which steadily improved each quarter in 1984. New housing starts rose to 1.8 million units. Automakers turned out about 15% more cars (7.8 million) and 30% more trucks (3.1 million) than in 1983. Nevertheless, many domestic mineral operations experienced difficulties in 1984. This resulted from import competition greater use of newer engineered materials, emphasis on multi-unit housing and downsizing of motor vehicles. About 15% of our energy was imported. This in cluded $36 billion worth of crude oil and $22 billion in refined products This added significantly to the overall merchandise trade deficit of $12; billion. On the bright side for mining, coal production rose 14% to 810 Mt (890 mil lion st). Three-fourths o: the coal was burned to generate electricity and more than half of our electricity was derived from coal-burning plants. With the exception of a few large-bulk, low-value raw minerals, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult. Consequently, our nonfuel minerals trade deficit rose 60% to $19 billion, reflecting imports of $39 billion and exports of $20 billion. There were increased pressures from some major segments of the minerals industry for some form of import protection. But President Reagan said, "Our goal is a system of free and fair trade in goods, services, and capital. We will work toward this goal through both bilateral and multilateral trading agreements." The US minerals industry consists of domestic mines, concentrators, smelters, refineries, mineral manufacturing plants, and recyclers. It also includes many wholly- or partially-owned operations in many parts of the world, providing employment and income for US citizens and others as well. Compared with 1983, the value of US raw nonfuel mineral output rose 8%, to $23 billion. The $253 billion worth of goods processed from this crude mineral output was a 14% increase. Major Metals Raw steel production - a major indicator of both material use and mineral production-rose 10%, to 84 Mt (93 million st). This stimulated a 36% rise in domestic iron ore production, to 52 Mt (57 million st), about 98% pelletized. Iron ore imports rose 44%, to 14 Mt (15 million st). Despite the increase of steel production, output remained well below levels of just a few years ago. For example, 1984 production was still 23% less than in 1981. Raw steelmaking capacity remained steady at 122 Mt (135 million st). The industry continued to cite steel imports as a major reason for low domestic capacity. In December, pacts with seven leading steel exporting nations were announced. This is an effort to reduce import penetration to about 18.5% of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 50% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production, at 45 kt (49,500 st), rose threefold. Mine shipments of tungsten, another mineral tied to steel

Jan 5, 1985

By W. G. Pariseau

This contribution describes rock mechanics features of the Davis Cavern at the former Homestake Mine in Lead, South Dakota, U.S.A. The mine is located in the northern Black Hills of South Dakota. In 2003 and again in 2008, the mine site was recommended for development as a national Deep Underground Science and Engineering Laboratory (DUSEL) in cooperation with the Sanford Underground Science and Engineering Laboratory under the South Dakota Science and Technology Authority (SDSTA). The original Davis Cavern was excavated about 9.1x16.8x9.7 m high (30x55x32 ft high) in 1965 (Mitchell 2009) at a depth of 1,478 m (4850 ft). The purpose of the cavern was to house apparatus for detecting solar neutrinos. The experiment ultimately proved successful and earned R. Davis a share of the 2002 Nobel Prize in physics. Recently, a new experiment (LUX=Large Underground Xenon detector for dark matter particles and WIMP's=weakly interacting massive particles) was proposed for the Davis Cavern that required an increase in height of 2.4 m (8 ft). For many years, the Homestake gold mine was the deepest operating mine in North America. Development extended to the 8000 Level (2,438 m). The mine closed in 2003. Pumps were shut off and the water level rose to the 4350 Level, about 150 m (500 ft) above the Davis Cavern. Some six years later after selection for DUSEL proposal development by the National Science Foundation (NSF), access to the 4850 Level and the Davis Cavern was regained. Pumping has lowered the water level to well below the cavern floor. Figure 1 shows the layout and location of the Davis Cavern (Cavity). Detector tank, supporting steel, and so forth were subsequently removed. The cavern was re-supported and new access was developed. By August, 2010, 13,000 ft3 had been removed during enlargement and renovation of the Davis Cavern. Figure 2 shows the detector tank under construction in 1965.

Jan 1, 2012

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By R. Schwarz, E. Pusch, A. Juch

"The paper describes in general the objectives, goals as well as theoretical background of "METSI"-project proposal submitted to German BMBF (Federal Ministry of Education and Research). The METSI project is a starting point for technology and know-how transfer of German water management and water treatment technologies to South African Mining industry. "METSI" is Setswana, one of the eleven official languages in South Africa, and means "water". It stands also for "Management System for the Implementation of Environmentally Sound Water Supply Technologies in South African Mining Areas with Involvement of all Relevant Stakeholders". The project focuses on development, design and implementation of mathematical models that consolidate and evaluate existing data and generate substantiated projections of "water" amount and quality. METSI covers a wide range of scientific, technical, social as well as economic questions related to "water in mining"."

Jan 1, 2011

By John A. Reeves

The unit-train concept of moving raw materials .is considered by many railroad men as the most signifigant contribution to reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling results in the maximum utilization of equipment. For example before the unit train was plaged in servige on coal hauled to one of Mid. Continent's customers, about 900 cars and 9 locomotives were needed to move the coal requirements for this plant, compared with. 250 cars and 6 locomotives used by the present scheduling of unit trains. If the economics of unit-train movements are to be achieved, coal companies no longer can use railroad cars as small storage bins on wheels to accumulate their coal in trainload shipments, but, rather, must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time. In this manner railroad equipment is operated at a high degree of efficiency 'with consequent dollar savings. After negotiations between Mid-Continent, the customers and the Railroad, it was decided a unit train loadout and storage facility at Carbondale was required in order to reduce the delivered price of coal to the customers and thereby contribute to the reduction in the cost of manufacturing steel. Carbondale was selected as the bin site location, because the cost of constructing a railroad to Redstone could not be justified for the tonnages anticipated.

Jan 1, 1969

By David S. Yang, Osamu Taki

The innovative Soil-Cement Mixing Wall Technique, developed independently in Japan, consists of mixing in-place soils with cement grout using multi-axis augers and mixing paddles to construct overlapping soil-cement columns. The applications of overlapped soil-cement columns include cutoff walls for groundwater control and structural diaphragm walls for excavation support. The special features of this technique include water tightness, versatile strength design, and efficient installation in subsurface materials varying from clayey soils to cobbles or soft rocks. Through the introduction of two recent subway projects in Japan, this paper presents the design parameters, construction procedure, quality control and performance of soil-cement wall for excavation support and groundwater control.

Jan 1, 1989

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002

By William C. Cooley

SUMMARY A review is presented of the state of development of high pressure water jet equipment and of large impact hammers for rock tunneling. Information from the U.S.S.R. is based on published literature and three personal visits. Applicable papers which were presented at the International Symposium on Jet Cutting Technology in Coventry, England in April 1972 are reviewed. Data are presented on continuous jet systems, pulsed water cannons, and hydraulic-powered impact hammers with respect to the specific energy of rock breakage and potential application in tunneling machines. INTRODUCTION It has been estimated that the cost of underground excavation during the period 1970-1979 in 15 countries of the Organization for Economic Cooperation and Development will be over $54 billion, an increase of 104% over the period 1960-1969. It is expected that 55% of the tunneling construction will occur in hard rock (Ref. 1). Present tunneling machines are generally limited to soft and medium-hard rock. When used in hard rock, the cost of replacing mechanical cutter bits is high. Therefore there is a need for improved rock fracture methods which can be applied economically in tunneling machines for hard rock. Water jets and mechanical hammers are two

Jan 1, 1997

By V. T. McLemore

Petrographic analysis of rocks is traditionally performed with optical microscopy using thin sections and point counting. However, this does not provide accurate mineral proportions for sedimentary, volcanic, and soil-like material, because rock fragments, groundmass, and matrix are not identified as specific minerals. In addition, groundmass phases in volcanic rocks can be too fine to identify individually, and making thin sections of intact soil-like material is difficult because much of the material is not well cemented. ModAn is a normative calculation that estimates modes ??by applying Gaussian elimination and multiple linear regression techniques to simultaneous mass balance equations? (Paktunc, 2001) and allows location-specific mineral compositions to be used. One of the features of ModAn that makes it appropriate for this study is that it can model one of several sulfide minerals. Mineral compositions for Questa minerals were determined from electron microprobe analysis and entered into ModAn. Then by combining and normalizing results, bulk quantitative mineralogy can be determined using ModAn, petrographic observations, electron microprobe analysis, clay mineral analysis, and the whole-rock chemistry of the sample.

Jan 1, 2009

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

By Matthias Rheinlander

The paper will describe Virtual Design and Construction (VDC) as a tool which will enable us to build a project ?virtually? on a computer before constructing and operating it in the real world. VDC computer models are built, using information from various sources including survey, 3D laser scanning, CAD and GIS to represent the project and its components in a coordinated and consolidated infrastructure model. This model is reviewed and evaluated by, and shared among project teams including owners, con-tractors, designers, engineers, construction managers, stakeholders and operators. It allows teams to fix costly design and construction issues before construction on site. Benefits and lessons learned from global projects will be discussed

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By Leslie F. Ruppert

The US Geological Survey (USGS) is currently conducting a coal resource assessment of the coalbeds and zones that are projected to provide the bulk of the nation’s resources for the next few decades. The Pittsburgh and Upper Freeport coals are the first two beds in the northern and central Appalachian basin region to undergo fully digital coal assessments. The bed-specific assessments are being carried out in partnership with the state geologic surveys of West Virginia, Ohio, Pennsylvania and Maryland. Comprehensive stratigraphic and geochemical databases have been developed for both of the beds. The extent of the bed with mined areas, structure contour, isopach, and overburden thickness maps for the Pittsburgh coal bed have been released as USGS open-file reports.

Jan 1, 1999

By S. C. Chelgani

The Thor lake deposit is a world class resource of rare earth (REE) metals and minerals in Canada. Development work to optimize a REE mineral recovery process flow sheet is underway, however, given the ore mineralogy; the developed reagent scheme is relatively complex. As part of a research project, micro flotation tests were conducted on a feed sample in order to examine factors affecting stream partitioning. SEM-EDX was performed to evaluate variability in grain composition between streams (concentrate and tails) and TOF-SIMS surface analysis was used to determine statistically significant differences in surface species particularly related to potential activation (or depression) of the examined mineral phases. SEM-EDX analysis reveal that the concentrate has a significantly higher proportion of REE bearing grains (carbonates and phosphates) relative to the tail (almost none were identified). Spectral fingerprinting by TOF-SIMS has allowed for the identification of all reagent species investigated. Reagent signal intensity discrimination on test stream mineral surfaces was observed by the TOF-SIMS analysis using reagents at plant concentration levels. TOF-SIMS analysis confirmed that REE bearing grains reporting to the concentrate are doing so in response to collector attachment whereas grains reporting to the tail are doing so in response to a lack of collector and/or in combination with the presence of the depressant. The surface analysis of gangue phases reveal a similar reagent discrimination; the signal intensity of collector species was significantly higher on the concentrate samples relative to the tails while depressant species were significantly enriched on the surface of the gangue phases in the tail samples. A detailed evaluation of the surface species representing the various reagents used in flotation scheme revealed a distinct competitive relationship between two of the reagents. The surface analysis identified that when used in concurrently, there appears to be a negative feedback resulting in a significant reduction in loading for several of the collectors on grains reporting to the concentrate. An evaluation of the effect of reagents on REE mineral in pilot plant is currently under way. Key words: Rare earth minerals, Flotation, Surface chemistry, TOF-SIMS, SEM-EDX

Feb 27, 2013

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.