Search Documents

By John R. Duble

Through 1980, demand for cement in the Pacific Basin countries still seemed to exceed output. Availability of cement in the industrialized and developing countries of East Asia, Southeast Asia, and Australasia for the 1975 - 1980 period are discussed in this report. Quantitative data includes production, imports, exports, and apparent consumption. An account of new cement plants and plant extensions is provided. Countries and areas covered include: East Asia---Japan, South Korea, North Korea, Taiwan, China, Hong Kong, Philippines; South east Asia---Thailand, Vietnam, Singapore, Malaysia, Indonesia; Oceania (Australasia)---Australia, New Zealand, New Caledonia, Fiji.

Jan 1, 1982

By Lu Yang

In the last two decades, acid iron ore pellets have established their predominant position as the iron-bearing burden material for blast furnace ironmaking in North America. It is a general practice that pelletization plants are asked to produce pellets of certain chemical composition and in a narrow range of sizes. A minimum amount of fines created during handling and transportation is desirable. Such a requirement is often expressed indirectly by the minimum compression load causing a pellet to break. The behavior of pellets inside a blast furnace, of course, is very important for a smooth and efficient operation. Before its melting in the lower part of a blast furnace during this period of several hours the behavior of pellets depends on their properties after induration as well as conditions inside each furnace. Among properties of indurated pellets, the ability to maintain their physical integrity in the burden and to be reducible are most important. To maintain the integrity of pellets (i.e., minimal low temperature breakdown, swelling and softening) so that there will be adequate overall permeability for certain wind rate and local permeability for gas/solid contact for reduction. A higher reducibility will moderate the adverse effects of swelling and softening and contribute to a smooth operation and efficient use of heat and reductants in a blast furnace. An article devoted to the relationships between the quality of iron ore pellets and blast furnace practice has been published elsewhere(1); therefore, no further discussion is needed here. The mechanism of strengthening of iron ore pellets during firing has been the subject of investigation of many authors(2). There is no doubt that the bridging of the growing hematite grains, particularly starting with magnetite concentrates, is very significant in the production of strong pellets. Recently, there are many reports from blast furnace operators that they have noticed the adverse effect of LTB in their plants. It is obvious that the strength derived from bridged hematite grains may disappear when hematite is converted to magnetite with thorough breakdown of grain structures. It is suggested that some other strengthening mechanism may be required in order to improve the LTB index of acid pellets. The influence of porosity on both compression strength and reducibility follows regular patterns. It has been suggested(1) that the amount of liquid slag in pellets during firing determines to a large extent the porosity, hence, indirectly, strength and reducibility.

Jan 1, 1983

By D. McElhinney, J. Winfield, G. Buchan, B. Slaker, A. Iannacchione, T. Minoski, G. Rashed, M. Van Dyke, M. Murphy

"The National Institute for Occupational Safety and Health (NIOSH) has previously established pillar design guidelines for the underground stone mining industry. These guidelines were created from an empirical database of pillar observations and were largely drawn from shallow, flat-lying mining operations. Current trends forecast a great amount of underground stone mines developing under deeper cover, higher seam dips, and more frequent multiple-seam mining configurations than in the past. The complex loading conditions and limited experience in these environments presents a substantial increased risk of ground failure. To investigate these loading conditions, NIOSH has installed a pillar and roof monitoring system at an underground limestone mine in central Pennsylvania. The mine is operating in a seam with dips ranging from 13 to 18 degrees and overburdens ranging from 275 m (900 ft) to 425 m (1,400 ft). Instrumentation installed in an undeveloped pillar and in surrounding strata is currently measuring pillar and roof behavior in response to stress redistribution during excavation. Laser scans are being used to measure ground displacement and changes in conditions associated with local mining conditions and significant geological features. Initial stress measurements show a gradual increase in stress in response to mining, and stress changes that correspond with blasts. The seismic system is operational, with calibration events signaling on each of the 18 sensors. INTRODUCTION Improving mine-wide ground control stability can help reduce the potential for catastrophic failure of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted prior research in stone pillar design and has established fundamental pillar design guidelines for the underground stone mining industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2015). The data that constitute the S-Pillar program were derived from past mining experience that was almost exclusively drawn from shallow, flat-lying, single-level mining operations1. Stakeholder interactions with NIOSH researchers have indicated that increased numbers of underground stone operations are expected to mine under significantly deeper cover, with greater seam dips, and under multi-level operating conditions (Slaker and Murphy, 2016). The complex loading conditions and limited experience in these challenging environments present a substantial increased risk of ground failure. Inadequate pillar design in these new and challenging environments could result in catastrophic wide-area pillar collapses and an increased safety burden to miners working in the U.S. limestone mining industry. To develop design guidelines and prevent inadequate pillar designs for these challenging environments, NIOSH is currently conducting detailed pillar response investigations at case-study mine sites operating in challenging environments."

Jan 1, 2018

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By John Jonkman

The cost of equipment maintenance is the largest single expense at many mines and processing plants. It is not unusual for a maintenance and repair budget to be larger than 50% of the punt's total budget. Generally, in the mining industry, 400-60% of the work force in a plant reports to the maintenance department. Studies have shown that many plant maintenance workers are only 33 to 40% productive, working 2.6 to 3.7 hours of every 8-hour day. In recent years, many companies have begun to recognize that- productivity improvements and cost reductions can he achieved by upgrading maintenance methods. This paper discusses ten common causes of low maintenance productivity and how recent advancements in computing technology can be utilized to address these causes for low productivity.

Jan 1, 1986

By P. Samanta, Mohammed N. Azad, Gustad F. Taraporewalla, A. K. Mukherjee, Abhay S. Patra, D. Sachinraj

Beneficiation of coal is a water intensive process, and the water is recovered in downstream operations in the high rate thickener (HRT) and vacuum belt filtration (VBF). Clean coal particles entering the HRT have an inherent tendency to enter the overflow because they are extremely fine and hydrophobic. Hence, flocculants (polymers) are used to floc the ultrafine particles so that they settle and enter the underflow. Ultrafine coal particles (−37 μ), which are highly hydrophobic, if present in the stream, will not be efficiently captured by using flocculants alone. This is observed in the normal plant operation at one of the beneficiation plants in the Jharia region, Jharkhand, India. Approximately 6–7% of the feed to the HRT enters the over flow (supernatant water). Hence, this amount of clean coal particles is not recovered and account for production losses. A comprehensive settling and dewatering test work was conducted with clean coal slurry using several commercially available reagents. Studies were also done on different combinations of reagents, including coagulants and surfactants along with flocculants, to improve the settling behavior of the coal particles. The reagents were assessed based on their performance with respect to settling rates, overflow water clarity, and compaction of the underflow solids. Emphasis was given to the ability of the reagents in compacting thickener underflow to higher densities so that maximum water could be recovered from the thickener. Pretreatment of highly hydrophobic coal slurry with a combination of coagulant and surfactant followed by flocculation showed very good settling characteristics with clear overflow.

Sep 30, 2021

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981

By N-h. Mao

We applied kriging (geostatistics) to interpret the structure of basement rock in Yucca Flat, NTS from borehole data. The estimation error for 118 data is 81 m comparable with those based on both gravity and borehole data. Using digitized topographic data, we tested the kriging results and found that the model validation process (Thomas option) on data gave a fair representation of the overall uncertainty of the kriged values.

Jan 1, 1985

By J. J. Komadina

Since the advent of resin-in-pulp (RIP) technology for treatment of uranium-bearing ores in the 1950?s to current carbon-in-pulp (CIP) processing of gold values, metallurgies and operators alike have wrestled with the problem of interstage screening. Early gold CIP plants such as at Homestake utilized externally mounted vibrating screens in conjunction with air lifts to effect carbon-pulp disengagement. Other operations world-wide have likewise adopted this technique with varying degrees of success. Subsequent development of in-tank launder screens both in South Africa and the United States have been of the air cleaned variety (EPAC)

Jan 1, 1988

By M. K. Boateng, K. Awuah-Offei

"Language barrier in a workplace affects workers’ productivity and safety. The objectives of this paper are to: (1) review the various approaches for breaking language barriers among miners; and (2) analyze the costs and benefits of these approaches, and make recommendations on the way forward. The authors achieve these objectives by reviewing the current approaches in breaking language barriers among miners. The review reveals that some of these approaches can be expensive with less benefits. Thus, it is concluded that mining companies should carefully select the optimal approach to break language barrier. INTRODUCTION Multi-national mining companies have expanded their operations into non-traditional mining destinations to grow and meet market expectations. For instance, Newmont Mining Corporation has about 14 operations and projects located in Africa, Asia, Australia and America (Newmont Mining Corporation Operations and Projects, 2015). Similarly, Freeport-McMoRan operates about 14 mines in North America, South America, Southern Asia, and Africa (Freeport-McMoRan Inc., 2015). Some mining companies have also attracted expatriate workers into their workforce. For example, Ma’aden, the Saudi Arabian mining company, in its 2013 annual report states that 34% of its total employees are expatriates (Ma'aden, 2013). Expatriates constitute a key source of skilled labor and facilitate skill transfer. The success of many international operations relies greatly on expatriate performance (Erbacher, D'Netto & Espana, 2006). Even companies that do not expand their operations into other foreign countries still have to deal with language barriers due to changing language demography of the country and the areas from which labor is sourced. For example, the language composition of the workforce and languages used in South African mines is diverse with miners proficient in Afrikaans, English, Zulu, Xhosa and others to varying degrees (Research Focus (Pty) Ltd, 2011). As a result of these trends, most mines today operate with a multinational workforce. This means cultural differences, including language barriers, exist among the miners. Marschan-Piekkari, Welch and Welch (1999) emphasize the fact that language problems become prominent as companies internationalize and grow their operations into more countries. According to a survey by Forbes, language barrier affects operations. For example, business owners acknowledge that language proficiency may promote a safer work environment (Rubin, 2011). A research has shown that language and cultural barriers in a workplace contributes to reducing workers’ productivity, increasing accidents, and hurts employers’ ability to recruit, hire and retain workers (Morris, 2002). Hence, mines are making efforts to break language barriers in their operating environments. Ma’aden, for instance reported in 2013 that 1,506 of its employees received training in English as a second language (Ma'aden, 2013)."

Jan 1, 2016

By Len H. Steele

To date VMD have designed, built and supplied nine autoclaves to various mining companies in Canada, the US, and Papua New Guinea. Initially, completely fabricated and lead lined units were shipped. The logistics of Placer Dome's Porgera PNG Project necessitated fabricating and lead lining each autoclave in five sections for transportation to site, each piece weighing approximately 30.5 tonnes. Support equipment such as turning rolls, automatic and manual welding machines had to be set up on site to facilitate assembly of these units which was a challenge in planning. This on site erection programme was completed in three months.

Jan 1, 1992

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By Richard F. Hammen

Mineral extraction from sulfide ore deposits usually leads to the combined action of oxygen and water on the newly exposed ore. The result is acid mine drainage, a low pH solution of various metal sulfate salts and sulfuric acid. Paradoxically, the valuable metals dissolved in acid mine water are a liability because they are too toxic for discharge but too dilute to recover economically. The expense of compliance with water quality release standards has reduced the profitability of many mining operations. Solid phase extraction (SPE) columns have been developed to extract metals from acid mine water. These columns are designed to remove the toxic elements from water and recover the metals as purified fractions. This article describes the results of a Phase 1 bench-scale project to test the performance of the SPE columns. The tests were conducted with water collected from the abandoned Berkeley Pit copper mine in Butte, MT.

Jan 1, 1993

By Joseph O. Cook

I know this is, at best, a frustrating period for the coal mining industry. About 20,000 miners have been laid off, mostly in the Appalachian and mid-western areas, and several mines are working less than 5 days a week; however, the industry is experiencing modern growth and, at least, there is the potential for future growth. The coal industry is probably only operating at about 80 percent of its present capacity, and it is certainly capable of helping this country solve its energy problems. Growth, as a rule, does not come easy, and growth in the coal industry is no exception to this rule. Many formidable challenges have to be overcome. As we all know, mining relies very heavily on the earth sciences, which have advanced significantly in the past few years, but we are always working in a changing environment which in most cases is a hostile environment. Large quantities of material are quickly extracted and rapidly moved in, generally speaking, a very confined area. The very nature of the mining business directly and constantly impacts our environment during this period in which the Nation and the world has become increasingly smaller and more concerned about protecting our environment. In addition, growth brings about an expanding work force which is increasingly younger and less experienced.

Jan 1, 1980

By Donald E. Steif

The Tower Mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine, its operation, application, and performance for wet grinding.

Jan 1, 1984

By C. Frenzel

Tunnel boring machines (TBM) utilize disc cutters as the primary means for excavating hard rock. Depending on rock excavatability and rock abrasivity disc cutters can exhibit significant wear. A detailed analysis has been carried out to characterize failure modes and wear patterns of disc cutters. The relationship between rock properties, op-eration of the TBM, and failure modes of cutting tools is clearly high-lighted. On that basis a prediction tool for disc cutter consumption has been developed that allows to estimate not only gross cutter life, but accounts for cutterhead design, premature cutter changes, and disc cutter repair costs.

Jan 1, 2011

By Jerry F. Fountain

Variations in ore grade, mineralogy, and copper pricing structures over the life of the Inspiration mine have mandated many modifications to the treatment methods to maximize process economics. In the 1970's, copper prices generally declined, while inflation, wages, and interest rates increased. A metallurgical treatment route had to be developed for this continuing economic climate which would be capable of minimizing labor, energy, and capital cost requirements. After many years of development, the patented "Ferric Cure" process was introduced to satisfy these requirements. This dump leach process for treatment of mixed oxide/sulfide ore includes: strict mineralogical control of ore placed for leaching, controlled leach pad construction, solution saturation and curing of the pads with higher acid concentrations, and, finally, rinsing of the cured pads for removal of dissolved copper. Leach solutions, high in sulfuric acid during the cure application and low in sulfuric acid during the rinse, contain sufficient ferric iron to enhance the leaching of chalcocitic sulfide minerals.

Jan 1, 1983

By J. L. Roll

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) and the regulations promulgated for that "Act" have resulted in changes to surface mining operations in order to comply with the stringent federally enforced reclamation requirements for prime farmland. In many instances the operator has modified surface mining operations to meet the prime farmland requirements through changes to mining equipment operation, addition of new equipment targeted for reclamation or the use of totally different mining techniques. The major challenge to mine operators has been how to use existing mining equipment to meet the requirements of the "Act." Freeman United Coal Mining Company opened the first new large surface coal mine in Illinois following passage of the "Act." The Industry Mine, located near Macomb, Illinois started mining operations during March of 1982 and was required therefore, to meet all of the requirements of the "Act" including prime farmland restoration. At the Industry Mine a shovel and a cross-pit bucket wheel excavator (wheel) are used for overburden removal and the wheel is addition- ally utilized to assist in reclamation operations. The wheel mines the subsoil thereby elliminating scraper placement of that subsoil and the attendant compaction problems with scraper placed subsoil. The wheel is used to convey topsoil stock- piles from the highwall to the mined overburden in order to lessen scraper traffic and possible compaction on the graded overburden during top- soil removal and replacement. Close control of the operation of the wheel yields more uniform wheel spoil ridges which then require less grading prior to topsoil replacement.

Jan 1, 1986

By W. M. Houston

The phosphate formations of the Pliocene epoch were deposited along the coastal shelf of the eastern seaboard. The deposition of the phosphate is thought to be somewhat contiguous along the early shoreline, and the deposit can be more or less traced over an 800 to 930 mile path from the Florida Gulf Coast, near Ft. Myers, to the Pamlico Sound of North Carolina. This is illustrated in Figure 1. Three areas of commercial importance are currently being exploited from this extensive known deposit: 1 - The so-called ?Bone valley? in Central Florida (multiple operations) 2 - Hamilton County in North Florida (Occidental Corporation operation) 3 - Beaufort County in North Carolina (Texas Gulf Sulphur operation)

Jan 1, 1966