Search Documents

By Peter N. Loncar

Most miners dream of finding a gold mine sometime during their mining careers, but not very often do such dreams come true. On the tenth day of September, 1962, our dream of finding gold came true when the results of the third drill hole were received. This was undoubtedly one of the most exciting days of our lives. Little did we realize then that this was the beginning of a major discovery destined to became one of the largest gold mines in the country. Discovering and mining gold is not entirely new, however, to Eureka. County a old Lynn Mining District in northeastern Nevada. Since 1900 there has been sporadic activity, mostly consisting of small lode mines and placers. These have produced totally about $300,000; and existence of our orebody would probably have remained unknown had it not been for the United States Geological Survey. The USGS extensively mapped the Roberts Mountain Thrust and published a paper indicating that mineral occurred along this fault and in some places was gold bearing. Utilizing this information, our Newmont Exploration geologists located an area in which: drills were brought in to test their theories. By keeping flexible in our thinning and working, we were able to bring a raw prospect to a producing mine with ore reserves of eleven million tons in a short three-year period.

Jan 1, 1965

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

The Golden Grove Project area is located 220 km (137 miles) east of Geraldton in Western Australia (Fig. 1). The project is a joint venture involving Amax Exploration (Australia) Inc. (Amax), Electrolytic Zinc Co. of Australasia Ltd. (EZ), and Esso Exploration & Production Australia Inc. (Esso), each with 31 116% interest, and Aztec Exploration Pty., Ltd. (Aztec), with a 3 1/2% carried and a 3% contributing interest. The venture covers two significant volcanogenic massive sulfide deposits and some 40 km (25 miles) of highly prospective Archean volcanics. During the course of the past 12 years (to 1983), all four companies were responsible for operating the project at one time or another and all influenced the discoveries. The Gossan Hill and Scuddles deposits are typical examples of volcanogenic massive sulfide deposits associated with Archean explosive submarine acid to intermediate volcanic complexes. They are located in the northwesterly trending Yalgoo greenstone belt of the West Australian Archean Shield. Gossan Hill, located in 1972, is essentially a copper deposit with minor zinc lenses; to date, 97 diamond holes have delineated a geological resource* estimated to contain 13 Mt (14.3 million st) of of 3.4% Cu and 13 g/t (0.38 oz per ton) Ag in the main lenses with minor lenses totaling 2 Mt (2.2 million st) of 3.7% Cu and 17 g/t (0.49 oz per ton) Ag and 1.7 Mt (1.9 million st) grading 1.5% Pb, 14% Zn, and 87 g/t (2.8 oz per ton) Ag. Scuddles is a zinc-copper deposit with gold and silver credits. It *Resource estimate provided by Esso for inclusion in Aztec Exploration Pty. Ltd. 1982 Annual Report was discovered in 1979 and, to the end of 198 1, had been delineated with 42 diamond holes. On the basis of this drilling, a geological resource* of 26 Mt (28.7 million st) has been estimated in three coalescing lenses. The lenses comprise 7.5 Mt (8.3 million st) of 2.1 % Cu, 12 g/t (0.35 oz per ton) Ag, and 0.3 g/t (0.009 oz per ton) Au; 7.6 Mt (8.4 million st) of 0.4% Cu, 9.9% Zn, 73 g/t (2.3 oz per ton) Ag, and 0.7 g/t (0.02 oz per ton) Au; and 1 1.0 Mt (1 2.1 mil lion st) of 1.1 % Cu, 9.3% Zn, 8 1 g/t (2.6 oz per ton) Ag, and 1.5 g/t (0.044 oz per ton) Au. Readers are referred to Frater (1978) and Harris et a). (1982) for a more detailed geological account of these deposits.

Jan 1, 1991

By Gino Vogt

In mechanized tunnelling operations, performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequately dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole project. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer’s point of view.

Dec 1, 2022

By Gary W. Hudiburgh

The gangue in some magnetite ore bodies contains feldspar; the alkali content of the feldspar reduces the usefulness of these iron ores. One method of decreasing the feldspar content in magnetite concentrate is froth flotation. The amine flotation of feldspar from magnetite concentrate was investigated using zeta potential measurements, Hallimond tube flotation tests and laboratory-scale flotation tests. The zeta potential of various feldspars (microcline, albite, anorthite, oliqoclase and anorthoclase) were determined as a function of pH; the point of zero charge ranged from pH 1.4 to 2.5. Hallimond tube flotation tests using two amine reagents were conducted on the feldspars. Hallimond tube flotation tests using six amine flotation reagents were performed on the cobber tails (quartz, albite and microcline) from a magnetite concentrating plant; in all cases, over 85 percent flotation recovery was obtained at pH 8 and 10-5 to 10-4 [M] collector addition. Laboratory-scale (667 grams) flotation tests were performed on the magnetite concentrate in an attempt to float the feldspar which had reported to the concentrate. The effects of three different collectors, two levels of collector concentration, three pH levels, starch and HF acid were investigated.

Jan 1, 1975

By E. M. Frizzell

It is unlikely that improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel cost/shortages, and increasing haul distances as in the past. Therefore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this Bureau of Mines contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic, and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data were gathered from extensive literature searches, European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configurations.

Jan 1, 1979

By D. J. Sweet, B. Seymour, T. M. Emery, M. Armatys, J. P. Bourgeois, W. Johnson

The Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) has partnered with a narrow vein, hard rock underground mine to research the effects of the binder content on the elasticity and post-peak ductility of cemented hydraulic backfill (CHB). This is part of a larger study to enhance the long-term integrity of ground support in underground mines. As mining advances deeper and stresses increase, CHB mix designs will benefit if they can be modified to handle higher levels of strain which are induced by an increased stope closure, typically affected by a reduction in stope width and increased mining depth, or through dynamic loading resulting from a local seismic event. This portion of the research examined the impact of reductions in binder and their impact on Young’s modulus, peak strength, and post-peak ductility.

Mar 2, 2022

Software exhibitors at MINExpo will feature the newest, the best, the most comprehensive computer-based tools available to get minerals from the ground to the market. From the ?cloud? to the pit, the variety that will be featured is almost limitless ? a digital tool for every phase of the mining lifecycle. Blue Sky Network SkyRouter brings the Blue Sky Network to the cloud. Using its interactive Web portal, SkyRouter, with detailed mapping and integration with Google Earth, the Blue Sky Network links enterprises to personnel and assets anywhere on earth through Iridium satellites. The cloud-based solution is designed to support connectivity with remotely dispersed mobile assets, including Blue Sky?s dual-mode GSM and Iridium tracking and communications services. This enables seamless connectivity with assets in problematic cellular reception areas, where only 10 percent of the Earth is covered, and in remote locations.

Jan 1, 2012

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By R. W. Plume

Gold extraction along the Carlin trend requires large withdrawals of ground water, which can be perched, unconfined at shallow depth, and (or) confined at depth. Five hydrogeologic units-Quaternary basin-fill sediments, Tertiary basin-fill sediments and sedimentary rocks, Tertiary volcanic rocks, Devonian to Ordovician siltstones, and Devonian to Ordovician carbonate rocks--form the framework for two aquifer systems that discharge along some reaches of the Humboldt River and its tributaries and are recharged by streamflow along other reaches. Ground-water withdrawals eventually could affect these stream-aquifer interactions. Further work is needed to quantify regional hydrologic processes and evaluate potential effects of mining on water resources.

Jan 1, 1992

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By Josef Arnold, Norbert Fuegenschuh

The “Eggequerung” is an important part of the German Railway’s (Deutsche BahnAG) modernized Dortmund—Kassel line. The heart of this 13-km-long (8 miles)construction lot is the double-track Egge Tunnel with a total length of 2,880 m(9,450 ft.). The tunnel was driven using the New Austrian Tunnelling Method (NATM).The construction contract also called for a reinforced concrete secondary lining, guaranteed for a full water pressure of 30 m (100 ft.) water column. Preliminary geological study already showed that very problematic geological-hydrological conditions would have to be expected. This talk describes the chosen NATM driving concept that was adapted to the prevailing geological and hydrological conditions, the special driving method applied in geologically difficult zones as well as the water control concept used during driving. The flexibility and the limits of the NATM under exceptional hydrological conditions are illustrated. Also described are reinforced concrete lining works for the watertight secondary vault (reinforced concrete secondary lining without water-proofing membrane).

Jan 1, 2003

By Kenneth J. Reid, Marian S. Stachowicz

A preliminary evaluation of a new in-stream particle size analyzer has been carried out using materials obtained from a taconite plant in Northern Minnesota. Results are reported for bench scale, pilot scale and full scale tests, the latter being carried out in a taconite plant concentrator. The unit employs a novel scanning laser microscopy principle and details of the equipment configuration and operating principles are presented and discussed. Data acquisition is via an eight channel digital electronic system and particle counts are collected on the basis of reflected light pulse time intervals which are a direct measure of particle size. Output is available as an eight point individual or cumulative size distribution or as computed averages. The practical aspects of sample point location and flow requirements for reproducible results are outlined and discussed.

Jan 1, 1990

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By Gordon A. Gross

Banded siliceous manganese-iron bearing sediments recognized as distinctive facies of Algoma type iron-formation constitute low grade resources of manganese in many countries. Manganiferous facies associated with oxide and carbonate facies of iron-formation have iron to manganese ratios ranging from 0.2 to 2 and commonly about one. Manganiferous facies up to 30 meters thick occurring separately or with other iron-formation facies are associated with cherts, carbonates, shales, turbidites, tuffs and lavas. Primary cherty manganiferous facies and their gondite metamorphic equivalents represent significant manganese resources and are protores for higher grade deposits derived by secondary enrichment processes.

Jan 1, 1982

By A. D. S. Gillies, A. Haghighat

"A study has been undertaken at the Missouri University of Science and Technology (MS&T) limestone Experimental Mine to determine new fans set up and wiring options.to install additional mine ventilation capacity. Selection for main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Available fans for ventilating the mine are Joy and Alphair axial fans each of 24 kW each and two Spendrup booster fans of 12 kW each. The installation of main mine fans on the surface and underground entails numerous considerations. Design of a ventilation network for the Experimental Mine incorporating surface and booster fans has been accomplished using Ventsim Visual program software. The ventilation network has been separated into two segregated parts. A main surface fan and a booster fan have been used in each segregated part of the network. The mine has had a vane axial Joy fan in place for many years. The Alphair 4800 VAX 1800 full blade adjustable pitch vane axial fan was selected and installed as the other surface fan and eventual replacement for the Joy fan. Main surface fans have been connected individually to booster fans in series. The Alphair main surface fan has been installed vertically. Four different wiring options and related cost estimations for addition of the new main fans to the ventilation network have been considered. The analysis resulted in an innovative steel frame design used to allow the fans, when necessary, to be moved to the side of the shaft so that blast pressures do not damage the blades. INTRODUCTION Main fans are the heart of a mine’s ventilation network and play a key role in supplying required airflow (Haghighat, 2014). The Missouri S&T Experimental Mine has been developed in uniform limestone with few stratigraphic features. The mine floor is approximately horizontal and water drains well. A study has been carried out on MS&T Experimental Mine. Selection of main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Ventsim Visual computer simulation has been used to assist in design of the ventilation network. Wiring circuits, fan foundations and flexibility have been considered as the three main parameters for surface fan installation at the Experimental Mine. Two surface and two underground wiring options and three surface set up options and related cost estimates for the new surface fan system were investigated. Frequent use of explosives in the mine occurs throughout each year. Flexibility in changing the position of a surface fan is important. A number of options have been considered for the location of a vertical main fan positioned on the upcasting shaft. The mine is used for a variety of purposes and flexibility has a high priority amongst design considerations."

Jan 1, 2015

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By K. H. McDaniel

Eight Mine Weather Stations (MWS) installed at the Waste Isolation Pilot Plant (WIPP) to monitor the underground ventilation system me helping to simulate real-time ventilation scenarios. Seasonal weather extremes can result in variations of Natural Ventilation Pressure (NVP) which can significantly affect the ventilation system. The eight MWS(s) (which previously collected and stored temperature, barometric pressure and relative humidity data for subsequent NVP calculations) were upgraded to provide continuous real-time data to the site wide Central Monitoring System. This data can now be utilized by the ventilation engineer to create real-time ventilation simulations and trends which assist in the prediction and mitigation of NVP and psychrometric related events.

Jan 1, 1997

By A. B. Cecala

Two recent Bureau studies evaluated workers' dust exposures in automated pallet loading processes. The first study involved a Bureau designed dust control system using a push-pull ventilation technique. The unit was shown to reduce workers' dust exposures by 76% during pallet loading at a ground silica operation. A hydraulic lift table was used to automate the bag stacking process; this kept the loading height constant throughout the entire pallet loading cycle. The second study evaluated different commercial automated pallet loading systems. These systems automatically stack the bags onto pallets, shrink wrap the pallets, and deliver the pallets to a fork lift pickup location. Results from a ground silica evaluation site indicated respirable dust samples taken were below the Threshold Limit Value (TLV) as established by the Mine Safety and Health Administration (MSHA).

Jan 1, 1990