Search Documents

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By David A. Zegeer

It's a pleasure to be here, and an honor to be invited to address this distinguished group of professionals. Today, I'd like to begin with an overview of progress in coal mine safety and health. I'll discuss some current areas of concern. And I'll make some suggestions as to where we may be headed in the future. This year marks the coal industry's 15th anniversary under the Coal Mine Safety and Health Act, which took effect in 1970. We have come a long way in those 15 years. As a coal mining man from way back, I remember the era when the Coal Mine Safety and Health Act first was passed. Some of you may remember it, too. At that time, the safety and health of coal miners was in the public eye even more than it is at present. One reason was a mine explosion that killed 78 miners when it occurred in a large underground coal mine in November 1968. That disaster raised tremendous public concern about protecting the safety of miners.

Jan 1, 1985

By J. R. Riding

In situ solution mining of uranium has environ- mental advantages over conventional mining. The leaching of uranium, however, alters the groundwater quality in the aquifer where the mining occurs. Currently, regulations require that the groundwater be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring groundwater quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By Timothy J. Orr, Jami M. Girard

A NIOSH study on occupational deaths between 1980 and 1989 indicated that in the United States, mining had the highest average annual fatality rate (3 1.9 per 100,000 workers) of any other major industry. Since "lack of training" was often cited as the primary cause of accidents, NIOSH has been investigating new methods for effective training. One such method is the use of low- cost, desktop computers to simulate a virtual mining environment. Computer-based training offers several advantages over conventional training because the computer programs provide a three- dimensional environment that allows the trainee to practice using evacuation routes, encounter mining hazards, and view mining operations without being exposed to any real danger. One major focus of the project is mine escapeway multiuser training using desktop virtual reality programs. Researchers have imported mine maps into the software for the purpose of practicing actual evacuation routes and procedures. Various scenarios for evacuation can be practiced in a three-dimensional computer simulation of the mine in a disaster situation, complete with smoke, fire, and other dangers. Depending on the trainee's job description (i.e., foreman, shift boss, beltman, etc.), certain tasks need to be performed in addition to navigating primary and/or secondary escape routes. Each scenario allows for individual or team-based training and provides a means to educate mine workers in hazard recognition and hazard avoidance. Using this program, mine workers can practice evacuating various mine layouts without the danger and expense associated with escapeway training in an actual underground mine. Each scenario can be changed to test the trainee's reaction in a variety of circumstances and run many times so the trainee can practice concepts. This training experience will help reinforce the knowledge acquired during more conventional classroom instruction, and the inherent flexibility of the program allows training materials to be tailored to meet the specific requirements of individual mines.

Jan 1, 2002

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

By C. Garcia, J. J. Opazo, A. Potulsha, T. Comi

"Sierra Gorda SCM is a joint venture partnership of KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining and Sumitomo Corp. (Japan) operating in northern Chile. The Sierra Gorda openpit mine and coppermolybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, wellinstrumented mine in Chile. This article contains a general review of the project including geology and history.This was a fast-track project going from greenfield site acquisition to mill startup in 10 years. Highly experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied.The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (Fig. 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km (3 miles) from the village of Sierra Gorda at an elevation of approximately 1,700 m (5,600 ft) above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km (37 miles) northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic and Escondida, to name a few.The primary organizational value at Sierra Gorda is "Zero Harm." This includes employees, contractors, the environment, the community, plant facilities and mine equipment. A cornerstone of this program is called 5X5S (five by five S), which combines the lean principles of 5S with the safety model of taking five steps back and thinking about the task at hand for five seconds, five minutes, the time it takes to assess and manage the risk. "People caring about people" promotes proactive engagement in the safety of coworkers and others at work and at home."

Jan 1, 2014

By Bernd Friedrich, Elif Emil‑Kaya, Merve Papakci

In the production of SmCo permanent magnets with excellent temperature stability, corrosion resistance, and oxidation resistance, samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are employed. Cobalt (Co) is a crucial component in tool materials, nickel-based alloys, tablet and smartphone batteries, and electric car batteries. REEs and Co have been listed as critical raw materials by the European Union Commission for many years. Due to the ever-growing demand for Co and REEs in technological applications, the recovery of these elements from secondary sources has garnered significant interest. There are two types of SmCo magnets, one of which contains a high amount of iron, approximately 15.2%. This paper focuses on the recycling of Fe-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Feb 15, 2024

By C. Okrusch, C. Roos, M. Akers, S. Rosenthal

Modern mining consistently faces controversy. Public sentiment impacts the permitting and development of mines, so a quality public relations (PR) program for mining companies may improve society’s impression of the mining industry. Developing mines face more permitting challenges than operating mines, which stems from a lack of societal trust given the history of mining and its impact on the environment. Two case studies were selected based on the type of public controversy they face to demonstrate how pervasive permitting issues are in industry. Both Pebble Mine, owned by Northern Dynasty Minerals (NDM), and Black Butte, owned by Sandfire Resources America Inc (SRA), experienced difficulties with their water permitting due to potential risks their mine developments posed to local fish populations. Pebble has, to date, failed in all of their attempts to become permitted due to concern for the water and the fish. Black Butte dealt with the same problems, on a smaller scale, but was able to become permitted. These two mines will be discussed in detail including local history, mine setting, mining history in America, prevalent culture groups, technology development, and intercultural communication competence (ICC). The mining industry needs to evaluate its ICC skills since ICC directly determines the effectiveness of PR. Based on Barna’s Stumbling Blocks for intercultural communication, methods for improving the mining industry’s PR will be suggested in the hope of easing the permitting process for future mines by developing ICC.

Mar 2, 2022

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

During harsh weather conditions, the presence of fog, dust in the environment degrades the image’s quality, which affects the visibility of drivers of heavy earth-moving machinery in opencast mines. Due to low visibility, mining operations cannot be carried out as drivers are easily prone to accidents. This paper proposes a technique that includes developing a vision enhancement system called perceptive driving assistant system for increasing visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery at opencast mines during harsh weather conditions to overcome the problem. The system consists of high-quality Internet Protocol cameras and thermal cameras for real-time image processing and other well-defined devices, which is quite capable of enhancing the visibility of the image, outlining edges of the road, and detecting obstacles present on the path of operators for smooth driving and reducing threat of accidents. A high-speed graphical processing unit has been used for quality-performance parallel computing, which is well suited for real-time operations to empower fast real-time operations. The calculated frame per second (fps) of image enhancement, object detection, and edge detection is 17.91, 15.91, and 25.09 fps, respectively. The actual frame rate is 26.07 fps, and after applying the algorithm, the final frame rate is 19.65 fps. The calculated accuracy of the object detection model is 81.23%. Field trials indicate that the developed system has performed adequately during foggy weather.

Sep 21, 2022

By A. D. Davis, C. J. Webb

Brohm Mining Company's Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February of 1999 the Governor of South Dakota announced plans to request the U.S. Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable ground-water reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2002

By E. L. Montgomery

Salar basins in the Andean Highlands of Northern Chile contain ground-water resources which could be used to satisfy requirements for the mineral industry in the region. Salars occur in arid zones; average precipitation is about 200 millimeters per year at altitudes of about 4,000 meters, and average annual evaporation is two meters or more. The salar basins are hydrogeologic sinks where water flows from recharge areas at the margins of the basins to discharge areas at the salt encrusted salar at the lowest point of the basin floor. Groundwater circulation occurs principally in the alluvial and fractured bedrock aquifers. Results of pumping tests for exploration and production water wells indicate a range in maximum sustained pumping yield of 62 to 126 liters per second, and where abundantly fractured, ignimbrite comprises the most prolific aquifer. Chemical quality of groundwater is good. Long-term pumping from properly located production wells in the salar basins would result in lowering of groundwater levels and salvage of water in areas where groundwater is lost via evaporation.

Jan 1, 1986

By Ernest M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger mines have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1983

By Brian F. Taylor

The Mexican fluorspar industry is faced with and will face serious problems, some of their own making and others beyond their control. However, they still offer the most secure source of fluorspar for North American' consumers. Since 1975, even in light of declining markets, they have, increased then production capabilities' as shown in Table #1. In analyzing Table #1, we note that Compania Miners Rio Colorado has closed down due to their ore reserves being exhausted. Fluorita de Rio Verde expanded their acid grade fluorspar capacity in anticipation of additional North American business. Campania Miners Las Cuevas presumably increased capacity to meet their North American contractual commitments and to supply their own hydrofluoric acid plant (Fluorex) at Juarez, Mexico. Historically, the Mexican fluorspar industry has relied on the United States as the mainstay for their sales. As shown in Tables #2 and #3, the Mexican share of the United States market has moderately decreased. However, as noted in Table #4 the volume loss is substantial as explained below.

Jan 1, 1985

By M. Peters, P. Schmäh

The development of renewable energies and a sustainable power grid are the challenges for future energy supply. Underground cables will replace the vulnerable overhead lines, because of their safety benefits. Due to the public environmental awareness, smart tunnelling and trenchless solutions are required for inner-city and cross-country installations of underground cables, as well as for crossings and the landfall sections to connect offshore wind farms to the transmission grid. Methods from the tunnelling and pipeline industry provide a high flexibility in the planning of alignments, including versatile tunnel concepts and the installation of protective pipes with E-Power Pipe and Direct Pipe.

Jun 13, 2023

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have ben made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modelling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developped, which can be calibrated far ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables to predict the complete composite particle distribution, and is thus valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1985

By S. K. MONDAL, K. K. K. SINGH, S. Singh, R. K. TIWARY, S. K. Chaulya, G. C. MONDAL, R. S. Singh, T. B. SINGH

In this work, a comprehensive field study was carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling was conducted to envisage dust concentration due to existing and closed mines in the region. The air quality modeling exercise predicted that particulate-matter levels of PM10 and PM2.5 might increase in the ranges of 3.2 to 23.1 and 2.1 to 8.9 μg/m3, respectively, due to mining activities when some of the closed mines will be operated in the region without controlled emission. The predicted total PM10 and PM2.5 at the selected receptor locations were in the ranges of 86.39 to 194.89 and 34.82 to 99.55 μg/m3, respectively. Adequate measures were suggested to control air pollution from mining activities, and an intelligent dry fog system was designed to suppress dust emission efficiently from mineral processing plants and opencast mines. The developed system has special features for facilitating eco-friendly mining.

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Amilton Barbosa Botelho Junior

A new step in the Bayer process has been used to recover NaOH and to reduce its content in red mud. After digestion, the residue is separated from the Bayer liquor and goes through press filters, which enables the recovery of NaOH and decreases the moisture content. It is well known that red mud is one of the most important sources of scandium. For this reason, the goal of this work was to characterize a Brazilian red mud (BRM) for scandium recovery. The sample was collected after the press filter system process. Analysis of energy-dispersive X-ray fluorescence (EDXRF), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), and X-ray diffraction (XRD) was performed. Microwave digestion using an acid mixture was carried out to determine the concentration of the main elements. Fe2O3 represented 40% of the BRM, and the Sc concentration was 43 mg/kg. The SiO2 content was 24%, which is the highest value found in the literature, whereas the sodium concentration was the lowest. A literature review was carried out to compare results with BRM, as well as the current studies for recovery of scandium by the leaching/ion-exchange process. Scandium recovery using a leaching/ion exchange process may be possible with efficiency higher than 90%. The greatest challenge is the occurrence of silica gel formation during leaching.

Oct 19, 2020

By Richard Seal

Nabarlek is situated in the Arnhem Land Aboriginal Reserve about 270 km due east of Darwin in the Northern Territory of Australia. During the dry season (May to November) Nabarlek is accessible from Darwin over the Arnhem Highway-- a distance of 330 km. Throughout the wet season (December to April), except for a few days, access is provided by aircraft from Darwin to the Nabarlek airstrip. Because of the limited access during the wet season, reagents and supplies have to be stock- piled for six months on the site to maintain operations. With the mine and plant being remotely located on private Arnhem land with very limited access outside the site fence, operating personnel are flown to Darwin every six days for their days off.

Jan 1, 1980