Search Documents

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By S. G. Malghan

This paper describes uses of sodium sulfide in the flotation of oxide and sulfide minerals of copper, lead, and zinc. The activation and depression effects of sodium sulfide are of particular importance because of their applications with oxidized lead and copper ores. In spite of its industrial importance; however, the nature of the heterogenious reactions between sulfide ions in solution and the surface of oxidized minerals has not been fully understood. Hence, proposed mechanisms of the sulfide action in flotation, methods of measuring and monitoring of sodium sulfide in flotation pulps, and variables influencing the sulfide addition are analyzed. A review of recent studies shows that sodium sulfide addition to flotation pulps can be monitored and hence the optimum dosage controlled using the platinum and/or sulfide specific ion electrodes. The use of these electrodes for improved reproducibility of bench-scale experimental data and plant implementation of laboratory results is described.

Jan 1, 1985

By Xinghai Lei, Nan Wang, Xiangyang Jin, Yuqi Ren, Yang Li

The upward mining method, as an effective mining method, is widely employed in close-multiple coal seams to extend the service life of coal mines and improve the recovery rate of residual coal resources. However, the upward mining feasibility of the upper coal seam is related to the height of caved zone of interlayer strata after lower coal seam extraction. Therefore, it is extremely important to determine the height of the caved zone after the lower coal seam. The No. 9 coal seam (upper coal seam) and the No. 12- 1 coal seam (lower coal seam) in the Qianjiaying coal mine are selected as the research object. The characteristics of the interlayer strata structure field, fracture field, and subsidence field are studied using UDEC numerical modeling, in which the height of the caved zone is gotten after the No. 12- 1 coal seam extraction. Furthermore, the height of the caved zone is verified by onsite detection of GPR and BTVI. In the numerical modeling, the height of the caved zone is 19.6 m. And the height of caved zone is 14.7 m and 15.4–21.2 m, respectively, by using the onsite detection of GPR and BTVI. The heights of the caved zone onsite detection results are consistent with the numerical modeling result. The No. 9 coal seam is always located above the caved zone after the No. 12- 1 coal seam extraction. Consequently, the upward mining of the No. 9 coal seam is feasible.

Jun 28, 2023

By A. A. Schweizer

This paper documents the growth and projects the future of Green Diamond Sand Products. Since1954, Green Diamond, located in Riddle, Oregon, has been producing sand from granulated nickel slag for use in various markets. Through the years, the company has seen several changes from its ownership to its product lines. In 1991, Green Diamond was producing abrasive sand at a rate of about 30,000 tons per year. It was at this time that Green Diamond became part of Glenbrook Nickel Company. Over the next eight years, Green Diamond would quadruple its production to over 140,000 tons while moving into three new markets, as well. Green Diamond is now producing sand for use in the abrasive, foundry, construction, and roofing industries. In 1998, Green Diamond again found itself under new, private ownership. With plans on developing agricultural sand and spent abrasives recycling, the future of Green Diamond appears to be one of further expansion coupled with diversification of its product lines.

Jan 1, 2000

By X. X. Jiang

An efficient recovery of finely divided magnetite particles of 400/500 mesh from a mixture of magnetite/silica particles has been investigated by imposing a delicate balance between centrifugal and surface tensional forces on these particles. The effect of centrifugal force, surface tensional force, density and size of particles on the overall metallurgical efficiency has been examined. A mathematical model based on a momentum balance on the particles at the liquid/liquid interface has been developed. The validity and limitations of the model are discussed in view of the experimental results obtained.

Jan 1, 1992

By Justin Srednicki, Chenming Zhou

Ambient electromagnetic (EM) noise (natural or manmade) is a major limiting factor for the design and operation of many electronic devices, including through-the-earth (TTE) communications and tracking systems. Extensive studies on EM noise were conducted by the US Bureau of Mines in the 1970s and 1980s. Changes in the design and operation of electrical equipment since then, however, have resulted in changes in the EM noise environment. This paper reviews past research on surveying EM noise in the extremely low-frequency (ELF) and very-low-frequency (VLF) bands, which are the operating bands for TTE systems, and introduces a new battery-powered, rugged, portable measurement system for surveying EM noise in mining environments. Examples of surveyed EM noise measurement results in and above an active underground coal mine, using the new system, are presented in terms of absolute magnetic field strength levels. A new metric, average noise level (ANL), is introduced to characterize the noise level relative to a particular frequency band for a specific location. It is found that EM noise in mining environments varies significantly with time and location. EM noise levels at frequencies of 30 Hz that shifted from power harmonics (e.g., 90, 150, 210, 270 Hz) are relatively low and their variation with time can be statistically modeled by a Gaussian distribution. The conclusions and findings presented in this paper can help better design and operate TTE communications and tracking systems in underground mines.

Oct 14, 2022

By Justin Reed, Sara Bewley, Dwight M. Kinnes, Maryam Sadeghi, Ed Hart

This study compares wet gravity and dry magnetic separation for preconcentrating an allanite-rich rare earth ore from the Halleck Creek deposit. Material in the –300/+86 μm size range was treated to define a flowsheet that maximizes total rare earth oxide (TREO) recovery. The ore is dominated by feldspar and quartz, with hastingsite, an iron-bearing aluminosilicate. Because hastingsite’s density and magnetic response closely match allanite, it is difficult to reject using conventional methods. Two separation approaches were evaluated: MG12 spirals for gravity concentration and an Induced Roll Magnetic Separator (IRMS) for dry magnetic upgrading. MG12 spirals performed well in the rougher stage but provided limited gains when used as cleaners. When IRMS was applied as the cleaner stage, TREO grade and recovery improved substantially, showing that a dry magnetic cleaner circuit can effectively replace the wet gravity cleaner step. MG12 spirals remain suitable for highcapacity rougher duty, but dry magnetic separation delivers higher selectivity, simpler operation, and eliminates water use—offering a more efficient and sustainable preconcentration route in water-constrained environments.

Feb 22, 2026

By Georgi N. Shoushoulov, Ventsislav D. Bozhilov

The mining conditions in the Meden Rid mine at levels below 1000 m from the Earth's surface are specific and rather severe. The rock temperature is about 40-45°C. The air humidity in the workings is approx. 80-90%. There is a limited capacity for additional fresh air supply. The air supply and distribution systems in the mine are very complicated. The airflow recirculation is due to the existing arrangement of the main fans. Certain accidental phenomena are difficult to predict. All these conditions create possibilities for heat and mass exchange between the rock and the air current thus hampering the control of the ventilation and air-conditioning in the mine workings. The changes in the temperature and humidity in certain characteristic places of the development and extraction workings are predicted. The refrigeration output required and the arrangement of the air coolers are also determined. A new ventilation and air- conditioning scherne has been developed. The new ventilation- cooling designs for levels between 1000-1200 m beneath the Earth's surface are based on the use of portable refrigerating machines having low water flowrate as well as heat-insulating and waterproof materials and methods for preliminary cooling of the orebody within the mining block.

Jan 1, 1997

Silver bearing bulk sulfide concentrates from several Peruvian mines were autoclaved in a 19 liter (five gallon) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates following a hot lime jarosite destruction step extracted over 98 percent of the silver and over 95 percent of the gold. Autoclave operating parameters such as time, temperature, pulp density and autoclaved solids recycle were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving, and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to pro-vide reliable scale up data for a 50 -100 ton per day facility.

Jan 1, 1992

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By Nikhil Dhawan, Shrey Agrawal

Feldspar, a low-alumina, and abundantly available aluminosilicate source, is explored in this study to extract aluminum and potassium values. The sample comprises lamellar layers of microcline and albite with quartz containing 17.4% Al2O3, 9.67% K2O, and 66.3% SiO2. Mechanical (milling) and thermal (alkali and acid baking) activation are investigated, followed by HCl leaching. The milling treatment up to 6 h is inefficient in phase dissociation and results in ~ 40% Al and K dissolution. The alkali thermal treatment yielded 80% Al and 71% K extraction. Direct precipitation of the dissolved Al and Si values yielded alumina purity of ~ 29%, and silica gelation separated SiO2 and improved alumina product (94% purity, 71% recovery). Acid baking yielded 98% pure alumina precipitate; however, Al and K extraction were limited to ~ 45% and 65%, respectively. The microwave-assisted alkali treatment was optimal with 800 W and 10 min processing conditions yielding 80% Al and 71% K recovery with 2.26 kWh/kg alumina of thermal energy consumption. The final product contains γ-alumina with a specific surface area of 87 m2/ g. Keywords Feldspar · Alumina · Potassium ·

May 18, 2022

By Monserrat Rebolledo, John L. Uhrie, Candice Simms

Jetti Resources has developed a catalyst which overcomes the passivation of primary sulfides, enhancing the heap leach recovery of copper from chalcopyrite. It is important to emphasize that heap leaching of copper sulfides, whether with or without the Jetti catalyst, is a biooxidative process. We have demonstrated the efficacy of Jetti’s technology in bioreactors, with a chalcopyrite-dominant porphyry ore. In the presence of Jetti’s technology, optimal bioleaching conditions significantly increase copper extraction by 2.6 times that of the baseline.

Feb 1, 2025

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By G. Hoffmeyer, I. Ream

"Several copper projects exclusively utilizing in-situ recovery methods are currently under development in Arizona. Favorable conditions for In-Situ Copper Recovery (ISCR) include a saturated orebody, fracture hosted mineralization, hydraulic conductivity sufficient to effectively inject and recover solutions using wells, and a relatively flat background hydraulic gradient. Safe operation of an ISCR project requires that the operator have the ability to induce and maintain localized hydraulic gradients, thereby controlling the movement of injected and recovered solutions. Benefits of ISCR include reduced initial capital, and a greatly reduced environmental footprint. THE ISCR METHOD EXPLAINED The method chosen to extract a mineral from a deposit is driven by characteristics such as its size, grade and depth of burial. Large lower grade deposits that require significant excavation to access using surface methods are potential candidates for in-situ recovery. ISCR may also be ideal for smaller deposits due to the lower initial capital. However, regardless of the size of the deposit, certain hydrogeologic conditions must be present for ISCR to be successful. In-situ recovery methods do not require excavations of rock from the surface or underground, resulting in a dramatic reduction in surface disturbance when compared to conventional mining. With the ISCR method, what is visible above ground is the processing plant, well heads, piping, process solution impoundments and evaporation ponds. There are no waste rock piles, tailings impoundments, leach pads, or impacts associated with blasting and hauling. Other benefits include reduced initial capital, reduced dust and noise, and lower water use. Early testing of the in-situ copper recovery method by Occidental on the Van Dyke deposit east of Phoenix and by Kennecott at Safford Arizona in the 1970s produced encouraging results, but the permitting regime for a large-scale operation was not yet in place. Additional testing and commercial application of in-situ copper recovery techniques have expanded since the 1980s, most commonly in conjunction with open pit or underground mining operations. For example, several operations in Arizona (San Manuel, Miami East and Tohono) have used in-situ techniques to extract additional copper following conventional mining from parts of the deposits adjacent to open pits or underground workings. Where the rock has been broken up by conventional methods, the method is called “in-place” leaching. The US government has also been involved in assessing in-situ techniques. For example, joint research was conducted by the US Bureau of Mines and industry on the Santa Cruz deposit in Arizona; and both federal and state agencies have been involved to establish the comprehensive permitting regime that exists today. Currently there are several projects in Arizona being evaluated as stand-alone ISCR operations."

Jan 1, 2016

By M. Hancer, J. D. Miller

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCl. Precipitationof the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

By M. S. Enders

The McDonald deposit is a volcanic-hosted epithermal gold resource that is estimated to contain 251,000 kg of gold in 375 Mt of ore at an average grade of 0.7 g/t gold. Phelps Dodge exploration geologists, working for the Seven-Up Pete Joint Venture, discovered the deposit in 1989. By the end of 1992, 494 drill holes for over 113,000 m of drilling, bulk sampling, soil geochemistry, geophysics, metallurgical testing, engineering, and environmental studies had been completed to support feasibility studies. The discovery of McDonald required vision, persistence, and commitment of everyone from the geologist on the drill rig to the senior management of the company.

Jan 1, 1995

By Edwin B. Wilson

The purpose of the panel&apos;s examination of coal mining research and development is to explore how the various groups that make up this research community might work together more efficiently and be more productive. The community, as defined here, includes federal and state governments, coal producers, manufacturers, unions, universities, and industry sponsored research organizations. The framework chosen for these discussions consists of brief presentations by the panel members on their views of the proper role and function of the group they represent. The panel members were also asked to highlight the economic, technical and institutional constraints that affect the performance of research and development and the use of the results. Following these presentations, a number of prepared questions will be discussed by the panel, and audience participation is invited. These questions were given several weeks ago to the panel members for their study. Before proceeding with the panel member reports, a brief review of the importance of R&D to the coal mining industry would be helpful to setting the stage for a constructive dialogue. It is appropriate to begin this review by mentioning that there is complete agreement among the research community that the major goals are: Improve health and safety Protect the environment Increase capital and labor productivity Increase resource recovery Since the basic functions of the academic, industrial and government sectors are different, we should expect that the research and development objectives and priorities, roles and responsibilities under each major goal will be different for each research group. The differences do not represent problem areas. However, problems will arise if the objectives are not properly interfaced at the appropriate time. The consequences of railing to understand the need for integrated programs will be the classic result, best described by the phrase --"a technical success but a commercial failure."

Jan 1, 1978

By Douglas G. Fox

Outputs from industrial activities planned in the Riley Ridge natural gas project are modeled to determine the potential locations of air pollution impacts on the Bridger and Fitzpatrick Wildernesses in Wyoming. The nature of modeling, especially with regard to its realism, is discussed. Alpine lakes which, along with their watersheds, have minimal buffering capacity are being studied because of their sensitivity to acidic deposition from proposed new air pollution sources. A hypothesis which relates a source&apos;s emissions to deposition and lake chemistry in a worst-case sense is presented. Research designed to test the hypothesis and reduce uncertainties is outlined and progress reviewed. Focus is placed on the meteorological transport and atmospheric deposition parameterization contained in the hypothesis.

Jan 1, 1984

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification (nickel, cobalt, copper, and manganese) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte, ammoniacal leaching (gas reduction or Cuprion), and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stems from the 1970s and 1980s and is not always easily accessible. This paper will detail the series of tests conducted and provide updated results obtained (high Ni/Co/Cu recovery with limited Mn/Fe), as well as comment on the potential treatment options on the product solution and residue.

Feb 1, 2025