Search Documents

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By D. W. Alexander

In 1993, CONSOL began investigating new methods of permanently filling coal mine shafts, which after ventilation is stopped, may contain a potentially hazardous atmosphere. Fill materials such as fly ash/cement can be pumped, are non-combustible and non-incendiary but tend to flow into the mine entries. A non-flowable mixture has been developed that minimizes the volume of fill used. The paper presents our recent shaft filling experience including fly ash material properties, mix designs, field problems, placement success, and gas testing techniques.

Jan 1, 1996

By P. J. Arps

Cyanide (CN) is used to recover gold from its ores in many locations worldwide. In spite of the established history of gold mining in Alaska, modern cyanidation methods have been used at only one location, the Ryan Lode Mine at Ester Dome, near Fairbanks. Ore was processed by heap leaching between 1987 and 1989, when permitting issues caused operations to be terminated. Those issues have since been resolved, and plans to reopen the mine are currently being discussed. Plans are also proceeding to develop several other ore deposits in the state, all of which include the use of cyanide for gold recovery [6]. Since tailings and effluent water produced from these mines will require treatment, it is important to develop detoxification methods suitable for the Arctic and sub-Arctic conditions found in Alaska. Several methods exist for removing cyanide from mining wastewater. However, most industrial users prefer chemical treatment systems, and typically use sodium hypochlorite, hydrogen peroxide, or sulfur dioxide/air/copper to oxidize free and complexed cyanides [9]. Biological treatment has been used successfully at two sites in the United States [30,32] and field tested at several others [20,27,28]. In addition, one mine uses "natural processes", which include natural oxidation, photodegradation, and degradation by naturally occurring bacteria [33].

Jan 1, 1994

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez, Nishan Pokhrel, Lizeth Jaramillo

This paper presents a case study of respirable dust characterization in a thin-seam coal mine in southern West Virginia. Samples were collected in various locations within the mine and analyzed using scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), thermogravimetric analysis (TGA), and Fourier transform-infrared (FT-IR) spectroscopy. The study found high non-carbonate mineral content, particularly aluminosilicates and silica, in the dust. The results indicate that fine aluminosilicate particles may interfere with SEM-EDX analysis, leading to an underestimation of coal content. The findings highlight the importance of using multiple analytical methods to accurately characterize respirable coal mine dust.

May 5, 2022

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

By Jiang Shuguang, Zhang Huicheng, Wang Xingshen

Based on the experience about determination of properties of the main fan in mine shaft, this paper relates at length how to reasonablly select test system, test methods and test instruments, how to appraise the reliability of determination results, and how to effectively control the adjusted air etc. The merits and demerits of the two methods of determining air with Nine- Anemometer and Pitot meter are compared.

Jan 1, 1991

By R. Lawrence

Mineral property valuations to be used for Canadian securities regulatory purposes must comply with CIMVal1. The technical basis for a CIMVal report is the same as that required for a technical report that complies with NI 43-1012. NI 43-101 describes the content to be covered in a technical report, while also covering other requirements, one of which is that the report should be based on a property visit. CIMVal is based on five tenets that the valuator must follow: ? Materiality. ? Independence. ? Transparency. ? Competence. ? Reasonableness. Upon its adoption by CIM Council in 2003, it was hoped that the new CIMVal code would be adopted without change by the several Canadian regulators.

Jan 1, 2011

By R. C. Burtan

Long before the dawn of recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It has been well established that prehistoric man discovered flint. "The Flintstones" were aptly named. The flintknappers of southern England and Wales still exist today in ever dwindling numbers as they seek out chunks of flint. It is a well known fact that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica containing materials have a great many uses in modern society. However, this material is potentially extremely hazardous to our health. Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. It is obvious to us that he was describing silicosis. It is also apparent from ancient writings, that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century, B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. It was certainly described by Agricola in his "De Re Metallica" published in 1556, in which he described lung disease among hard rock miners. This publication, I'm sure, is of special interest and perhaps known to many of you in the mining community. The original document was written in Latin and was translated in 1912 by two gentlemen, Hoover and Hoover. One of these translators was Herbert L. Hoover, a former president of the United States, who made his living before his presidency as a mining engineer.

Jan 1, 1984

What is the preferred electrolytic cell design and why? Hall: Considerable research remains to be done on electrolytic cell design. Studies are presently being conducted to determine optimum voltage and amperage. Zadra cells, which were used in some of the first carbon plants, are efficient when properly installed. Gold and silver are deposited on large-capacity, cylindrical steel wool cathodes. At times high value sludge falls from the cathode to the bottom of the cell. Rectangular cells, which were developed at some smaller operations in Nevada, require less floor space and have some desirable features in that cathodes can be moved and sludge can be removed from cell bottoms without actually shutting down the circuit. In South Africa two types of cells using graphite and diaphragm configurations are being tested. Duncan: The rectangular cell has one problem it's easy for shortcircuiting to occur. If you don't have a good seal on the side of the tank and on the bottom, the solution is going to want to flow around the bottom and sides of the cathodes and you're going to get poor performance in the cell. That is the advantage the Zadra cell has over the rectangular cell. With good sealing, which is a must, you should be able to get a ratio of the value of the solution going in to the value of the solution coming out of 10 to 1. Ken, can you tell me what you're attaining on the Zadra? Hall: At the Homestake gold operation in Lead, the cathode in the No. 1 electrowinning cell is loaded to about 600 ounces when it is moved to the refinery. At this time the No. 2 cathode is moved to the No. 1 cell. The No. 3 cathode is moved to the No. 2 cell and a cathode with new steel wool is placed in the No. 3 cell. In rectangular cells this sometimes is not possible because the loading on the cathode in the last cell may be as high as that in the No. 1 cell. As Don has pointed out this can probably be prevented by good seal design between cathodes. Potter: At the risk of sounding as though I'm straddling the fence, I really believe that either the round cell, as developed by Jack Zadra, or the rectangular cell will do an acceptable job. The Zadra is a fine unit. Leaks are not unknown but there are not very many. However, the rectangular cell is very saving of floor space. Plastics have been greatly improved during the past year or two and there is a very efficient design for the rectangular cell. It would have six cathodes in it and contain about 25 ft of steel wool. The body of this rectangular cell would be reinforced fiberglass plastic but with an integral lining of a high temperature plastic. I think either cell is so efficient and reliable that I would almost be tempted to flip a coin depending on floor space requirements. Either cell can be used to pull a loaded cathode and to advance the lesser loaded cathodes. Don, what is the configuration of your cell? Duncan: The Pinson rectangular cell has dimensions 2 ft wide, 30 in deep, and 10 ft long-long enough to take a dozen cathodes and anodes. We are currently using six of each but are not up to full capacity as yet. It's a steel tank coated with rubber. We have copper bus bars, which brings to mind that the last cathode in the tank, in one instance, was loaded heavier than the first one. That was probably a function of poor contact between cathodes and the bus bar. You can have erosion of the bus bar and if you don't get current flowing into the anode and out of the cathode, the cells will not function properly. Kappes: Just a few comments on cell design. In an alcohol stripping circuit we are running in Beatty„ NV, we are using PVC pipes for all circuitry piping and a commercial polypropylene electrolytic cell. They seem to be working quite nicely. The cell itself has eight cathodes measuring 18 in2. At six gallons per minute flow into the cell, at an average gold content of about 500 ppm, we seem to get good loading on the first three to four cathodes and not much on the end cathodes. At 12 gallons a minute flow we seem to be seeing gold uniformly along all eight cathodes. We are running at quite a high amperage level, about 400 amps into that cell. Gene McClelland, US Bureau of Mines, Reno Research Center (from the floor): I was associated with a company where the packing density of their steel wool cathodes was much too high and created some short-circuiting problems in their electrowinning circuit. I would like to ask the panel if they can recommend a packing density for cathodes in pounds of steel wool per cubic foot. Hall: The weight of steel wool put on one of our cathodes is 10 lb and the dimensions of the cathode are such that density would be about 0.75 lb/ft3. Duncan: I made a rough calculation and I'm estimating about 2 lb/ft3. Potter: In checking over a number of electrowinning operations, I found apparently very satisfactory operation within the limits that have been mentioned. I have come to a figure of about 0.5-1.0 lb of medium grade steel wool per cubic foot packed as uniformly as possible, of course. One consideration in packing is the fact that there should be good contact between the steel wool and the conductor. Operators tend to compact the steel wool more than would be desirable just to try to maintain good contact.

Jan 10, 1981

By Alfred W. Eustes III

The first of a series on the evaluation of rock cutting tools, this paper discusses the results of full-scale laboratory drilling tests that compare the performances of several polycrystalline diamond cutter (PDC) coring bits. The tests were performed in welded tuff as part of a site characterization program. Number of cutters, size of cutters, air course design, and other parameters were evaluated as they affect penetration rate, but this paper focuses mainly on the relationships of torque vs. thrust (weight-on-bit), specific energy vs. penetration rate, and thrust vs. penetration rate. These relationships change in diagnostic ways according to bit type, bit condition, and type of welded tuff.

Jan 1, 1998

By C. Athanassopoulos

Geomembranes have been used in the mining industry since the early 1970s in solution and evaporation ponds, tailings impoundments, and heap leach pads. Traditionally, heap leach pad lining systems have consisted of a single geomembrane liner placed directly over a prepared subgrade of locally available soil. Heap fills are constructed by placing a layer of highly-permeable drainage stone (overliner) over the geomembrane. Crushed ore is then placed on the leach pad in 3- to 10-m (15- to 30-foot) thick lifts, sometimes reaching final heights of several hundred feet. The crushed ore is irrigated with a chemical solution which dissolves the precious metals from the ore. The nature of the chemical leaching solution depends on the metal being targeted. Low pH sulfuric acid solutions are generally used to leach copper and nickel; high pH cyanide solutions are used to leach gold and silver. The metal-laden pregnant leach solution (PLS) passes down through the ore pile and is captured in a drainage system. Metals are extracted from the leach solution and the solution is then recycled back onto the leach pile. When under load, geomembranes are vulnerable to damage from large stones both in the soil subgrade and in the overlying drainage layer. Although intact geomembranes are virtually impermeable, installed geomembranes will have a small number of holes due to imperfect seams or damage during construction and filling operations. These holes serve as open pathways for leakage into the soil below. Smith and Welkner (1995) estimated liner leakage rates ranging from 5 to 10,000 L/ha/day, depending on the type of heap pad liner and level of construction quality assurance (CQA). Thiel and Smith (2003) reported liner leakage rates up to 2,000 L/ha/day for a valley fill facility with heads ranging from 15 to 35 m.

Jan 1, 2011

By John Reilly

The author?s paper at RETC 2007, ?Alternative Contracting Methods? addressed strengths and weaknesses of DBB+DB and introduced Construction Manager/General Contractor (Portland model) and Alliancing (Australian model). Considerable interest in these was expressed by several public agencies at that Conference and at the presentation. The author is assisting the Washington State Department of Transportation (WSDOT) and the Toronto Waterfront Revitalization Corporation (TWRC) with possible implementation of Alliancing. WSDOT is evaluating ways to do this and is considering a delivery methodology, under existing Legislation, based on the CMGC Portland model with incentives and disincentives, moving towards Alliancing. This paper will build on the 2007 paper and update implementation considerations.

Jan 1, 2008

By Henry E. Reed

This presentation is about a small company, Industrial Mineral Products, that was formed in 1972 with one product and one customer and by a series of value-added changes avoided disaster and increased sales many times over. The principal of the company stopped by my office in Seattle looking for industrial mineral opportunities in the Northwest. We got together and went through all the minerals in Ladoo's "Industrial Minerals" from Abrasives to Zircon to see if we could find something available on the vast holdings of the Burlington Northern. At that time one of our lessees was operating a silica sand mine near Ravensdale, Washington and indicated that he might be interested in selling out. This sounded interesting to my client and within two weeks the transaction was completed.

Jan 1, 1990

By Gary P. Thomason

We have all heard a great deal about how various projects were financed or certain companies were successful in obtaining a bank loan. There are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of sources available to finance minerals operations, but let me assure you that these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to almost all minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. In the following pages I hope to provide some insight into what I define as the loan approval process. Having pre-offered my definition, I intend to delineate the various stages of the process and the planning and information I believe should be contained in each. My ultimate goal is to help you think like a banker and, in so doing, stay on top of the process so that you can successfully obtain the funding necessary for your projects.

Jan 1, 1983

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By R. L. Hudak, R. F. Randolph, A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. The National Institute of Occupational Safety and Health (NIOSH) has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by nine decibels. The “Inquiring Ears Want to Know” fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By J. Paraszczak

Underground metal mining involves many challenges. Economic slowdown, tough international competition and sometimes volatile metal prices put constant pressure on mine operators to increase productivity and to reduce production cost. At the same time, countries such as Canada, the United States and Australia are experiencing skilled labor shortages that might even stall development of certain mine projects. Furthermore, some stages of underground production take place in particularly hazardous environments where the safety and health of miners is at risk. Automation of some processes in underground mining is one of the promising avenues to alleviate some of these problems. Loading and haulage are among the most critical operations and areas where implementation of autonomous vehicles has been targeted. However, although health and safety issues are a primary driver to opt for automation, the latter should ensure an acceptable level of productivity and pro?tability. With this in mind, this article focuses on the factors affecting operational effectiveness of autonomous underground loading and haulage equipment and the means to maximize it.