Search Documents

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By M. K. McCarter

Surface mining applies to extraction of mineral resources from water and sediments of rivers, lakes, seas, and oceans; from solutions circulating through broken rock and soil; and from rock and soil excavated from the earth. Surface mining is responsible for the majority of mineral production in the United States and a substantial portion of the world?s total production. This section deals specifically with extraction methods which employ mechanical processes in a relatively dry environment to free minerals from the earth. The following section, Section 15, deals exclusively with aqueous methods. With recognition of the importance of reclamation in all activities which temporarily disturb the earth?s ecosystems, it is appropriate to classify mechanical extraction methods as either deferred reclamation or concurrent reclamation. Deferred reclamation is necessary when the shape and logistics of the excavation require that it remain open throughout the productive life of he project. Upon exhaustion of economic reserves, the opening is then reclaimed in a manner consistent with public safety, environmental acceptability, and land use policy. Methods employing deferred reclamation are commonly referred to as open pit or quarry mining. Metallic ores, industrial minerals, and coal are all extracted using open pit methods. Typical examples are provided in Chapter 14.1.

Jan 1, 2008

By Robert W. Row

Advanced physical coal cleaning processes that are now under development may remove significantly greater fractions of pyritic sulfur and ash than do commercial coal cleaning processes at comparable heating value recoveries. These processes may be useful for reducing sulfur dioxide emissions from electric utilities and other emission sources. However, little work has been done to determine their applicability to any major coal market. The northeastern states of the United States are interested in burning more coal, but with further sulfur dioxide emission restrictions. Their nearest coal sources are relatively high sulfur Northern Appalachian coals. The project discussed in this paper, which is scheduled to be completed in June 1985, has the objective of technically and economically evaluating various coal supply scenarios involving five selected advanced physical coal cleaning processes; and comparing the economics of them with alternative fuel supply options open to the northeastern users.

Jan 1, 1985

By R. V. Stewart

This chrysotile asbestos orebody is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 mi) north of Montreal; 480 km (300 mi) north of the tree line and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1/4 mi) in length some 61 m (200 ft) in width and plunges at 25-30 below surface to a vertical depth of at least 610 m (2000 ft). The orebody was originally evaluated by programs of surface mapping, diamond drilling and bulk sampling. The fibre is semi-crude, possesses excellent strength, and good fibre length distribution.

Jan 1, 1978

By Martin B. Zimmerman

It is becoming evident that traditional methods of econometric analysis are inadequate in estimating-the long-run supply of minerals. Econometrics is limited to extracting estimates from observations of the theory predicts that the least cost deposits will be exploited first.1 The estimation of parameters from past data then must lead to biased projections of the future. Mining conditions in the future will be worse than in the past and it is the impact of the future conditions on cost that we need to know. In this paper we present a methodology for dealing with this problem. We estimate a "cumulative cost" function that yields the long-run marginal cost of mining as a function of cumulative output produced over time.2 This is relatively easy to do for coal mining in the United States where exploration for new deposits is not a major factor in supply. The first step of the procedure relates cost to the rate of output and to the geological conditions of the mine. The second step combines geological information on remaining deposits with the cost function to yield the cumulative cost function. A central theme of both these steps is the interaction of economics with geology. The best deposits are selected first and in each step of the estimation allowance must be made for this fact. The problem of depletion is part of the general problem of structural change. The change through depletion in the nature of the exploitable mineral stock is only one factor that calls for an analysis sensitive to the changing circumstances of the industry. The factors impinging most heavily on the coal industry today are the strict environmental regulations legislated

Jan 1, 1977

By Kurt M. Larson

Future haulage cost projections led Foster Yeoman Limited into developing a fully mobile crushing and conveying system at its Torr Works quarry in Somerset, England. The purpose-built system has an effective throughput of 2,500 tonnes/hour and features an Orenstein and Koppel (O & K) manufactured walking frame, a Fuller-Traylor type 54 X 74 TC gyratory crusher, and unique mobile conveyor modules designed and manufactured by Foster Yeoman. Used in a single-bench operation in this 6 million-tonne per annum limestone aggregate quarry, the system is fed at the production face by 2 Caterpillar 992C loading shovels. The entire system is moved on a daily basis following production face locations.

Jan 1, 1986

By G. P. White, J. M. Jones

Computer simtiation is a technique that has beers around for many years. Its applications include designing steel mills, planning space shota, or even developing ways to beat the casinos in Las Vegas. However, the use of computer sirndation in surface coal mining is fairly recent. To promote its use, several government agencies, including the US Bureau of Mines, Forest Service, and Department of Energy, contracted with universities and private companies to develop computer simulation programs for surface coal mining. Some of these developers include McDonnell-Douglas Electronics Co., Pennsylvania State University, Montana State University, Fluor Mining and

Jan 9, 1984

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By Patrick Linzer, Lindsay Linzer

By its nature, seismology has been a data intensive field since the first digital computers were introduced in the 1950s. The first empirical models were developed in the same period and are still widely used today, for instance, the Gutenberg-Richter frequency-magnitude relationship (Gutenberg and Richter, 1956). Machine learning (ML) methods make it possible to redefine these empirical models using large datasets and examining considerably more parameters, where their significance to the problem being addressed is methodically and repeatably evaluated using robust statistical methods. In this paper we develop a simple logistic model for the short-term prediction of seismic events above a threshold magnitude from a mine’s event catalogue comprising more than a million events with 14 basic parameters from which a pool of over 830 derived parameters was developed, covering a series of 11 precursory time windows. The logistic model was fitted stepwise using SAS with α = 0.025 for both entry and acceptance. 25 variables from the pool met the acceptance criterion. The findings were surprising in that parameters a rock engineer or seismologist might have expected to be the most significant in the logistic model were not; instead, it was an increase in standard deviation of the immediately-prior seismic magnitudes that carried the most weight, followed by the average maximum source displacement and median apparent volume change. These findings make intuitive sense because the increasing scatter of the magnitude shows an increasing number of large events being recorded that could be indicative of instability in the system that could lead to large events. The model is rudimentary and enormous scope exists for more exploration in terms of data pre-processing, model types, and response variable definitions.

Apr 26, 2022

By E. Shelobolina, S. M. Pickering, J. E. Kogel

A long history of weathering and bacterial alteration processes have transformed Georgia’s Coastal Plain kaolins from dark organic muds to recrystallized white pigment-grade industrial clays. A sequence of six stages in development of these valuable mineral deposits is outlined over their Late Cretaceous and Tertiary deposition and alteration history. Anaerobic and aerobic iron oxidizing and iron-reducing bacteria are present in the Georgia kaolins. These bacteria may have had a major role in iron and organic matter removal during several of the alteration stages that occurred over the past 60+ million years. Iron was likely solubilized by both iron-reducing and iron-oxidizing bacteria, depending on availability of Fe(II), Fe(III), and NO3. Thus, over long periods bacterial activity slowly led to nearly complete groundwater removal of iron from the kaolin deposits. Further bacterial iron removal on an industrial process scale may eventually prove feasible. “Without the multitude of living reactions as channels for energy and electrons and without the enormous capability of life to transfer with and against chemical gradients, there would be practically no or at least a very reduced geochemical rock cycle on this planet.” (Krumbein and Dyer, 1985, p. 157)

Jan 1, 2002

By M. Hodgson

The redox reactions that occur on pyrrhotite and pentlandite in contact with oxygenated deionized water were examined using voltammetry. Reactions were put forward in which both minerals were progressively hydroxylated to form thermodynamically metastable surface intermediate products. These intermediates were modelled as metal deficient sulphides where a sulphurous layer was coordinated onto the remaining metal sites via polysulphides. Prior to hydroxylation pentlandite exhibited changes in the surface stoichiometry which were not related to pH effects. The formation of polysuiphide-sulphur intermediates were believed to promote collectorless; flotability for the two minerals. Microflotation tests (0.3 g samples) verified that the surface potential and particle size affected the flotation response, excessive oxidation inhibiting the minerals' flotability. Larger scale tests using ore samples (30 g) confirmed that the extent of pulp oxidation, particle size distribution and the presence of frothers affected the flotation response, the findings being in accordance with the postulated model for the hydrophobic species generated on the pentlandite and pyrrhotite surfaces.

Jan 1, 1985

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968

By A. C. Bigley

Before going into this subject, I would very much like to call to your attention some past history on patents granted by the United States Patent office that involved ammonium nitrate. On February 10, 1885, a patent was granted to Russell S. Penniman. "The object of this invention is to securely protect ammonium nitrate against deliquescent and to maintain it in substantially its normal disintegrated condition, so as to afford a new product suited for ready use in the manufacture of high explosives, and enable the immediate admixture thereof with any of the well known explosive substances or compounds heretofore employed. 'Whether the nitrate be thus granulated or otherwise reduced to a granular or divided condition, it is then thoroughly mixed with about twelve (12) percent of the fluid or semi-fluid carbonaceous protecting medium, which forms a readily applied jacket or coating for the granules of nitrate and also serves as a carbonaceous element in such explosive compounds as it may thereafter be employed in."

Jan 1, 1958

By W. D. Hausel

Archean supracrustal rocks of the South Pass greenstone belt of western Wyoming have been the State's most prolific source of gold and iron ore. Actual gold production statistics are incomplete, but as much as 400 to 500 thousand ounces may have been mined with some silver and tungsten as a by-product. Iron ore was also mined from the greenstone belt for 22 years, and production totaled more than 90 million tons. Immediately south of the exposed greenstone belt in the Oregon Buttes area, Tertiary boulder conglomerate, which has been eroded from the granite-greenstone terrain, may contain a gold resource of 28.5 million ounces (Love and others, 1978). The amount of gold placered from stream alluvium derived from these Tertiary conglomerates is unknown.

Jan 1, 1986

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By R. D. Lawrence

Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of general accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.

Jan 1, 2000

By G. Watson, S. Sawyer

A Method to Calculate Hydrodynamic Loads on Underground Bulkheads Bulkheads are structures built in openings in underground mines to impound water, preventing the water from entering the active mine workings. These structures not only have to be designed to withstand the static, hydraulic pressure, but also the dynamic or seismic pressure, which would be generated by an earthquake. Bulkheads can be considered underground dams. Unlike dams on the surface, bulkheads are often subjected to hydraulic heads that exceed the heights of the bulkheads. Theodor von Karman in 1933, and Westergaard earlier, developed the equation by which the hydrodynamic pressures on surface dams could be calculated. Civil engineering handbooks of today contain this equation. In this paper, using the methodology developed by von Karman and Westergaard, the authors have developed an equation by which the hydrodynamic forces on bulkheads could be calculated when the hydraulic head exceeds the height of the bulkhead.

Jan 1, 2007

By Erica Frederickson

"Millennials. Doesn’t the word just make your blood boil? You’ve probably encountered one of those kids who think they know best despite a lack of any real experience.Hi, my name is Erica, and I am a Millennial. We often get a bad rap, sometimes for good reason. But we do have qualities that are often overlooked. For example, I am happy to share with my generation a real desire to make a difference in the world and a commitment to innovation. Does this mean I think we always have good ideas? No – especially not right away. After all, few of us came anywhere near a piece of construction equipment until arriving for our first job, as was the case for me. We may have fancy degrees, but not many of us learned to run a jackleg drill in school.Two weeks after graduating college in 2011, I packed up my bags and moved to New York City to work as a field engineer for Traylor Bros. Inc. on the Queens Bored Tunnels project (Granite/Traylor /Frontier Kemper, JV), part of NYC MTA’s multi-billion dollar Long Island Railroad East Side Access project. It was here I became acquainted with the notorious New York City union workers. Perhaps the greatest challenge of my career thus far was earning the respect of the field supervision and craft workers on this first project.The first time I asked a maintenance mechanic to clean a piece of equipment in accordance with our maintenance protocol I got a flat-out “No.” It was the most powerless I had ever felt. But why should these experienced workers trust a 21-year-old girl with her civil engineering degree and no prior experience? I realized no employee on the job had any reason to listen to me — not until I proved my worth. Fortunately, I arrived on the job site just as we were commissioning the slurry plant for the first tunnel drive. I dove into learning as much about the slurry tunneling process as possible and was able to quickly pick up the ins and outs of running the slurry separation plant. As none of the other engineers or management had first-hand experience on a slurry tunneling job, I soon became the go-to engineer in the slurry plant. No one questioned me if I asked to have something done around the plant after that, or if they did, they quickly learned that I had a convincing answer as to the need for the task. I was even able to play a large role in shaping our slurry monitoring and control methodology."

Jan 1, 2015

By Richard M. Winar

In September of 1988, the United States Environmental Protection Agency (US EPA) published final regulations that effect owners and operators of underground storage tanks (USTs). These regulation include stringent technical requirements for owners and operators of USTs containing petroleum and certain hazardous substances. The technical requirements effect both new (those installed after December 1988) and existing USTs and include notification; performance and operating standards; release detection, reporting, investigation; release response and corrective action; and closure requirements for out-of-service USTs. The USEPA also published final regulations regarding financial responsibility requirements for owners or operators of petroleum USTs in October of 1988. These regulations require owners or operators of petroleum USTs to demonstrate financial responsibility for the costs of corrective action and compensating third parties for bodily injury or property damage caused by releases from petroleum USTs. Like thousands of other industries, the mining industry must become thoroughly familiar with these new regulations in order to properly manage their UST systems, ensure compliance, and understand other ramifications imposed by these regulations.

Jan 1, 1990

By Christopher Nelsen, Daniel Dobbels, R. Zachary Hollenbeck

Recent major floods have inundated Historic Ellicott City, Maryland, resulting in loss of life and property damage. Howard County, Maryland, has developed the Ellicott City Safe and Sound Plan to mitigate the risk of flash flooding in the Historic District, including a proposed stormwater conveyance tunnel. Challenges to overcome include thick zones of saprolite along the alignment, multiple near-surface structures, and minimal rock cover under an active railroad, while minimizing impacts to the public and historic structures. The project will also pursue recognition through the ISI Envision verification process.

Dec 1, 2022