Search Documents

By K. Park

Coupled influence of sulphidizers and xanthates on the electrokinetic property and flotation behavior of malachite was systematically examined via electrophoretic mobility measurements and microflotation tests. The electrophoretic mobility results for the malachite before and after surface modification with different types (Na2S and (NH4)2S) and amounts (1×10-7?1×10-4 moles/g) of sulphidizers, showed that the isoelectric points (IEP) of malachite differed at the low dosage level depending on the type of the sulphidizer, which ranged between 5 and 9.5. However, the IEP values were observed to be shifted from high to low pH values with increasing amount of sulphidizers and finally ranged between 3 and 4, indicating that the sulphidizers played a different role on changing the surface property of malachite. In order to further understand the effect of sulphidizers on the electrokinetic property and flotation behavior of malachite in a sulphidizer+xanthate system, flotation tests were carried out with malachite sulphidized with Na2S and (NH4)2S (adsorptive amount=8×10-5 moles/g) at different bulk xanthate concentrations. The results showed that the flotability of (NH4)2S-treated malachite was greater than Na2S-treated one over the entire xanthate concentration investigated, indicating that the type of sulphidizers played important role in malachite flotation; however, no obvious correlation between electrokinetic property and flotability of malachite was observed.

Feb 27, 2013

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By D. W. Olson

The estimated value of natural gemstones produced from U.S. deposits during 2004 was $12.9 million. This was a 3-percent increase from that of 2003. U.S. gemstone production included agates, amber, beryl, coral, garnet, jade, jasper, opal, pearl, quartz, sapphire, shell, topaz, tourmaline, turquoise and other gem materials. More than 60 varieties of gemstones have been produced commercially from U.S. mines. But commercial mining of gemstones has never been extensively undertaken in the United States. Most of the deposits have been relatively small compared with other mining operations. In the United States, much of the current gemstone mining is conducted by collectors, gem clubs and hobbyists rather than business organizations.

Jan 1, 2005

By K. N. Han, N. S. Kim, H. Yoon, J. S. Sohn

The leaching behavior of silver and silver oxides in ammonical solutions has been studied. The current study is concerned with an effective recovery of silver from secondary sources such as spent silver batteries. Silver associated with these batteries appears in various forms including metallic silver, argentous oxide, Ag2O and argentic oxide, AgO. The leaching behavior of metallic silver in ammoniacal solution has been studied using an electrochemical mehtod. Oxidants used in this study include hyperchlorite, hydrogen peroxide, bromine and iodine. Results on cyclic polarization and Tafel plots on the silver anode in ammoniacal solutions are presented and the results are discussed. The dissolution rate of metallic silver in ammoniacal solutions is also compared with those of silver oxides.

Jan 1, 2002

By Kenneth J. Hartman

Introduction The term kaolin is derived from kauling, a Chinese word meaning high ridge. This was the name of a hill in China where kaolin was first mined several hundred years ago (Murray, 1976). Other common names used for kaolin include clay and China Clay. Clay technically has a broader meaning and could refer to bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin. But it could also be due to a significant historical use in ceramic applications. The terms kaolin and clay will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's wide-spread industrial usages center on kaolinite's physical features of good color, low viscosity, and inertness. Kaolin is described as a hydrous aluminum silicate with an approximate composition of 2H2O • A12O3 . 2SiO2. A new version of the product is calcined clay with modified hydration content. It is gaining widespread use. Components of any particular kaolin, in addition to alumina and silica, are viewed as impurities. The more values deposits and, hence, higher priced kaolin products are those of the highest purity. Kaolin is the most widely used mineral in paper manufacturing throughout the world. Key production centers are located in England and the US. Most of the Tatter's production is located in Georgia. The key markets for Georgia kaolin are paper markets - both paper coating and paper filling. These paper markets extend throughout the world, not just to domestic markets. In fact, export markets are second in size only to domestic paper markets for Georgia's producers of kaolin. Just as the paper markets are important for kaolin producers, kaolin is an important raw material for papermakers. Compared to the other three major pigments - titanium dioxide, calcium carbonate, and talc - kaolin's 1984 tonnage for papermaking represented 85% of the total. Even though titanium dioxide's unit value is much higher, kaolin's estimated total 1984 value still represented 51% of total dollars spent by papermakers for the four pigments. Kaolin grades- are briefly defined using particle size and brightness as principal means of classification. Likewise, grades of papers using kaolin are defined using the American Paper Institute's guidelines. From these definitions, associated kaolin grades used in particular grades of paper are reviewed. Special emphasis is placed on how qualities desired in certain papers are achieved through the use of specialized kaolin grades. World kaolin production World production statistics (Coope, 1979; Table 1) demonstrate that kaolin is produced in many areas of the world. About 60% of production is centered in the US and England (Fig. 1). Deleting Eastern Europe's produc-

Jan 4, 1987

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By J. Winterton

Estimating the residual metal inventory of large heap leaching operations is desirable for many reasons. Several methods have been tried with limited success. Drilling data from the Valley Leach Facility at AngloGold Ashanti's Cripple Creek and Victor Gold Mine has been used to develop a robust inventory estimation technique. The technique is presented along with discussion of the particular inventory components and evaluation methodologies.

Feb 27, 2013

By J. A. Ober

China, Mexico, Spain and Turkey are the leading producers of celestite (strontium sulfate), the most common strontium mineral. Of an estimated 510 kt (562,000 st) of celestite produced worldwide during 2004, 98 percent was produced in those countries. Deposits of strontianite (strontium carbonate), another strontium mineral, have been identified in China and Malawi. Relatively small quantities are reported from the deposit in China. Although celestite deposits occur in the United States, no domestic celestite has been mined since 1959.

Jan 1, 2005

By Leonel Lopez

Throughout Mexican history, mining has been an important, traditional activity. Before the "Discovery of America," native miners worked a variety of deposits throughout the country, including Mixtec gold and gem mines in Oaxaca State and Aztec gold, silver and copper from mines in Michoacán. The 500th anniversary of Mining in Mexico after the "Discovery of America" was initiated by the Mexican mining sector on April 15, 1991. As early as 1548, when the Guanajuato mining district was discovered, Mexico had become a leading world producer of precious metals. Since then, Mexican mineral production has developed in cycles, responding to changing technological, economic and political conditions. During the 20th century, Mexican mine output reached its peak in the decades of the 1930s and 1940s, when it was producing about 40% of the world's silver, 15% of its lead, 10% of its zinc, 4% of its copper and 3.5% of its gold. In 1990, by way of contrast, these percentages of world output stood at 13.5% for silver, 4.7% for lead, 4.1% for zinc, 3.2% for copper, and 0.43% for gold. The lowest production levels were recorded during the 1960s and 1970s, when Mexicanization of the industry and increasing state controls weakened mineral economics to a point that mineral exploration budgets were sharply reduced or eliminated, along with the industry's future. Only the noble old mining districts continued to supply production, with occasional eruptions of "bonanzas" and new extensions in established mining districts.

Jan 1, 1994

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the Cost Approach category for Real Property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves, and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties.

Jan 1, 2011

By J. S. Y. Wang, R. C. Trautz

A 9-meter-long drift was constructed in the unsaturated-fractured tuff at Yucca Mountain to evaluate the potential for water seeping into an underground opening. Forty seepage tests were performed by releasing a finite volume of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations, and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2000

By Ian Farmer, Nigel Glossop, Philip Garritty

Performance of tunnel boring machines - usually expressed in terms of penetration per revolution - is determined by relations between machine thrust and torque, head diameter and rock strength. It can be shown that for a given machine power and head diameter there is only one rock strength at which the machine performs optimally. In weaker rocks the available torque limits performance and in stronger rocks, the available thrust. Performance data shows that, historically, machines have been designed to cut weaker rocks. Optimization of thrust is required to improve performance in stronger rocks.

Jan 1, 1987

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By Lynn B. Hales

There is a large economic opportunity associated with improving metallurgical performance in mineral processing plants that use process control. Thus, future control systems will be developed towards more sophisticated user friendly, computer-based systems that use powerful software analysis and control techniques. Auto-tuning, adaptive control and process models will gain expanded use because of their transparent availability to the system designer. Control of individual unit operations will be optimized and coordinated through expert systems that monitor economic conditions and management directives and direct operations accordingly. Plant areas, once considered cost centers, will be integrated into plant-wide control systems for economic control and optimization. This article looks at new control hardware, process sensors, control strategies and software development tools. It also looks at the economics driving the continued development of advanced process control systems. Process control systems routinely used in the mining industry were born when the microprocessor was invented. They have continued along an evolutionary path from vendor specific processing hardware and proprietary operating systems to computer industry standard "open architecture" systems. The many economic forces that drive the development and functionality of these process control systems will cause this evolutionary process to continue. Two of the broadest categories are the needs of the end users and the desire of the system manufacturers to distinguish their products from one another. More

Jan 1, 1994

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By M. A. Islam, H. Mischo, G. Barakos

Among the thirty-five declared critical raw materials (CRM) in the United States, there is no sustainable domestic production for the fourteen of them, while for some others domestic supply does not meet the national demand. Numerous potential critical raw material projects are in advanced exploration stages. However, the price uncertainties for many of these commodities put feasible future production into question and come into contrast with overly optimistic price forecasts published in all feasibility studies related to such exploration projects. Thus, in this work, a newly developed smart computational tool is used to evaluate the real perspectives of several CRM exploration projects implementing actual commodity prices, and to conduct reverse calculations in order to find the prices at which each project can be viable.

Mar 2, 2022

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994