Search Documents

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By D. Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 “Welded Steel Conveyor Pulleys” adequately defines standard pulleys for most aggregate material handling applications. However, many aggregate applications demand pulleys of higher capacity and reliability than that offered by CEMA pulleys. This paper examines the CEMA Pulley Standard and pulley specifications for aggregate applications requiring greater capacity and reliability than the CEMA Pulley Standard. Higher reliability increases the uptime and has a lower total cost of ownership.

Jan 1, 2003

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By I. J. Duckworth

Due to improved, stringent safety regulations, many modern road tunnels are statistically safer, per kilometer, than above ground roadways. However, the public perception and reaction in the event of a serious tunnel fire is very different to that associated with a surface incident. Vehicle fires in road and rail tunnels are recognized to represent an immediate and extreme danger to the patrons of those systems. Unlike workers in the mining and civil construction industries, the general public are neither trained nor equipped to fight fires or evacuate under deteriorating smoke conditions. Accordingly, for the majority of modern transportation tunnels the ventilation infrastructure is sized on the requirement to control the combustion products from worst-case fire scenarios and to provide a tenable evacuation route for the tunnel users. It is common for these same emergency ventilation systems to be employed, often in a reduced capacity, for other operating modes such as the dilution of pollutants during congested traffic conditions. This is one of the fundamental differences to mine ventilation, where primary ventilation systems are not typically sized based on fire scenarios. This paper presents an overview of the subject of fires in vehicular tunnels. This includes a brief history of major transportation tunnel fires followed by a discussion on the resulting legislation and standards that govern the design and operation of tunnel emergency ventilation systems. A summary is provided on the common criteria, theory, and design techniques that are employed during tunnel emergency ventilation systems design. Information is provided on fire detection and suppression, with a discussion on the growing acceptance of wet suppression as a means to mitigate major fires in road tunnels worldwide.

Jan 1, 2009

Every two years, industry leaders and practitioners of tunneling and underground construction gather at the Rapid Excavation and Tunneling Conference (RETC) to learn from their peers about the most recent advances and breakthroughs in this unique fleld. Industry experts from around the world highlight their most recent projects and share real-world experiences. They also share with their colleagues new technologies and methodologies that attendees can take home to their respective projects. The 2013 RETC was held June 23-26 in Washing-ton, D.C., itself home to several major tunneling and underground construction projects. The conference is sponsored by SME. Attendance was 1,384 professionals. The accompanying exhibit hosted 159 companies in 188 booths. A few of the topics covered in the technical sessions dealt with caverns and large spans, contracting practices, tunnel linings, design and planning, geotechnical considerations and instrumentation. The conference was preceded by four short courses, all well attended. They were ?Grouting in Underground Construction,? ?Tunnel Lining Design,? ?Microtunneling Application? and ?Risk, Uncertainty and Hard Decisions.? In addition, a sold-out field trip to D.C. Water?s Blue Plains Tunnel took place following the conference. The Blue Plains Tunnel is part of the agency?s Clean Rivers Project. Also during the meeting, three students each received $5,000 scholarships from the UCA of SME, while another three students each received $2,500 scholarships from RETC (See page 53).

Sep 1, 2013

By William R. Yernberg

The early part of the decade was marked by world-wide problems and economic difficulties. In 1980, President Jimmy Carter ordered the failed military mission to rescue hostages in the U.S. Embassy in Iran, Mt. Saint Helens, WA erupted killing 60 people and the Soviets and Mujaheddin guerrillas clashed in Afghanistan after the Soviet invasion. Later in the year, Ronald Reagan was elected president, defeating Carter. The first launch of a space shuttle (Columbia) occurred in 1981. Also in 1981, the first IBM-PC’s begin to roll off the lines. In 1982, Argentina invaded the Falkland Islands and Mexico’s economy was in collapse. In 1980, the U.S. unemployment rate stood at 7.1 percent, and by 1982 the rate increased to 9.7 percent. 1980 marked SME’s first full year in its new office building in Littleton, CO. The new facility was dedicated in November 1979. Claude L. Crowley was executive director of SME in 1980 and remained in that position throughout the decade. SME’s membership stood at about 26,000 throughout this period (1980-1982).

Jan 1, 2007

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By T. Johnson

Mining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel, cobalt and uranium have been particularly active. The world?s largest nickel mine ? the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale?s Voisey Bay mine in Labrador. Voisey?s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $1.4 Billion Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 ? 250,000 MT/yr manganese carbonate.

Feb 27, 2013

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

Jan 1, 2001

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Gary Tomaino, Specialty Minerals Inc., is the chair of the SME industrial minerals technical committees. Technical committee vice chairs include: •Lucy McCartan, U.S. Geological Survey, agricultural minerals as well as sorbents, filter and process aids. •Steve Herron, Oglebay Norton Performance Minerals, ceramics and refractory materials. •Srinivas Veeramasuneni, U.S. Gypsum, chemical raw materials. •William Langer, U.S. Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2003

Beneath some of New York?s most iconic buildings ? The Met Life Building, the Helmsley Building, the Waldorf Astoria ? crews are busily at work on the Metropolitan Transportation Authority?s long-awaited East Side Access (ESA) project. In fact, it is 14 floors beneath the famed Grand Central Station where one of the centerpieces of the project, the new Long Island Railroad (LIRR) station terminal, is being blasted and carved into shape. When completed in 2016, the $7.3-billion ESA project will increase LIRR?s capacity into Manhattan and significantly relieve congestion at Penn Station. Currently, 37 LIRR trains per rush hour roll into the crowded Penn Station where many riders must then transfer to subway trains to complete their commute. When completed, the ESA tunnels will bring an estimated 160,000 riders directly to Grand Central Station, saving those riders 30 to 40 minutes. Studies have found that more people work within walking distance of Grand Central than Penn Station. ?The benefits of the project are tremendous,? MTA Capital Construction President Michael Horodniceanu told more than 340 industry professionals attending the UCA of SME?s George A. Fox Conference in New York on Jan. 26. ?The ESA is the first expansion of the LIRR in 100 years. It will increase the East River tunnel capacity by 50 percent and will help support job growth around Grand Central.?

Jan 3, 2010

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By T. Hudaverdi

Several studies have been conducted on blastability and prediction of fragmentation. The term blastability is used to refer the susceptibility of the rock to blasting and is closely related to fragmentation. Parameters that determine fragmentation by blasting may be divided into two groups. The first group consists of blasting design parameters. The blast design parameters are controllable parameters and determined by the explosive engineers. The burden, spacing between holes, bench height, drillhole diameter, stemming height and explosive density are all design parameters. The second group consists of rock mass parameters that are referred to as uncontrollable parameters. The uncontrollable parameters are physical and mechanical properties of rock and rock mass structure. The strength, modulus of elasticity, density of rock, number of joint sets, joint orientation and joint spacing are among uncontrollable parameters. The rock mass parameters and blast design parameters should be considered together to explain fragmentation process. In this study, a blast database was accumulated to use for multivariate analysis. The blast database contains the blasts performed near Istanbul region quarries and the blasts that were preformed in various mines in the world by the blasting researchers. The cluster analysis was used to separate the blast data into different similarity groups. Group memberships were analyzed and checked by the discriminant analysis. Then, the multivariate regression analysis was used to develop a prediction equation for blast fragmentation for each group. Finally, a validation of the suggested models was performed for various mines. The model comprises blast design parameters, mechanical properties of rock and rock mass structure.

Jan 1, 2011