Search Documents

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Openpit mining (prestripping) began in 2010 and full production commenced during 2011. The openpit mines feed both a sulfide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp Inc. Peñasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals.As a consequence of lower grade ores expected with advancing mine life, Peñasquito is facing a declining metal production profile. To maximize returns and asset value, plant modifications, including the addition of a carbon prefloat circuit and a pyrite leach circuit to improve recovery, are currently being undertaken. This carbon prefloat circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Peñasquito operation. The addition of the carbon prefloat circuit was also a key driver in allowing the Chile Colorado openpit to be developed.These conditions alongside Goldcorp’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this article and include improvements in geomodeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 7, 2018

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By Terry M. Tilley, Gregory P. Sherry

Purpose This is a unique project because the mining and tunneling industries have become highly mechanized and cannot normally accommodate a project where surface disturbance must be minimized or eliminated when there is less than 10 feet of ground cover. More traditional less mechanized methods must be employed and the skills and techniques for accomplishing the work have become all but non-existent. Therefore, this article highlights those areas of specialized skills and techniques. Methods The article will describe the design approach, the method(s) of ground support selected, the method(s) of excavation selected, the planning, scheduling and materials selection process. In addition, the article will describe the actual production characteristics and the results of the project. This approach will concentrate on productivities, adaptations to actual conditions and the quality of the end product. The design approach basically was to insure that the temporary support methods were adequate for the excavation and shoring stage of the project. The final concrete liner was designed using conventional structural design methods with the goal of constructing a tunnel that will last 100 years. The methods of support were spiling and variations of spiling in order to provide advance temporary ground support. In this project spiling is steel channel cantilevered and driven into the ground ahead of the working tunnel face which supports the ground allowing the face muck to be removed with overhead protection’. Conclusion This will be a discussion of the applicability of the methods. The actual performance of the excavation and shoring methods will also be evaluated. The final concrete liner completion results, the actual production rates and the conformance with budget and schedule will be addressed.

Jan 1, 2005

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

This study was conducted to establish the effects of a diesel particulate filter (DPF) system with sintered metal substrate on the concentrations and size distributions of nano and ultrafine aerosols and concentrations of nitric oxides in underground mine air. The study focused on the formation and transformation of nucleation mode particles in mine air under prevailing test conditions. Experimental work was conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of control technologies directly in underground conditions. The DPF system was examined for four repeatable steady-state engine modes using a naturally aspirated mechanically controlled Isuzu C240 diesel engine fueled with ultralow sulfur fuel. The engine coupled to an eddy-current dynamometer was operated in the underground drift with tightly controlled ventilation. Measurements upwind and downwind of the exhaust system discharge were used to quantify the effects of the DPF system on the mine air. A baseline was established using a standard muffler. The study showed that sintered metal DPF systems reduced the total mass of aerosols in the mine air by more than ten-fold when compared to a muffler. The nucleation mode aerosols (50dem<40 nm) in mine air were found to be strongly influenced by engine operating mode. The concentration of nucleation mode aerosols was found to be significantly higher for high-load modes than for low-load modes. The muffler and DPF system resulted in comparable total nitrogen oxides (NOx) concentrations. However, the nitrogen dioxide (NO2) fraction of the total NOx was found to be substantially higher for both systems for low-load modes than for high-load modes.

Jan 1, 2009

By James N. White

Completion of the Hall Street Coal Transfer Terminal in St. Louis marks the beginning of a major shift in the movement of coal to the power generating stations of the Midwest and South Central regions of the United States. The location of the terminal is significant. The 10 million ton- per-year facility is the first high capacity rail-to-barge transfer terminal to be built on the western shore of the Mississippi. This terminal and others to follow will link the massive coal fields of the West with the high coal consuming markets adjacent to the 25,000-mile Inland Waterway System.

Jan 1, 1979

Semisoluble salt minerals are characterized by their ionic bonding and are distinguished from soluble salt minerals by their limited solubility in water. One group of semisoluble salt minerals being considered is the alkaline earth salt minerals, including fluorite (CaF2), calcite (CaCO3) and apatite (Ca5F (PO4)3), as well as celestite (SrSO4) and barite (BaSO4). Another group of semisoluble salt minerals being considered is the rare-earth salts, which include bastnaesite ((Ce, La) CO3F), monazite (CePO4) and xenotime (YPO4). Surface chemistry features of these selected semisoluble salt minerals are discussed with respect to flotation separations. First, the surface chemistry features of alkaline earth semisoluble salt minerals are reviewed, and then the surface chemistry features of rare-earth semisoluble salt minerals are examined. The discussion includes electrokinetic behavior, wetting characteristics and collector adsorption.

By I. Tsolas

This paper presents the use of non-parametric approach (i.e., data envelopment analysis, DEA) for the development of environmental sustainability indicators in mineral processing using environmental, economic and/or integrated indicators (i.e., indicators that interrelate two dimensions of sustainability). A case study based on real publicly available data is presented to illustrate how the proposed approach can be implemented in practice. The merit of this approach, which is based on the productive efficiency framework, is that it provides environmental sustainability indicators that can be used internally for benchmarking purposes and externally for sustainability reporting.

Jan 1, 2008

By Marcelo de Oliveira, Antoine Allanore, Dennis P. Chen, Davide Ciceri

Potassium fertilizers (potash) are mined in a handful of countries in the Northern Hemisphere. Potash is either expensive or unavailable to the farmers of the Southern Hemisphere. Alkaline alteration of K-feldspar rock (ultrapotassic syenite) in autoclave in the presence of Ca2+ generates a mixture of K-bearing calcium-aluminum-silicate-hydrate (C-A-S-H) minerals that potentially can be used as an alternative local fertilizer. This work investigates the effect of processing temperature (200 °C, 220 °C, and 230 °C) and time (from 0.5 to 3.0 h) on pH, mineralogy, and elemental availability of the C-A-S-H mineral mixture. Increasing temperature results in an increased conversion of K-feldspar and increased content of both the mineral tobermorite (Ca5Si6O16(OH)2·4H2O) and amorphous phase in the resulting C-A-S-H mixture; increasing time results in an increased conversion of α-dicalcium silicate hydrate into tobermorite. The amount of K leached from the mixture is relatively constant across all processing conditions. Hydrothermal alteration in autoclave of K-feldspar-bearing rocks such as ultrapotassic syenite permits the synthesis of a potential potassium fertilizer which alkalinity and mineralogy can be tailored according to soil requirements.

May 22, 2020

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009

By Bruce Hebblewhite

Australia’s Minerals Tertiary Education Council (MTEC) has achieved several successes during its first three years of operation. This initiative was developed through the Minerals Council of Australia, in conjunction with three partner universities involved in mining engineering education. The partner universities are the University of New South Wales (UNSW); Curtin University, the West Australian School of Mines (WASM); and the University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and the development of a number of flexible, distance-based delivery programs. This article then discusses future initiatives. Importantly, the challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering: Mining Education Australia (MEA). This will provide a common third and fourth year program to all three universities beginning in 2007. The common program will involve innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process.

Jan 1, 2006

By A. El-Midany

Dolomite impurities are increasing in the currently mined phosphate deposits in Florida. Several research efforts have been conducted in various laboratories around the globe to find methods to economically removing the dolomite. However, a universal and cost-effective process is not now in commercial use. In this paper, a new process for dolomite/apatite separation is presented. The differential solubility of dolomite in slightly acidic solution is utilized to generate micro CO2 bubbles at the dolomite/water interface. Particle (dolomite)/bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro-bubble/particle aggregates. Different surface-active agents were tested to stabilize the bubbles. Results of these tests are presented, and the mechanisms involved are discussed.

Jan 1, 2009

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By James J. Olson

Most of the projects summarized in this paper are funded under the Bureau&apos;s Advancing Metal-Nonmetal Mining Technology program and are part of the in situ mining subprogram coordinated at the Twin Cities Mining Research Center. The borehole mining equipment development, are funded under the Bureau&apos;s Advancing Coal Mining Technology program, is essential to accelerated progress in the in situ mining subprogram, and some background information on this concept is included. The initial in situ research projects started in 1971-72 evaluated some of the critical blast design parameters for in situ copper leaching. The present program totals about $1 million per year and includes in-house research projects, cooperative (cost-sharing) projects with the mining industry, and research and development contracts. Two different extraction schemes are under investigation: inplace leaching and borehole (or slurry) mining. The principal commodity targets for the Bureau&apos;s improved in situ mining technologies include copper, uranium, coal, and potash. The principal purpose of this paper is to inform the mining industry of the in situ mining research recently completed or being conducted by the Bureau of Mines. In addition the Bureau encourages companies to comment on the program accomplishments as well as offer suggestions on top priority research needs for improving the in situ mining methods described in this paper.

Jan 1, 1977

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead&apos;s common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By R. E. Ray

Compared to conventional fully ducted axial and centrifugal fan systems, jet fans can offer a number of advantages for control of smoke during fire emergencies and dilution of diesel engine exhaust products in vehicular and rail tunnels. The success of jet fan applications is the result of a balance between the temperature de-rating of the fan, buoyancy forces and the installation momentum transfer efficiency. This paper provides a case study of a unique application of vertically-mounted jet fans in ventilation shafts used to provide both emergency ventilation and pollution control for an overbuild created by the construction of a series of commercial high-rise residential buildings over a portion of an existing passenger rail line. A detailed evaluation of a set of shafts for one building is presented, including a discussion of the calculation methods used to estimate the required jet fan capacity and the results of the subsequent numerical analysis using Computational Fluid Dynamics to simulate the performance of the jet fans during train car fire emergencies.

Jan 1, 2009

By K. C. Tran

This paper reviews the advancement of measurement technologies for the control of raw materials processes in the basic industries. The combination of digital technology and on line spectroscopy enables the development of intelligent instruments for composition and particle size analyses in real- time high- frequency control conditions. In many industries, the applications result in productivity improvement and energy savings. Plant specific examples include operating experience and benefits realized in sorting, blending and beneficiation processes. Instruments of the future not only measure specific parameters of the process and monitor its own health combined with self-corrective mechanics but also acts with intelligence to effect the quality of the process or regulate the primary apparatus.

Jan 1, 2001

By T. R. Kostecki, A. J. S. Spearing, A. Hyett, M. Gadde

Ground control research for underground coal mining has progressed significantly over the past several decades. With this progression, and the ability to analyze and model underground conditions, underground working conditions have significantly improved. In order to progress further, the behavior of roof support must be known and be adequately modeled, such that models can be used for support design under different geological and mining conditions. This paper discusses the results from a research project funded by the U.S. National Institute for Occupational Safety and Health (NIOSH) and undertaken by Southern Illinois University Carbondale and Peabody Energy. The research involved installation of active and passive instrumented bolts in mines, recording relevant in situ data and then attempting to model the behavior of the bolts as mining progressed. Such calibrated models could aid in design of roof supports under different geological and mining layouts and thus, hopefully, further improve rock related safety.

Jan 1, 2012