Search Documents

By George Anagnostou

Time-dependent ground behavior may have important implications for the construction process or the life of a tunnel. The paper gives a concise overview of the influence of time on the deformations and the stability of underground openings, including topics such as face stability in soft ground or the time-development of pressure or deformations in squeezing or swelling rock. While keeping in mind practical questions of tunnel engineering, emphasis is placed on understanding the observed time-dependency, on the underlying mechanisms (such as pore water pressure dissipation or chemical processes) as well as on the respective inherent prediction-uncertainties and design-uncertainties.

Jan 1, 2007

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By F. M. Doyle

Metal removal kinetics and metal ion selectivity in ion flotation were studied from a thermodynamic perspective. Surface tension data could be used with the Gibbs adsorption equation to quantitatively predict the metal ion removal kinetics in alkylsulfate-Cu systems. However, surface tensions predicted cation selectivity coefficients in the sodium dodecyl-sulfate (SDS)-Cu-Ca and SDS-Cu-Pb systems rather poorly, although the predicted order of the selectivity (Cu2+<Ca2+<Pb2+) was correct. Another thermodynamic selectivity model, which used the Grahame adsorption equation and a geometrical analysis, predicted cation selectivity coefficients that agreed very well with experimentally measured values.

Jan 1, 2000

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

By MATT RENAUD, Mustafa Kumral

Mining corporations have spread their operations worldwide in the last few decades. The reason behind widening operations geographically can be seen as it being part of a risk diversification strategy. Given that the technical, financial and social risks are high, favorable deposits, taxation regimes and legislative frameworks create incentives for international mining operations. On the other hand, international mining activities add the risks of permitting, investing, operating and decommissioning to the corporations. These risks could emerge from defaulting, corruption, resource nationalism, social license to operate, and political and legislative uncertainties and instabilities.

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

The North Singhbhum Mobile Belt (NSMB) lies between two crustal-scale shear zones, the South Purulia Shear Zone (SPSZ) at the north, and the Singhbhum Shear Zone (SSZ) at the south. The Babaikundi-Birgaon Axis (BBA) is an east-west trending secondary shear zone in the NSMB lying south of SPSZ, which is known for the occurrence of gold along with other sulfide minerals within the quartz reefs. The present study has been carried out at north of Ichadih village, which lies on the BBA. The present study attempts combined electrical resistivity tomography (ERT) and self-potential methods along a profile of 470-m length in the Ichadih area to map the potential mineralized zones. Initially, ERT sections generated by Wenner, Wenner- Schlumberger, dipole-dipole, and joint inversion of the combined array have been analyzed, and results are validated through the analysis of model resolution. A prominent low resistivity (10–100 Ωm) associated with quartz reef/limonitic quartz reef at a depth of approximately 30–85 m, encircled by a high resistive (more than 10,000 Ωm) formation associated with metasedimentary rock, has been delineated using joint inversion of the combined array. Further, analysis of self-potential (SP) anomaly using particle swarm optimization inversion also confirms the prominent low SP anomaly at a depth of 77.3 m, which is analogous to the low resistivity anomaly identified in the joint inversion of the combined geo-electric array. Subsequent analysis of a complex synthetic geo-electrical model analogous to the present field situation proves the efficacy of the joint inversion of combined arrays. As a whole, joint inversion of multi-array data is established as an efficient technique for better subsurface imaging in case of the complex subsurface structure. In-depth analyses confirm the possibility of sulfide mineral-rich deposit (quartz reef/limonitic quartz reef) which requires further geological drilling and lithogeochemical sample analysis, for possible future exploration.

Oct 26, 2020

With the advent of the environmental "green" movement of the 1960s, eventually leading to Earth Day 1970, Congress responded by passage of the National Environmental Policy Act (NEPA), 1970. NEPA gave impetus to a flood of federal acts and laws in the subsequent three decades. Many of those protecting man&apos;s environment, health, and well-being also affect mining. For purposes of this chapter, a current mineral law summarization lends itself to a division into two parts: viz., Part I, General Mining Law, and Part II, Enviromining Law. The word enviromining has been coined by the author and is defined and used herein as those federal and state statutes and regulations that were created to provide protection and preservation of man&apos;s environment, health, safety, and welfare, and they have particular application to and affect on mining activities. They are listed and treated under Enviromining Laws in Part II. Mining, as a basic industry to provide the essential minerals for mankind&apos;s necessities and well-being, truly reflects the mining industry&apos;s slogan, "If it can&apos;t be grown, it must be mined." Without the basic minerals and rocks won from the earth by mining and mineral processing for their valuable physical properties or chemical constituents, man would soon be forced to revert to the cave-dwelling age. Unfortunately, for man to survive in the "manner of life to which he has become accustomed," he is caught between the demands of cleaning up his deteriorating environment and a continued supply of his basic requirements and amenities for daily living supplied by mining of the earth&apos;s minerals. He must have "clean living" at the same time with "good living;" neither is expendable. A very high pricetag accompanies this essential and critical choice which must be paid by society. The United States is internationally recognized as the world leader in environmental matters. Many countries are following suit, principally the other Anglo nations. Because US law is founded and based on English law, on occasion, Anglo-American law is referred to and cited as authority in litigation anywhere in the Anglo-American world of jurisprudence. For this reason, and because mining and the industry is international in nature and operations, some British Commonwealth cases will appear in various topics. If the case is of interest to the reader, further inquiry at a law library may be made through use of the case&apos;s style and citation given. "Style" refers to the name of the litigating parties. "Citation" refers to the law publication in which the case and decision may be found, as well as the jurisdiction and court of decision. Citation of cases from the United States and British Commonwealth nations is explained under Case Citation Explanation. Space and time limit exhaustive treatment of subjects and covering all geographic and jurisdictional areas. This chapter is intended as a broad outline and is based on the author&apos;s master&apos;s thesis at the University of Missouri-Rolla, 1992. The following Case Citation Explanation provides guidance on formatting of citations.

Jan 1, 1994

By MUSTAFA ERKAYAOGLU, Muhammet Mustafa Kahraman

Particulate matter (PM) is one of the main actors related to air pollution caused by surface mining. Fugitive dust, considered as particulate matter that cannot be collected by conventional measures, is classified by the particle size. The Environmental Protection Agency (EPA) categorizes PM as coarse and fine particles based on the particle size being less than 10 μm (PM10) and less than 2.5 μm (PM2.5). Basic operations of surface mining such as drilling and blasting, loading, haulage, and processing are processes that can potentially generate fugitive dust. Regulations and legislations enforce the mining industry to use environmental monitoring systems, fugitive dust level measured by PM10 level as part of this. Air quality monitors are positioned at different locations around surface coal mines and track air quality levels during production. This study introduces a data-driven methodology to handle air quality issues related to fugitive dust at surface coal mines. Data is sourced from different mine equipment in real-time and they are integrated with air quality monitoring systems to provide information to support decisions for fugitive dust. The method is implemented and demonstrated in a case study at a large surface coal mine.

Sep 29, 2020

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, coal workers pneumoconiosis (CWP) and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by distributions of particle composition, size or shape). For such analysis, scanning electron microscopy with energy dispersive X-ray (SEM-EDX) may represent a powerful tool. This article is a preliminary investigation of SEM-EDX to characterize respirable dust from an underground coal mine in Central Appalachia. Samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate respirable dust concentrations during sampling. This data was compared to particle densities observed under the SEM. Dust is generally defined as small, solid particles with an effective diameter between 1 and 100 µm. In underground coal mines, dust is produced by a variety of activities such as coal and rock cutting, materials handling, haulage and from a variety of materials. While the coal itself is primarily made up of organic carbon, it is estimated that as much as 60 percent of coal mine dust consists of mineral matter, including clays, metal oxides and sulfides, carbonates, quartz, phosphates and heavy minerals (WHO, 1997). Mineral matter may be ingrained in the coal seam or associated with adjacent or interlying strata, and may also be contributed by specific activities such as rock dusting. When dust is generated or made airborne, suspended particles tend to settle slowly with gravitational forces, but can remain airborne for extended periods of time depending on environmental conditions such as air velocity (Courtney et al., 1986) and particle properties such as size (ISO, 1995; WHO, 1999). Thus, miners working underground are routinely subject to occupational dust exposures ? with highly variable characteristics between and even within mines.

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

By John G. Holmes

The generation of low cost power is but one phase of the TVA program for regional development. During the 36 years since TVA began, growth in its generation of electric power has necessitated a shift from a predominantly hydroelectric power system to a combination steam and hydroelectric system. The addition of steam-electric power plants to TVA&apos;s generating system was necessitated by the rapid increase in the traditional and defense demands for electric power in the 80,000-square-mile area served by TVA, the need to firm up the hydroelectric power, and the fact that all available sites for sizeable hydroelectric projects had been developed. At present TVA owns and operates 40 power plants--29 hydroelectric and 11 steam-electric plants. The total generating capacity of the hydroelectric plants is 3,105,430 kw, and the capacity of the steam plants is 13,951,135 kw. This provides a total generating capacity of 17,056,565 kw for the plants operated by TVA. Individual capacity of the 112 hydroelectric units ranges from 10,000 to 67,500 kw, and the individual capacity of the steam-electric units now in operation ranges from 60,000 to 950,000 kw. In addition to this generating capacity, TVA distributes the power from 6 U. S. Army Corps of Engineers hydroelectric plants on the Cumberland River. These plants contribute an additional 725,000 kw. Also, under an agreement with the Aluminum Company of America, TVA directs the stream flows and generation of their 423,715-kw system on Tennessee River tributaries and shares with Alcoa in the increased generation resulting from this coordinated operation.

Jan 1, 1969

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner&apos;s exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines&apos; remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau&apos;s Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By Toby Mayo, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

The Zoro pegmatite project in east-central Manitoba occurs 20 km east of the historic mining town of Snow Lake. A composite sample (Master Comp) was prepared fromthree pegmatite zones within Zoro Dyke “D1” including the North, Central, and South Zones for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample crushed to ca. P80 of 600 μm to determine the overall mineral assemblage, liberation of spodumene, and assess the potential recovery of spodumene by flotation. XRD and QEMSCAN results show that the sample consists of spodumene (10.5%), quartz (29.3%), plagioclase (29.0%), K-feldspars (21.3%), micas (5.1%), tourmaline (2.9%), and Fe-Mn-phosphates (0.1%). Spodumene is well liberated (88%), but also forms complex particles (7%), and middlings with quartz (4%). Liberation of spodumene increases from 81 in the + 600 μm to 95%in the − 106 μm size fraction. Liberation of quartz, feldspars, and micas account for 89%, 94%, and 83%, respectively. Electron probe micro-analyses and LA-ICP-MS showed that the average Li concentration is 3.7% in spodumene, 2196 ppm in micas, 1001 ppm in tourmaline, and 115 ppm in K-feldspars. Thus, spodumene accounts for 96%, micas 2%, Fe-Mn phosphates 1%, and both K-feldspars and tourmaline for < 1% of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other than spodumene carriers. Heavy liquid separation was conducted on the Master Comp which was crushed to − 6.4 mm, while the − 600 μmfractionwas removed fromthis test. The coarse fraction − 6.4mm/+ 600 μmwas subjected to HLS tests with eight heavy liquid-specific gravity cut-points (2.65 to 3.10 g/cm3). HLS indicates that it is possible to produce a high-grade lithium concentrate (close to 6% Li2O) after the rejection of iron silicates with magnetic separation.

Sep 16, 2020

By Jorge Ferrero, Andreas Raedle, Uhland Konrad, Michael Dutton, Keivan Pak Iman, Walter Trisi

Strabag, in partnership with Arup, is constructing the Advance Tunnel for the Scarborough Subway Extension (ATSSE); a project by Metrolinx and Infrastructure Ontario (Sponsors). The 10.7 m internal diameter single bore tunnel represents a significant departure from the traditional arrangement of twin subway tunnels in North America. ATSSE is the first-time steel fibers are used to solely reinforce a tunnel of this size in Eastern Canada. This paper discusses the challenges with design and acceptance of SFRC segments and the state-of-the-art numerical models employed to check the joint performance. The advance procurement approach for TBM and PCTL’s procurement to accelerate the project schedule is also presented.

Jun 13, 2023

By H. M. Brennecke

A new hydrometallurgical process has been developed to recover copper from sulfide ores. Copper is leached in a staged reactor system utilizing nitric and sulfuric acids at 105°C. Iron is removed from the pregnant liquor as a jarosite and cathode copper is electrowon directly from the purified pregnant liquor. The spent electrolyte is recycled. Nitrogen oxides evolved from the leach are reconverted to nitric acid and are also recycled. Sulfur is rejected as S°, jarosite and gypsum. The process is highly versatile and can recover precious metals, molybdenum and zinc, when these elements are present. Continuous, integrated, semi-pilot plant operations using chalcopyrite ores demonstrated 99% copper leaching and production of cathode grade copper. Economic evaluation shows that the process is competitive with pyrometallurgical and other hydrometallurgical processes.

Jan 1, 1978

By V. L. Andrade, K. L. C. Goncalves, N. A. Santos

This paper describes results obtained in a test program performed with new equipment, called Mini Pilot Plant, manufactured by Canadian Process Technologies. This equipment was acquired by CVRD aiming at testing flotation circuits, in a continuous closed configuration, with samples obtained from drill cores. Success of this goal would allow CVRD to establish the metallurgical performance of mineral deposits with more confidence in comparison to Locked Cycle Tests (LCT). This paper discusses the importance of assessing the ore variability and compares results obtained in LCTs and Mini Pilot Plant. Results suggest that more reliable data is obtained in MPP test.

Jan 1, 2002

By L. Echeverri

Research studies have shown that the flow within feedwells displays a vortical structure and high velocities at the locations where standard tangential inlets force its way into the feedwell swirling flow, producing high local shear rates and flow non-uniformities. These hydraulic deficiencies can be attributed to the discrete feeding through a few entrances, usually one or no more than a few tangential feedpipes, which practically project jets into the vortex within the feedwell. The main consequences are unequal flocculation with aggregates subjected to different amounts of shear and a non-uniform discharge from the feedwell. This paper presents results on the application of CFD and small-scale models to develop a new design that overcomes these problems by using an involute shaped inlet that converges around the feedwell. The result is a new feedwell with enhanced hydraulics that perfectly couples with the FLSmidth E-Duc® Feed Dilution system by protecting the flocculated aggregates that have been carefully produced upstream, and that favors uniform sedimentation conditions within the thickener thanks to a uniform discharge, while maintaining a practical and trouble-free geometry with excellent turndown.

Jan 1, 2012