Search Documents

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

The Sage Mill Project w approved by Santa Fe Pacific Gold Corporation's Board of Directors in October 1994. The Sage Mill Project included a pressure oxidation plant designed and constructed to process refractory carbonaceous ore using fine grinding/autoclaving technology developed specifically to treat Twin Creeks ore. The project was constructed in two phases. The first phase was put into operation on May 5, 1997, just hours before the transfer of ownership to Newmont Gold Company occurred. The second phase started in October 1997. This paper reviews schedule, costs, scope changes, and methodology used on the project that spanned almost five years from project definition through commercial operation.

Jan 1, 1999

By P. Rostami

It is important to study the ventilation system in order to better design and control of the working environment in deep underground mines. With increasing depth, heat, and humidity performance may be reduced and impair the attention of workers. The purpose of this paper is to apply a complex; development-end model configured in the MULTIFLUX program, developed at the University of Nevada, Reno, USA. The MULTIFLUX development-end model template has been benchmarked against measurement results from two UK coal mines in previous studies. The present study is a test of MULTIFLUX application in a metal mine. The model incorporates the simulation of the air flow field in the drift and the auxiliary air duct; simultaneous heat and humidity transport from the drift wall; heat and mass exchange between the air in the drift and the ducts; and the evaporation of process water and/or condensation of vapor as governed by the psychometric conditions. The results are compared with field data, measured at the Lucky Friday Mine (LF) in Idaho, USA, an underground mine and also shown between the results from the MULTIFLUX-based model, and those from another program, Kduct, developed at the Kyushu University in Japan.. Gao, K. Uchino & M. Inoue Fukuoka, Japan (2002)?

Jan 1, 2011

By K. K. Bhattacharyya

Vast deposits of lignite occur in the Gulf Coast states and northern plain states. Lignite resources are cited to be over 43 billion tons in the Gulf Coast states. An additional resource of 16 billion tons are reported in North Dakota (Jackson, Smith, 1981). All lignite in the U.S. is mined at present by the open pit method. Draglines and scrapers are primarily used to remove the overburden. Bucket-wheel excavators are also being considered for new mines in the planning stages. Lignite seams are mined using front-end loaders, shovels and trucks, or Easi-miners. The depositional environment of lignite is weak sedimentary soils and rock. Ground water is often encountered within the mining depth. Surface water resulting from heavy rainfall or snow melt contributes to the problems of mining. Mining depths of up to 60 m (200 ft) are under consideration. Draglines exert additional loads on the highwalls and spoil piles. The combination of any number of these factors may cause instability of the slopes. Bearing pressure, trafficability, and settlement can also be a problem for excavation and loading equipment.

Jan 1, 1982

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, Colorado, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained, and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward sloping (20 pct) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By Botelho Junior, Amilton Barbosa, Denise C. R. Espinosa, David B. Dreisinger

Copper and cobalt can be found on nickel laterite ores, and cobalt can be found also on copper ores, and many contaminants such as iron, aluminum, and magnesium are associated with these ores. In hydrometallurgical process, a purification step is necessary after leaching due to the presence of these impurities. Chelating resins are more selective for some metals than others, making them more efficient than cationic resins. This overview discusses chelating resin applications to recover copper, nickel, and cobalt from mining process and mining tailings and the effect of contaminants in leach solution. Chelating resins with iminodiacetate functional group can be used for selective copper recovery, and both iminodiacetate and bis-picolylamine resins are highly selective for nickel and cobalt. Chelating resins with the same functional group can have different performances on the kinetics of loading, because of variations of structure, the density of functional group, and degree of cross-linking. This article reviews commercial chelating resins that can be applied in leach solutions with different compositions, and also possible innovations for uses of chelating resins to recover metals from mining process and mining tailings.

By Syd S. Peng

Coal mine ground control is the science of the application of rock mechanics principles to coal mining operations. More acceptance of ground control techniques by the US coal mining industry has been seen in the 1980s. It has been demonstrated many times that a proper ground control design is key to a successful coal mining operation. However, numerous in-mine applications of various ground control techniques by the author indicate that cur¬rent techniques need improvement. The biggest problem in coal mine ground control is that miners are dealing with materials of rapidly varying properties and occurrence. And only the exposed surface can be identified positively. Thus, in attempting to solve the ground control problems, many unknown factors are assumed. Some of these problems deriving from such assumptions are discussed here. Coal pillars There are two types of coal pillars - barrier and chain pillars - depending on the purpose. Barrier pillars are those located between panels or sections or mines. Their objective is to isolate the mined-out effects of one from the other. Chain pillars are characteristic of room-and-pillar mining. They are designed to support the overburden load and protect the surrounding entries and crosscuts. Pillar design is the most popular and, frequently, the only ground control technique employed by coal operators for mine design. There are many pillar design formulae available (Bieniawski, 1983; Peng, 1986). Nearly all consider both size and width/height effects. Specifically, pillar strength decreases with increases in pillar size and increases with increase in the ratio of width to height. However, the manner of those changes varies with investigators. Consequently, the pillar size determined varies considerably from investigator to investigator. And the variation grows much more pronounced as the seam depth increases (Fig. 1). The question, then, is which one should be used? One may say each formula is developed for a particular coalfield. A particular formula may have been used to design a pillar, which has not failed. Does that mean it was over designed? Not necessarily, because no one can confirm its stated "safety factor." Recent case studies (Peng, 1986; Tang and Peng, 1988) show that all pillar formulae are too conservative for chain pillar design in room-and-pillar mines due to the following two problems: • Uncertainty about in situ pillar strength. All formulae employ uniaxial compressive strength of selected samples tested in the laboratory and scaled to that for underground pillars. The scaling factors are not well proven. In situ testings by Bieniawski (1969) suggested that 1.5 m (5 ft) pillars are representative of in situ pillars that, after being tested in various US coal mines, are not universally applicable. • Uncertainty about the actual loading on the pillar. The most frequently used tributary loading theory defines the loading as total overburden weight tributary to each pillar (from roofline to surface). This is too conservative when it applies to coal measure rocks. The overburden consists of layered strata of different stiffness. Many stiffer strata will self-support over small roof spans. Depending on the location of these strata above the coal seam, it will reduce pillar loading in various proportions. It follows that total structural analysis using, for instance, finite element method is more appropriate. It can take into account the interaction of roof and floor strata with coal. This has been demonstrated by Peng et al. (1986,1988) on several case studies. However, the validity of the finite element structural analysis depends on the accuracy of in

Jan 1, 1989

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific and the U.S. National Institute for Occupational Safety and Health (NIOSH) combined efforts to evaluate an in situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was preloaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both realtime and time-weighted-average approaches. The real-time measurements were performed with a Model AE33 aethalometer, and filter samples analyzed by the NIOSH 5040 method were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82 to 89 percent. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the aethalometer were higher, possibly due to differences in the performance of the size selectors used for the two methods: impactors versus cyclones. More research is required to develop a robust correlation between the two methods to support the use of the aethalometer in future mining applications. The advantages of the aethalometer are that it can measure and record DPM levels for weeks at a time and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally, such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise in reducing DPM concentrations in the mine environment.

Mar 1, 2017

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By R. Benito

This paper describes the application of modern data-analysis tools, such as data mining, to determine a representative cost driver for haulage activity. This cost driver was subsequently used to trace incurred haul costs by bench for openpit optimization. For this purpose, large amount of previously unused cost and production data from an open pit mine was extracted, loaded, transformed and integrated into a data warehouse. Predictive modeling was performed using Microsoft Decision Trees algorithm to compute expected unit haul costs by bench for future mine expansions. Finally, a sensitivity analysis was carried out to determine the effect of two cost drivers (if any) for incremental haul costs in the final pit outline process.

Jan 1, 2008

By Jr. Hawk

The power generation industry may be required to reduce CO2 emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By S. Holtermann

Through the process of Riverbank Filtration (RBF), the Louisville Water Company plans to obtain a higher quality source of water for their B.E. Payne Water Treatment Plant (WTP) by means of four collector wells located in the alluvial aquifer along the bank of the Ohio River. The collector wells are connected to a 2,850 L/s (65 mgd) pumping station by a 2,362 m (7,750 ft) long, 3 m (10 ft) finished diameter tunnel located in limestone and shale bedrock, which is approximately 45 m (150 ft) below the surface. High tunnel boring machine (TBM) production rates were achieved in this moderately weak bedrock; most of the tunnel only required support in the crown. An unanticipated water-bearing fault and unanticipated ground behavior proved challenging and required quick thinking to minimize impacts to construction. Tunneling conditions are discussed in detail, together with the methods used for overcoming the groundwater and ground behavior challenges. The tunnel is expected to be completed in April 2009.

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By N. Dhawan

With ever-increasing demand, low-grade complex ores and strict environmental regulations, metallurgical processing options have become limited. Heap leach technology provides several benefits to combat these issues including low cost, flexibility and diversified process conditions. This paper provides an overview of heap leaching technology with specific emphasis on chemical aspects. Hence, influencing factors, advantages and disadvantages, testing approaches and some fundamentals will be discussed. Finally, heap leach technology for different ore types (copper, nickel, uranium and gold) will be briefly compared.

Jan 1, 2012