Search Documents

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10?40 km in length. These road networks are often not optimally designed and maintained and as a result, identifying and remediating road functional defects is problematic. Most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. This paper presents a haul road maintenance management system which utilizes an assessment of rolling resistance based on a functional performance evaluation of a haul road, together with mine haul truck operating cost models to derive the optimal frequency of road maintenance. A typical application is presented which illustrates the potential of the technique to manage maintenance as and where needed with resultant reduction in total road user costs and an improvement in service provided for the road user. Keywords: Haul road, surface mining, road maintenance, transportation, pavement design

Jan 1, 2003

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

In recent years several mine researchers have studied the optimization of cutoff grade with the purpose of maximizing Net Present Value (NPV). The best and most popular one is the Lane algorithm. Based upon the Lane algorithm it is possible to calculate the optimum cutoff grade for mine, mill, and refinery capacities for single metal deposits with variable grades. The Lane algorithm cannot be used in multiple metal deposits. The reason is that, while in single metal deposits six points are possible candidates for the optimum cutoff grade, in multiple metal deposits an infinite number points are possible candidates for the optimum cutoff grades and objective function evaluation of these infinite points is impossible. In this study the Golden Section search method was used to calculate optimum cutoff grades of multiple metal deposits for the same conditions as Lane assumed in single metal deposits. Based on this method, grade-tonnage distribution uncertainty space of problem is guessed. In the next step, by selecting test points in uncertainty space and evaluating the objective function at these points, a part of uncertainty space will be eliminated. The procedure is then repeated until the uncertainty space has been sufficiently reduced to ensure that the optimum cutoff grades have been located to the required accuracy. Key words: Optimum cutoff grades, Optimization, Net Present Value (NPV), Golden Section search method

Jan 1, 2003

By F. T. Cawood

The new South African Mineral Policy has major implications on the way mineral rent will be collected and shared between the stakeholders in future. Although the policy does not supply details on how this will be done, drastic departures from practices under the previous dispensation require a new approach. For example, there introduction of the ?right to mine? principle implies that the repealed lease consideration concept will be expanded to all minerals. The new policy also makes provision for predetermined standard terms and conditions for all prospecting and mining permissions. It also states that, regardless of whether the mineral rights are state or privately-owned, all prospecting fees and mineral royalties will be determined by state officials after consultation with the registered holder of the mineral rights. This paper proposes a standard mineral royalty formula that complies with the principles mentioned in the White Paper and has been shown to be internationally competitive.

Jan 1, 2001

By C. Musingwini

Traditionally, mineral reserves management at most underground mines in Zimbabwe focus on maintaining large mineral reserves so that the time between development and production is as long as possible. Historical data at Shabanie mine, a Zimbabwean sub-level caving underground mining operation, confirms this practice. However, the high cost of underground development means that the luxury of large buffer mineral reserves cannot be justified. Furthermore significant increases in the costs of production, exacerbated by the current unfavourable economic climate, make the wisdom of extending development workings well ahead of use questionable. Poor ground conditions at Shabanie mine, mean that some development ends have to be re-mined two or three times due to partial or complete closure between the time they are mined and the time they are utilized. In order to reduce the inordinately high support costs associated with closure of development ends a new ?just-in-time? (JIT) approach that provides development ends as and when they are needed, has been adopted. Accordingly a model to determine an appropriate ?just-in-time? rate of development has been created. The JIT development model indicated that the mine could reduce development rates from 330 m/month in 2001, to 160 m/month in 2002 and achieve savings of about 50% on annual support costs, but still assure customers of a long-term product supply. The mine accepted the model in November 2001 and began implementing it in 2002. Results of the implementation will be reviewed in 2003.

Jan 1, 2003

Council for 2005/2006 President W.H. van Niekerk President-elect R.P.H. Willis Vice-presidents Senior R.G.B. Pickering Junior A.M. Garbers-Craig Immediate Past-president F.M.G. Egerton Honorary Treasurer J.A. Cruise

Jan 1, 2006

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 24th August, 1977. Dr M. D. G. Salamon (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : C. G. Evans, J. P. Rees, Life Fellows ; S. R. Bryant, H. MacConachie, M. Mrost, and A. W. van Zyl, Fellows; L. T. Campbell-Pitt, F. W. Collins, A. J. Duncan, I. G. Evans, F. W. Kleinschmidt, P. L. Vaughan, R. W. Wallace, and H. Wason, Members. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on 23rd March, 1977, as published in the June issue of the Journal? Agreed.

Jan 1, 1978

By K. Collett

Elandsrand started shotcreting back in 1991. This paper will share the experiences of the mine by looking into the past, the present situation and the way Elandsrand plans to approach the future. It looks at the application of drycrete and discusses the factors that led to the introduction of wet fibre reinforced shotcrete. The logistical constraints of getting shotcrete material underground will be solved by the development of an underground batch plant, using run of mine waste rock as an aggregate.

Jan 1, 1998

By D. J. Burger

This paper will highlight the system components of a successful underground mining automation project recently launched at DeBeers Finsch Mine. It will also show that integration of short-term mine planning with other upstream and downstream mining processes in the extraction of kimberlite ore from a block cave is not just critical to the future sustainability of this underground mining operation but also for profitability and cost-effectiveness. This paper will discuss the information data flow required from the mine-planning process through to production for underground block cave mining. The benefits associated with this type of integrated mine planning and automation system will be highlighted.

Jan 1, 2006

By J. F. Curtis

In the synopsis, the author concludes that ?high levels of seismicity do not coincide with high rockburst rates?. Implicit to an appreciation of this statement is the necessity of a common understanding of what is understood by the terms: ?high level of seismicity? and ?high rockburst rates?. With respect to the former term there is no difficulty in that the level of seismicity is traditionally measured in terms of the Richter Scale. The latter term however presents a problem in that the author defines it as a particular sort of seismic event?viz: ?Rockburst? is understood as a seismic event that causes damage to an underground excavation with subsequent injury, loss of material/equipment or production shifts? (p. 322). No scale is given of the amount of: ?excavation damage ?level of injury ?material/equipment loss ?production shifts lost whether separate or cumulative, for a particular seismic event to be classified as a rockburst. A further difficulty arises in that in common usage the words ?rockburst?, ?seismic event? and ?earthquake? are all used to describe the same event.

Jan 1, 1999

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By B. J. Madden

Over 206 million tons of hard coal were mined in South African collieries in 1996. Some 132.5 millions tons came from underground operations and approximately 120 million tons came from bord-and-pillar workings resulting in between 100 000 and 150 000pillars being formed. Coal pillar design remains a significant feature of South African mining. This paper reviews South African coal pillar design procedures in the light of 90 pillar collapses that have occurred since 1904. It shows that, while the current pillar strength formula is still valid within the original empirical range of Salamon1,cognisance must be taken of local conditions. Current South African coal pillar research is attempting to account for the variations in local conditions with the emphasis on the effect of discontinuities and pillar deterioration. It is suggested that a more holistic approach to pillar design be adopted to include a design methodology that examines the stability of the roof, pillar and floor of the underground workings. Using this approach, deviations from the empirical database used by Salamon and Munro will be incorporated into the design methodology resulting in more stable underground workings.

Jan 1, 1998

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By H. J. Glass

Collection, preparation, and analysis of blasthole chippings is expensive. Frequently, interpolation of grades at unsampled locations is considered using techniques like kriging. A pre-requisite for kriging is that an experimental variogram is established. In order to assess the quality of the experimental variogram, a measure is developed in this paper. The measure is derived from analysis of the time-honoured expression relating the variance, semivariance, and covariance. It reflects the weighted average deviation of the summed semivariance and covariance from the biased variance. The proposed measure allows assessment of the influence of key variables on the quality of the variogram. Using simulated data, it follows that the quality improves with an increasing number of samples, increasing density of the sampled locations, increasing regularity of the sampling pattern, and increasing uniformity of grades in the absence of correlation. Application to real data shows that the minimum number of samples could coincide with a marked decrease in the value of the measure. Establishing a threshold value is subject to further research. Keywords: variogram, variance, covariance, semivariance, minimization, sampling.

Jan 1, 2003

By J. Glazewski

The mining industry in South Africa has developed its own environmental guidelines in the form of an Aide-Mémoire1,which is an extension of the previous rehabilitation provisions to include all aspects of the environment and all phases of a mining operation. This development, at the time, recognized an international trend towards the formalization of environmental management in mining practice, which resulted from the realization of the large environmental liabilities that mines could face, particularly on closure. Over the past decade the international environmental focus in the mining industry has moved from operational management, to the reduction of liability on mine closure. Mine closure guidelines are being developed internationally by nations (for example, SRK, 19982) and by large mining groups (for example, Rio Tinto, 19983). In South Africa the Department of Minerals and Energy (DME) is presently reviewing the Aide-Mémoire to bring it in line with international and local developments and a separate mine closure plan is being considered.

Jan 1, 2000

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002