Search Documents

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By Y. Wang, S. Sridhar, B. Coletti, G. N. Shannon, S. Vantilt

The final removal of inclusions in the ladle, tundish, and mold in a continuous casting process involves the kinetic steps of liquid film drainage, interface rupture, and absorption of the inclusion into the overlaying molten slag. During this process, oxide inclusions can undergo chemical reactions with the slag. This paper presents recent results on imaging the slag/steel interface and elucidates the evolution of Al2O3and Al2O3-CaO inclusions during their separation from the steel and on their incorporation into the slag. Experimental results, obtained through a Confocal Scanning Laser Microscope, are compared with thermodynamic predictions.

Jan 1, 2004

By J. Böhlke, B. Friedrich, E. Hecker

The legislation for the disposal of heavy metals contaminated substances is still going to be tightened up in the future. The main criteria for the utilization or deposition of these residues are the content and the water solubility of these metals. Through this, the use of slags from the lead-and zinc-industry in road building may become limited or even not possible at all. From an economic point of view this would lead to Pb/Zn losses and costs for safe dumping. This paper investigates the feeding of the reducing agent via hollow electrode DC smelting and the yield of metal reduction. After carrying out thermodynamic calculations, the process window conditions for electric-arc furnace tests were determined. Doing this, the zinc could be reduced, evaporated and recovered as an oxidic intermediate product flue dust, while the lead was present either in flue dust or in metallic form. The zinc content in the final slag could be reduced by up to 90%. The slag product has undergone an eluation test which allows it to be used as building materials. Keywords: zinc reduction, lead reduction, hollow electrode, slag treatment, electric arc furnace

By S. M. Spottiswoode, J. A. L. Napier, M. Kataka

The move away from the use of strike stabilising pillars at depth and the adoption of the more flexible system of mining towards final dip remnant pillars brings new opportunities for optimising mine design. In the initial planning stage, the size and spacing of the final pillars is designed using classical design criteria, through limiting modelled values of Energy Release Rate (ERR), Average Pillar Stress (APS) and Excess Shear Stress (ESS). In reality, mines often leave pillars that are larger than those originally designed. One of the reasons for leaving more ground is an unexpectedly high rate of seismicity. In this paper, we present developments in integration of modelling and seismicity that are aimed at developing design criteria that are more responsive to local conditions.

Jan 1, 2003

By M. F. Dlamini

The hydrodynamics of a hydrocyclone present a complex internal flow structure, the numerical simulation of which remains a non-trivial task. We report on three-dimensional water-only computational fluid dynamics (CFD) hydrocyclone flow field predictions and highlight some of the issues concerned with the development of a CFD model incorporating an air core. The potential for the application of CFD as a hydrocyclone design tool is also discussed. Physically realistic velocity profile predictions were obtained, which challenge the classical account of the hydrocyclone radial particle classification mechanism. A pressure field distribution consistent with literature reports was also predicted. Keywords: hydrocyclone, computational fluid dynamics (CFD),classification mechanism

Jan 1, 2005

By B. Das

he flotation studies on hematite were carried out using di (2-ethylhexyl) Phosphoric acid (D2EHPA) as the collector. The possible mineral reagent interaction was studied through electrokinetic and dissolution studies. The shift in zeta potential (PZC) and decrease in dissolution of iron in the presence of D2EHPA indicated that D2EHPA was specifically adsorbed on hematite surface. The adsorption imparted necessary hydrophobicity for flotation of hematite. Hematite could be floated selectively from hematite and quartz synthetic mixture. Key words: Hematite, D2EHPA, flotation, electrokinetics, dissolution.

Jan 1, 2003

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and downstream processes. In order to take effective measures to reduce their recovery in flotation, an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2005

By R. J. Kendall

As we enter the new millennium, the South African mining industry has to ensure that it becomes more competitive if it is to survive in the ever more demanding global environment. Traditionally, mechanization in narrow stopes has been limited to the use of scraper winches, and numerous mechanization attempts have been restricted to pilot projects operated on an extremely limited scale (with varying degrees of success). The benefits of hydropower are well documented, and Northam Platinum has shown these benefits to be achievable on a mine-wide basis. However, the equipment originally developed for hydropower systems has followed the traditional labour-intensive approach commonly used in deep level narrow stoping operations. The problems experienced with the hydropower system are discussed and the rationale for developing alternate technologies is explored. The hydropower system has shown to be a versatile powering medium which can be harnessed for a diversity of uses. It (hydropower) enables the mining engineer to change traditional paradigms and to design an entirely new approach for optimizing the mining operation based on explosive techniques. The system developed for Northam consists of the following: ?Purpose-built stope drill rig operated off the hydropower system with special features to ensure accurate drilling patterns throughout the length of the blast hole ?Purpose-built high rate cleaning system for rapid transfer of fractured ore to the stope orepass ?Redesigned stope layout to facilitate in-stope water control and to recover fines from the run-off water ?Purpose-built drill rig for rapid establishment of reef raises and advanced strike gullies ?Purpose-built drill rig for flat end development. On both types of development end rig, emphasis is placed on ensuring accurate drilling patterns throughout the length of the hole to maximize linear advance per blast. The paper discusses the implementation of the Northam system on a large scale as well as current initiatives to further improve on the efficiencies of mining operations. It concludes by emphasizing that mechanized hydropowered stope technologies are in their infancy and thus offer unlimited scope in progressing beyond today?s paradigms to present as yet unthought of solutions for optimizing deep level ore extraction.

Jan 1, 2000

By R. Rampersadh

Paper written on project work carried out in partial fulfilment of B Eng (Metallurgical Engineering) degree Steel was sampled after calcium treatment, to follow changes in inclusion composition during the processing of alumium-killed steel into continuously-cast billets, at Mittal Vereeniging. There is some shift in the distribution of inclusion compositions towards alumina, as the liquid steel moves from the ladle to the tundish. This shift may reflect some reoxidation. However, the effect on inclusion modification is small, since only a small fraction of the tundish oxide inclusions is fully solid?which agrees with the plant observation that these heats cast without clogging. Magnesium oxide in the inclusions contributes to liquid formation, substantially increasing the range of lime: alumina ratios over which the inclusions are partially or fully liquid.

Jan 1, 2006

By S. Rolseth, J. Thonstad

The traditional electrolyte for aluminium electrolysis is based on molten cryolite (Na3AlF6), acting as solvent for the raw material, alumina (Al2O3). Over the years there has been a trend to increase the content of excess aluminium fluoride (AlF3) to the cryolite-based electrolyte, in order to enhance the current efficiency of the process. In most cases one has ended up at 11?13 wt% excess AlF3because higher contents makes it difficult to control the heat balance of the process. This problem may be overcome if sensors are developed that will allow online control of electrolyte temperature and composition, and we may then see a surge towards still higher AlF3contents. In the development of new anode materials to replace the carbon anode with inert, oxygen-evolving anodes, focus is on anode corrosion, and a low electrolyte temperature is then highly desirable. While the conventional process operates at around 960°C, electrolyte temperatures as low as 750°C are being tested. This is achieved by having large excess contents of AlF3(40 wt%). The consequences of using such electrolyte compositions are discussed.

Jan 1, 2004

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

By J. M. Ortiz

Mineral resource evaluation requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Usual practice is to consider the domain boundaries as hard, i.e. data from across the boundaries are disregarded when estimating the grades within a given domain. This practice may hinder the quality of the estimates when a significant spatial correlation of the grades exists across the domain boundaries. In this paper, several geostatistical methodologies to handle soft geological boundaries are compared through a case study on a copper mine in Chile. The estimation methods considered are: ordinary kriging using hard boundaries between geological domains; ordinary kriging omitting the geological boundaries; traditional and standardized ordinary cokriging of the grades assayed in different domains; ordinary kriging within dilated geological domains, that is, incorporating samples from adjacent domains up to a given radius from the boundary of the domain being considered. The estimations are performed using a set of exploration data (drill hole samples) and are validated using a set of production data (blast hole samples collected for grade control). Results indicate that kriging with dilated domains performs better than ordinary kriging using hard boundaries or no boundaries and better than the ordinary cokriging approaches. It therefore appears as a simple alternative to global kriging (without considering the geological domains) and allows accounting for changes in the grade average, dispersion and spatial continuity with the geological characteristics of the deposit, via the use of grade variograms proper to each geological domain. The maximal distance for searching samples from adjacent domains should be chosen according to the spatial correlation of the grades across the domain boundaries, or via a cross-validation at an early stage of the mine or a jack-knife if production data are available. Keywords: Kriging; cokriging; soft boundaries; hard boundaries; geological control; geological domains.

Jan 1, 2006

By O. I. Ostrovski, D. K. Belashchenko

The aim of this paper is the construction of models of systems with ionic and ionic-covalent bonds (molten salts) using experimental diffraction data and the calculation of their structure and thermodynamic and transport properties. Modelling was performed using algorithm BELION, in which the non-coulomb part of interaction potential between ions in the model was determined by the method of iterative simulation which targeted agreement between calculated and experimental partial pair correlation functions (PPCFs). The ionic charges in salts, which can be fractional, were determined by minimization of internal energy. In this paper, the algorithm BELION is applied for chlorides of alkaline-earth metals. Pair potentials, PPCFs, atomization energies, self-diffusion coefficients and electric conductivity are calculated. The charge of alkaline-earth metals was in the range of 2.0-2.1, slightly increasing from Mg to Ba. Partial pair correlation functions and atomization energies of models agree well with experimental data for MgCl2, SrCl2and BaCl2. Keywords: molten salt, molecular dynamics, partial pair correlation function, ionic charge, atomization energy, diffusion.

Jan 1, 2004

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By M. Wang, Z. Sui, T. Lou

After smelting, the associated mineral ore accompanying Valuable Metal Compounds (VMC),such as titania and borate in BF., most of the VMC were separated from the metal into the molten slag that is an associated slags. Based on several case studies in laboratories and in a practice in a pilot plant on the associated slags , there occur a feasibility to recovery VMC from the slags by anew process- Selective Precipitation Technique (SPT) on which three continuous steps are involved: (1) The selective enriching the dispersed VMC into a designed mineral phase in the molten slag; (2) The selective coarsening the designed mineral phase with large crystal grain size;(3) The selective separating the coarsen phase from tailing by mineral dressing or hydrometallurgical process . Some results on the recovering the VMC from the associated slags by SPT were summarized as examples in present paper. Keywords: selective precipitation technique, associated slag, recovering metals from slag.

Jan 1, 2004

By A. M. Clegg

In general, overall experience has shown that the approach to the appointment of a project manager is given much attention, but little specific attention is given first to the risk associated with the project conceptual design and its overall executability within either the new legislative framework or the sustainability of the outcome. The risk in project executability and sustainability within the ?new age? legislative framework of the Mining Charter, etc, is itself however, of far greater importance. The degree of importance being defined by the intended projects impact on the business going forward. This is particularly the case where the intention of the implementation is effectively to turn around or even enhance a loss-making strategic investment like a mine or process plant operation in an ?old-order rights? or Brownfield?s operation. This paper attempts to highlight the importance of a ?pre-project project? (PPP) to mitigate the risk in the ?new age?, with specific reference to operational due diligence (ODD) and project conceptual design.

Jan 1, 2005

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004