Search Documents

By D. D. Marsden, L. E. Kun

Although a regulation is in force that all water used underground shall be free of bacterial contamination, in practice it is often very difficult to accomplish this. The standard method of disinfection m South African mines IS treatment with calcium hypochlorite, although liquid sodium hypochlorite is used at a few sites. Primarily because the process depends on human control for the addition of the hypochlorite and the regulation of its now, it is frequently found difficult to disinfect mine water adequately and continuously. In many marine environments, chlorine generated by the electrolysis of seawater in its passage through an electric cell is used for disinfection. The generation procedure is continuous and needs no human control except for occasional checking of the equipment. This paper describes the successful implementation of the process, suitably .modified, .at four underground sites. After severe scaling problems had been overcome, a procedure resulted that chlorinates considerably more effectively than the previous system (dosing with calcium hypochlorite), and that has a lower amortized operating cost.

Jan 1, 1981

By H. M. Friede

Notes on the composition of pre- European copper and copper-alloy artefacts from the Transvaal by H. M. Friede. Ph.D. (Visitor) Seven copper artefacts (five ingots and two ornaments) found at prehistoric sites in the Transvaal were submitted to analysis. All the artefacts showed a high copper content and a relatively Iow level of impurities. A little-known ingot type from the Limpopo Valley ('nail' ingot) is described, and its analysis is given. The analysis of two copper ornaments that come from sites dated to the 5th Century AD. and the 11th Century AD. showed the constancy of the composition of copper articles over long periods. The well-known 'Blaauwberg Ingot' was re-analysed, and the results showed that this ingot cannot be regarded as a true bronze. Analytical values for the composition of three brass artefacts from Bambandyanalo (Mapungubwe), Northern Transvaal, are given. Some aspects of pre-European bronze manufacture and brass smelting, and of early metal trade from the East Coast into the interior of South Africa, are discussed.

Jan 2, 1975

By Gernot Beer, Christian Dünser, Marcos Noronha

The main findings of the joint research initiative “Numerical Simulation in Tunnelling” and a follow-on project on efficient numerical simulation models for tunnelling are presented. Die wichtigsten Resultate des Forschungsschwerpunkts „Numerische Simulation im Tunnelbau“ und einem Folgeprojekt über effiziente numerische Simulationsmethoden werden präsentiert Les résultats les plus importants du point principal de la recherche "simulation numérique dans la construction de tunnels" et un projet consécutif sur des méthodes de simulation numériques efficaces sont présentés

Jan 1, 2003

By T. P. Chidakwa, T. R. Stacey

This study investigated the corrosion rates of various steel types and coatings used for friction rock stabilisers in a deep-level gold mine under diverse underground environmental conditions. Testing was conducted in situ within ramps, intake airways, and exhaust airways, and through simulated laboratory experiments. Results revealed that environmental variations significantly influence the corrosion performance of different materials and coatings. Duplex coatings, made up of galvanised steel with an organic paint layer, demonstrated the highest corrosion resistance. Zinc-based coatings provided moderate protection, while 3CR12 stainless steel and uncoated S420 carbon steel exhibited comparatively poor resistance under both aqueous and atmospheric conditions.

Mar 4, 2025

By A. G. Journel, CH. Huijbregts

"Centre de Morphologie MathématiqueSpecial problems arise in the evaluation of lateritic-type orebodies (Ni-Co, bauxite) or, more generally, orebodies affected by surface weathering. In this type of orebody, the vertical grade distribution shows, from the hangingwall downwards, a systematic increase followed sometimes by a certain decrease, or vice-versa. These trends appear together with irregular variations from one drill bole to the other.The problem is to characterize a vertical structure that is representative not only of the drill hole but of an entire panel or zone of influence, in order to define mineable thicknesses for given cut-off grades. The vertical grade distribution observed on the drillhole is replaced by a new curve, called 'derive' (drift), which is computed by 'universal kriging'.Once the vertical study is completed, new 'service-variables' are defined in the horizontal plane, such as mineable thickness and the corresponding average grade, economical functions (combination of the grades of several minerals). The local and global estimation of these variables can then be performed by a simple bi-dimensional kriging plan. The global estimation is summed up by several tonnage-cut-off grade curves.The practical valuation according to the above scheme of a New Caledonian lateritic nickel orebody is presented."

Jan 1, 2014

1. Book reviews Geostatistics for natural resources characterization, edited by G. Verly, M. David, A.G. Journel, and A. Marechal. Hingham (MA 02043, U.S.A.), D. Reidel Publishing Co., 1984. Pt I: 606 pp. Pt 11: 518 pp. U.S.$135,50 per set. Reviewer: D.G. Krige Magnesium, the international perspective, by Peter King. London, Financial Times Business Information Ltd, 1984. £120. 147 pp. Reviewer: D.G. Maxwell 2. Mintek reports Report M156 A kinetic study of the reactions of certain gaseous sulphur compounds with iron. Report MI57 Reaction mechanisms in the reduction of Winterveld chrome spinel with graphite and carbon. Report MI72 Computer programmes for the control and datamanipulation of a sequential X-rayfluorescence spectrometer. Report MI77 A proposed test for the determination of the grindabi/ity of fine materials. Report MI86 A survey of the erosion, corrosion, and abrasion of material-handling systems in the mining and mineralprocessing industry. 3. New journal Advanced materials & processes, issued monthly by American Society for Metals (Metals Park, Ohio 44073, U.S.A.). CIM conference The combined 24th Annual Conference of Metallurgists and the 15th Annual Hydrometallurgical Meeting will be held in Vancouver from 18th to 22nd August, 1985. Light metals The 8th International Light Metals Congress will take place from the 22nd to 26th June, 1987. These meetings, which take place traditionally every few years, are organized by the Austrian Metals Industry Association, the Austrian aluminium industry, and the University for Mining and Metallurgy in Leoben, in collaboration with the Aluminium-Zentrale Diisseldorf. President of AS&TS* Mr Arthur Woodington Reynolds (Sam) took office as President of The Associated Scientific and Technical Societies of South Africa on 28th November, 1984. Sam Reynolds was born in Boksburg on 27th December, 1930, and received his education at Christian Brothers College in Boksburg and at St John's College in Johannesburg. World mining Sweden, Finland, and Norway expect representatives of all mining countries in May-June 1987 to the 13th World Mining Congress in Stockholm. The Swedish Mining Association, the Finnish Association of Mining and Metallurgical Engineers, and The Association of Norwegian Mines will organize the Congress, together with the International Organizing Committee of the World Mining Congress. Sheet metal The German Group of the International Deep Drawing Research Group (IDDRG) will be organizing the 14th Biennial Congress of the IDDRG on 21st to 26th April, 1986, in Cologne and Munich. Safety in mines The 21st International Conference of Safety in Mines Research Institutes is to be held in Sydney from 20th to 25th October, 1985. ILAF A conferences The Instituto Latinoamericano del Fierro y el Acero (ILAFA) has scheduled the following congresses for 1985. Mechanical testing of materials The Deutsche Gesellschaft fiir Metallkunde, together with the Deutschen Verband fiir Materialpriifung and the Fachhochschule Osnabriick, is holding a course on the methods used for the mechanical testing of materials at Osnabriick from 9th to 11th September, 1985. Mine ventilation The Second U.S. Mine Ventilation Symposium will be presented from 23rd to 25th September, 1985, in Reno, Nevada, by the University of Nevada-Reno's Mackay School of Mines and Division of Continuing Education.

Jan 1, 1985

By I. Ince, S. Kahraman, M. Rostami, B. Dibavar

The density, porosity, and strength of rocks are fundamental in the design of geo-engineering projects. Determining these properties requires the preparation of smooth core samples, which is usually impossible for soft rocks. Besides, only fragmented samples may be available in some projects. A method for predicting rock properties from rock particles such as drilling debris would therefore be useful. This study was undertaken to develop prediction equations for compressive strength (UCS), tensile strength (BTS), density, and porosity values from the crushability index (CI) obtained from rock fragments. The results showed that UCS, BTS, density, and porosity were strongly correlated with the CI. The physical characteristics and strength of rocks may be predicted with the help of the derived equations. The CI test is a valuable tool for estimating rock properties in drilling projects and in situations where core specimens are not available.

Mar 14, 2024

By A. M. P. Henderson

Twelve members of the Witbank/Middelburg Branch, on a technical excursion, were hosted by the Technical Department, Pinelands site, of AECI on 10th February, 1989. The tour opened with some well-presented talks on 'Permitted Emulsion Explosives', and the application of the 'French' test to the development detonators.

Jan 1, 1989

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran, J. Zoric

A methodology for building pragmatic physics-based models is here adapted to predict the erosion of ladle linings in the steel industry, in order to support operators when deciding whether the lining can be used safely for another heat. A defective lining may allow 140 t of molten steel to spill, with disastrous consequences for workers and plant. The adopted work flow for the development, challenges faced, and some model results are presented. One key learning outcome is that model development should allow time for maturing the process understanding, as well as for many iterations by ‘questions-responses and actions’ at various stages in the model development. Good interaction between the development team and industry case owner is an important success factor. Combining or extending the model with the use of machine learning and cognition-related methods, such as knowledge graphs and self-adaptive algorithms, is discussed.

Apr 16, 2024

By F. Nakhaei, M. Le Roux, Q. P. Campbell, S. Botlhoko

The results of coal sink and float tests are plotted as washability curves. Analysis of these curves indicates the most effective method by which the coal can be cleaned. Sink and float experiments are samplingdependent, destructive, and use toxic chemicals. The present research introduces an alternative method based on a 3D imaging system called RhoVol, in which the density of individual particles is determined from mass and volume measurements. A quantitative error analysis was conducted on coal sample density measurements obtained by RhoVol, and the main factors influencing the errors identified and investigated. The results show that the drawback of this technique is related to its not being able to detect hidden concavities in the particle, resulting in an overestimation of particle volume. Furthermore, it is difficult to capture the impact of porosity and cracks on the volume of coal particles obtained from 3D silhouette images. This mismatch between the RhoVol data and sink and float test results has led to attempts to apply neural network (NN) and linear regression techniques to produce a fully reliable model for correction and estimation of coal density. The NN approach offers superior predictive capability over linear regression, and the estimated density distribution is in line with the sink and float analysis. The root mean square error in estimation of density using the NN model was less than 0.05 g/cm³.

Aug 2, 2022

1. Book reviews Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. (Reviewer: J. Keenan) Separation procedures in inorganic analysis. A practical handbook, by Roland S. Young. Charles Griffin, 1980. £23.00. (Reviewer: R. Murray-Smith) 2. Historical reprints Theinin~rs dictionary, by William Hooson. £14. Discovery of subterraneal treasure, by Gabriel Plattes. £12. Fodinae Regales (The Mines Royal), by Sir John Pettus. 3. De Beers' booklets Amborite - a remarkable new cutting material, by De Beers Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Booklet, 14 pp., free of charge. Natural and synthetic micron powders, by De Becrs Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Leaflet, 5 pp., free of charge. 4. New books Nickel in the environment, edited by J. O. Nriagu. New York, Wiley, 1980.928 pp. $65. Underwater minerals, by D. S. Cronan. London, Academic Press, 1980. 364 pp. $57.50. Data conversion integrated circuits, edited by D. Dooley. New York, Wiley, 1980.298 pp. $26.95 (cloth), $17.50 (paper). 5. NIM reports Report 2057 A mineralogical study of the Rooibokkop- Boschhoek copper deposit in the Marble Hall area. Report 2069 A utomatic setting of the distance between sample and detector in gamma-ray spectroscopy. Report 2070 The prereduction of chromites from the UG-2 Reef. Report 2075 The optimization of some of the conditions for analysis by spark-source mass spectrometry. Report 2082 A survey of the literature on gravity separation.

Jan 1, 1981

By R. Rumpold

The platinum group metals (PGMs) palladium, platinum, and rhodium represent the key materials for automotive exhaust gas treatment. Since there are currently no adequate alternatives, the importance of these metals for the automotive industry is steadily rising. The high value of PGMs in spent catalysts justifies their recycling. The state-of the-art technology is to melt the ceramic carrier and collect the precious fraction in a liquid metal bath. As the feed material has quite high melting points, huge amounts of energy are required for this process. Hydrometallurgical treatments of the spent catalysts offer the possibility to recycle the PGMs with less energy and time demands. Moreover, automotive catalysts contain further valuable materials to improve the exhaust gas treatment. These compounds, like cerium oxide, cannot be recovered in pyrometallurgical processes. This paper deals with a special process that uses hydrometallurgical principles to recycle the valuable metal fraction from spent automotive catalytic converters. Hydrochloric acid in combination with hydrogen peroxide is used as leaching agent. This combination selectively dissolves the PGMs and the cerium, which can be recovered in separate steps. As the leaching solution is regenerated and reused, wastewater generation is minimized. Furthermore, the process residues constitute potential byproducts.

Jan 1, 2012

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

By G. Blight

As part of an investigation of possible water-saving measures at Anglo American Platinum's Mogalakwena Mine in Limpopo, South Africa, a study was made of conditions on the wet beaches of two adjacent tailings dams, each serving a separate plant on the mine. For one of the dams, a special catamaran was designed and constructed to enable the full length of wet beaches to be accessed and sampled immediately after a layer of tailings had been deposited. For the other dam, the wet beach was accessed using conveyor belting and scaffold planks. The length of the beaches was 400 m on the first dam, and 200 m on the second, and each was sampled at 50 m intervals. The parameters reported in this paper, for both beaches, are: > Water content profiles along each beach from the surface to as deep as 2.5 m, at times ranging from 12 hours to 6 weeks from the end of deposition > Particle size distributions at the surface, down the full length of the beaches > Measurements of feed relative density, tonnage and volume, decant and drain flow volumes, as well as rainfall and evaporation for both dams. The surface water contents shortly after deposition have been used to establish the relative density of the settled, decanted tailings and its variation down the beach. This data, combined with the decant and drainage flows, is used to establish the calculated and actual water recoveries from both dams.

Jan 1, 2012

By G. R. Drennan, N. J. Wagner, M. J. T. Sebola

The Soutpansberg Coalfield hosts South Africa's hard coking coal reserves. However, coals in this region are understudied compared to other coalfields in the country. This study characterizes the properties of fine-float fraction samples extracted from a wide diameter borehole core in the Makhado Project, Tshipise sub-basin, Soutpansberg coalfield. Conventional analyses were used to determine the coal quality, petrographic composition, mineralogy, geochemistry (including trace element and rare earth element composition), and free swelling index of samples from six coal horizons and three partings from the economic No.6 Seam. The coal samples are classified as medium rank bituminous C coals (0.88 %RoVmr, 0.92 %Rmax) and are highly vitrinitic in composition (97 vol% mineral matter free (mmf)). The samples show strong caking potential (FSI of 9). The total rare earth concentrations range between 570 and 3193 ppm in the ash samples. Preliminary analysis show all but two samples are promising sources of rare earth elements as the total concentrations exceeded the 1000 ppm cut-off grade. Further research is required to confirm these preliminary findings.

Aug 2, 2022

By N. C. Steenkamp

Lightning has been observed in dust clouds following open-pit blasting. It is proposed that the occurrence of this phenomenon is related to the physical composition and characterization of the mineral fines that comprise the bulk of the dust cloud. Silicate minerals, which are susceptible to fine fracturing during blasting, generate the initial charge. This is further enhanced by collisions and friction during the turbulent upcast in the post-blast dust cloud. Varying size fractions result in different rates at which these particles drop out of suspension and create a secondary temperature gradient. This results in the creation of two charged zones and increases the potential of developing a discharge in the form of lightning. The ideal prevailing meteorological conditions need to be windless to minimize the effect of particle dissipation and have sufficient moisture toenhance the potential of generating lightning.

Apr 14, 2024

By A. M. Bauristhene

Ti-64, which accounts for more than 50% of the worldwide titanium tonnage, has found commercial importance in industries requiring components with high specific strength and resistance to corrosion. Investment casting is the preferred production method due to the difficult machinability of the alloy. This study was aimed at investigating the mechanism and the extent of alpha case formation on Ti-64 components cast using the investment casting method with YFSZ (yttria fully-stabilized zirconia) shell moulds after vacuum induction melting. The extent of the reaction between the mould hot face and the molten metal has been studied by varying parameters such as soaking temperature and mould hot face composition, and examining their effects on the reaction with the mould. An increase in the soaking temperature had an effect on the alpha case, both in appearance and hardness, but had no effect on contamination levels by carbon, oxygen, and nitrogen. The depth of alpha case increased with soaking temperature, increasing from 35 µm to 161 µm with an increase in temperature from 1200°C to 1400°C. The micro-hardness profiles provided insight into the effect of the alpha case on the mechanical properties of the Ti-64 alloy by displaying hardness values of 1000 HV0.1 and above, but could not be solely utilized to determine the alpha case penetration depth due to microstructural differences in the unaffected Ti-64, in particular the martensitic microstructure that formed with a fast cooling rate from a higher temperature. Levels of expected contaminants such as Zr, Y, 0, and C were low. The addition of the colloidal zirconia binder affected the interfacial reactions. YFSZ proved to be a thermodynamically stable refractory material, with the alpha case possibly forming as a result of segregation.

Jan 1, 2013

The development of short- and medium-term mine production schedules in isolation from each other has meant that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution, however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and medium-term activities simultaneously. This paper addresses the task of integrating short- and medium-term production plans by combining the short-term objective of minimizing deviation from targeted mill feed grade with the medium-term objective of maximizing net present value (NPV) into a single mathematical optimization model. A conceptual sublevel stoping operation comprising 30 stopes is used for trialling segregated and integrated scheduling approaches. Segregated medium- and short-term scheduling using separate models achieved an NPV of $42 654 456. The final scheduling approach involved integrating the two scheduling horizons using the newly-developed globally optimal integrated production scheduling model to achieve an NPV of $42 823 657 with smoother mill feed grade. The larger the stope data set, the larger the difference between the two scheduling approaches is likely to be. At the very least, an integrated approach ensures feasibility across the two scheduling horizons, which cannot always be assumed when using a segregated approach.

Jan 1, 2012

By H. E. James

During the past ten years there has been an upsurge of interest in the development of selective ion exchange resins and solvents, and of ion-exchange and solvent extraction equipment tailored to the special requirements of mineral-processing circuits. It is therefore not surprising that the recent Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, held at the National Institute for Metallurgy (NIM) on 7th and 8th February, 1980, was a resounding success. This Symposium, organized jointly by NIM. Ion exchange and solvent extraction The Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, which was organized jointly by the National Institute for Metallurgy, the South African Institution of Chemical Engineers, and the South African Institute of Mining and Metallurgy, was held in Randburg on 7th and 8th February, 1980. Analytical chemistry The Fifth International Conference on Analytical Chemistry, organized by the Chemical Society, is to be held at Lancaster University, England, from 20th to 26th July, 1980. Coal mining The First International Symposium on Thick and Steep Seam Coal Mining will be held in London from 18th to 21st May, 1980. Mineral processing The XIV International Mineral Processing Congress will be held in Toronto from 10th to 16th October, 1982. The theme of the congress will be 'Worldwide industrial application of mineral processing technology'. Sessions will be held on the following:

Jan 1, 1980

By M. A. Reuter, N. J. Bartie

Metals make modern societies function, and increasingly, various high purity precious and special metals endow sustainability-driving technologies with specific functionalities. These metals become heavily intertwined within products, complicating end-of-life treatment. To counteract the resulting downcycling and potential depletion of scarce resources, maximising both the quantities and qualities of materials recovered during primary extraction and recycling, processes should be a priority in the pursuit of sustainable circular economy. Adopting a process simulation approach; a digital twin for the life cycle of cadmium-telluride solar photovoltaic (CdTe PV) modules was created. The system comprises an integrated metallurgical production system that produces, among others, cadmium, tellurium, selenium, zinc, copper, and lead, all of which are required to manufacture PV modules. System-wide resource efficiency and environmental impacts are assessed using exergy analysis and life cycle assessment, respectively. Simulation of this large and complex product life cycle at a high level of detail allows for the evaluation of potential system-wide effects of various production, recycling and residue exchange scenarios aimed at maximising the sustainability of the entire system. It diminishes the need to make arbitrary choices about allocation methods for the distribution of environmental impacts in multipleoutput production systems. Furthermore, it demonstrates the key importance of metallurgy in achieving circular economy. Keywords: Circular economy, sustainability, simulation, metallurgy, CdTe photovoltaics, life cycle assessment

Jan 1, 2020