Search Documents

By H. Kenneth Sacks

The Bureau of Mines has developed hardware for electromagnetic (EM) detection and location of miners trapped in underground coal mines. This report describes a technique for using the developed equipment for locating uncased boreholes underground. Results of several field and laboratory experiments are described.

Jan 1, 1978

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By Harry Dobroski, Larry G. Stolarczyk

A medium-frequency (MF) communication system has been built and has been tested in underground mines. It provides radio coverage to vehicles and personnel anywhere in the mine via parasitic coupling into existing mine conductors. The system consists of base stations, repeaters, and vehicular and personnel transceivers. Air-core antennas for vehicles and clamp-on antennas for base stations and repeaters were designed for maximum coupling efficiency using existing mine wiring. Personnel transceivers are of a unique vest design that features a low physical profile, good user comfort, and efficient antenna design. In-mine tests show impressive results. Range between rubber-tired vehicles and base stations is often measured in miles. With repeaters, greater range is possible.

By John Owens, Wayne Howie, Hamid Maleki

After an analysis of the hazards of room-and-pillar retreat mining systems, it became apparent that safety could be significantly improved by considerations of (1) human factors, (2) remotely controlled mobile roof supports (MRS=s), (3) mine layout designs, and (4) ground monitoring systems. Initial studies of the effectiveness of MRS=s focused on their interaction with mine strata and evaluations of suitable measurements for detecting roof stability problems during pillar extraction. These studies indicated that overall stress distributions and strata movement were most influenced by the stiffness of coal-measure rocks and the design of mining layouts. Thus, to improve worker safety, mine layouts should be carefully designed and a pillar extraction method chosen for specific geologic and stress conditions. Pillar failure was often associated with an increase in pressure on the hydraulic gauges of the MRS, and roof failure was often preceded by rapid changes in the rate of roof-floor convergence. These studies led to development of a monitoring system that displays loading rate on an MRS in real time. A major MRS manufacturer cooperated in installing and testing the system on an MRS. New field studies focus on evaluating the performance of the system, measuring roof-floor convergence, and optimizing the safety of MRS operations through proper mine layout design.

By George S. Koch

In preparing diamond-drill core samples for assay at the Homestake mine, Lead, S. Dak., 5-foot intervals of core are processed through three stages, crushing, grinding, and pulverizing, and portions of the core material are discarded after splitting at each stage of preparation. Then two 1-assay-ton fractions are taken from the pulverized material and assayed. This report investigates alternative methods of sample preparation. The consequences of crushing, grinding, and pulverizing all rather than part of the core are appraised through the statistical analysis of assay results from 118 5-foot intervals of core. Evidently, a substantial improvement in precision at small additional expense is obtained by grinding most or all of the core before splitting. Pulverizing all of the core would be desirable only if doing-so would cost less than assaying five random splits from each interval. Graphs and tables detail appropriate procedures to obtain specified precisions. The experimental design and methods can be applied to similar problems in preparing core and other geological samples.

Jan 1, 1972

By C. M. Mason

Mechanical mining produces large quantities of very fine coal dust called float dust. The associated increase in hazard requires a reexamination of the Bureau of Mines method of evaluating the incendivity of explosives in coal dust-gas-air mixtures. A technique recently developed by Bureau of Mines laboratories for evaluating the incendivity of explosives in coal dust-air mixtures was applied, with modifications, to coal dust-air-natural gas mixtures. A series of permissible explosives were evaluated by this modified technique. Results indicate that the modified technique could be the basis of a more discriminatory procedure than that presently in use.

Jan 1, 1968

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

Provide the U.S. mining industry with the means to measure and control exhaust emissions of diesel engines used in underground mines. Approach Diesel research is divided into four primary areas: exhaust aerosol measurement, particulate control, gaseous emission control, and chemical and biological characterizition of particulate matter. Diesel research is frequently cosponsored by industry; collaborative research ventures between industry, academia, other government agencies, and the Bureau arc common. Diesel research at the Bureau is conducted in the diesel engine research facility at the Bureau?s Twin Cities Research Center (TCRC). This facility is a state-of-the-art laboratory capable of performing emissions testing, exhaust control evaluations, and safety tests. Background Exposure of mine workers to airborne contaminants from diesel engine exhaust is potentially harmful. The National Institute for Occupational Safety and Health has recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen" and that ?reductions in exposure to diesel exhaust in the workplace would reduce the risk." The U.S. Mine Safely and Health Administration (MSHA) convened an Advisory Committee on Standards and Regulations for Diesel-Powered Equipment and is beginning to implement its recommendations, which cover health, safety, and certification and approval issues surrounding the use of diesels underground. In January 1992, MSHA published an advance notice of proposed rulemaking to regulate diesel particulate matter in underground mines.

Jan 1, 1992

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

As the use of deep -rut mining increases, there - expected to be a greater demand for methane (CH,) measurement devices capable of scanning working faces al depths in excess of 10 m to alert mine personnel of hazardous concentrations of CH and to satisfy regulatory requirements. Remote optical devices offer the most promise to satisfy these objectives while the operator remains safely under supported roof. A second¬-generation remote Optical methanomeor (ROM) bas been designed and Is undergoing laboratory evaluation at the National Institute for Occupational Safety and Health. It operates on the principle of differential absorption of the "u;' fundamental absorption band of CH, centered at 3.31 um in the infrared region of the spectrum. The new instrument differs from the previous prototypes by the replacement of the two hand pass differential absorption technique of measurement with a single filter gas correlation technique and a refinement of the amplifier and gating circuitry used within the unit. This results in a more accurate isolation of the CH, spectral absorption band centered at 3.31 um. A specially designed 0.4m-diam variable-length gas mixing tunnel was constructed and instrumented with CH4 sampling capability to calibrate the ROM. Experiments have demonstrated the ability of the detector to respond to various conditions of CH, (pn•m) at distances as great as 12 m. Thermal radiation generated within the instrument is the controlling factor in the drift of the output signal nod, therefore the reliability of the instrument. Several approaches to reduce this extraneous radiation interfering moth the infrared detector, described, such as the installation of a fan in the instrument and thermoelectric coolers on the detector's beat sink. Implementation of this technology will significantly improve the safely of miners.

Jan 5, 1997

By A. L. Engel

This report describes laboratory-scale experimental treatment of six base-metal ore samples taken by engineers of the Bureau of Mines, Region II, while investigating ore deposits in California and Nevada. The information is of interest in developing the mining districts represented or when similar ores from other sources are being studied. Simple treatment methods were employed as far as possible. More complex treatments also were tried when necessary. The possibilities and limitations of the methods applied to the several ores are shown by the data herein reported.

Jan 1, 1960

Reduce the noise radiated by the auger miner cutting head (typically 105 dBA at the face) by 10 dBA without compromising the durability or productivity of the tool. Approach Research was conducted by the Bureau of Mines to identify the noise sources of auger miners with emphasis on the cutting head and coal cutting process. The overall noise level generated by the coal cutting process was found to depend greatly upon the structural characteristics of the auger cutting head. Based on this information, a quieter cutting head was

Jan 1, 1982

In the past, mine management has been concerned with removing water from active mining sections primarily because it hampered the movement of mining equipment and aggravated the working condition of the miners. Pumping water to sumps and gravity drainage by ditching have proven successful in mines for minimizing section down time due to water influx. However, with the advent of more strict pollution laws the mining engineer must now be concerned with keeping water out of the section and also with preventing it from causing pollution. A review of the handbooks and textbooks used in the mining engineering curricula reveals that little has been written concerning acid mine water prevention or control in underground coal mines. Additionally, the review of the curricula of mining schools indicates they are not teaching the engineering students the necessary techniques of mine water management as they relate to the abatement of mine water pollution.

Jan 1, 1970

By D. R. Tesarik, R. W. McKibbin, J. B. Seymour

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars),and biaxial stress meters (to measure stress changes in several support pillars and abutments). Two- and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 1995

By Joseph B. Huvos

Said to be one of the world's most under-developed countries, Benin had a gross national product (GNP) estimated at $1 billion in 1980.2 Contribution of the mineral industry such as cement and limestone to the GNP was negligible, but exploration of mineral potential continued Minerals.-The United Nations Development Program (UNDP) conducted an investigation of three deposits from 1977 to 1980: Phosphates (Mekrou), gold (Perma), and chromite (Buem). A phosphate rock deposit containing about 4.5 million tons recover- able by opencast techniques was discovered. It was not known if the gold and chromite deposits were recoverable economically. Iron ore deposits of some 230 million tons near Loumbo-Loumbo are at present not exploitable because of lack of infrastructure in the northern part of the country. Geologic mapping with British and French assistance was also pursued in 1980.

Jan 1, 1982

By Richard H. Singleton

Native asphalt was produced in 1980 by six companies in four States. Leading States were Texas and Utah. Output decreased 22% in 1980 to 1.25 million tons while value decreased 2% to $25.0 million. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert, Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. The product was used mainly in street and road repair. Gilsonite was produced by American Gilsonite Co. in Uinta County, Utah, and by Ziegler Chemical and Mineral Corp. in Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1981

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By Lloyd A. Morley, Robert Stefanko

1 Abaibanel, S , "Deflection of Confining Walls by Explosive Loads," Israel Jour. Technology, vol. 4, n. 1, Feb 1966. 2 Albertoni, S and others, "Numerical Computation Methods for Implosion Processes," EURATOM Proc. of the Conf. on Megagauss Magnetic Field Generation by Explosives and Related Experiments, Milan (Italy), July, 1966. 3 Alexander, S. J , and Hambly, E. C., "Design of Structures to Withstand Gaseous Explosions," Concrete, vol. 4, n 2, Feb. and March, 1970. 4 Anonymous (Belgium Institute of Extractive Industries), "Report for 1968 (covering approved equipment for Belgiums gassy coal mines)," (in French and Flemish), Amales des Mines de Belgigue, n. 6, June, 1969. 5. Anonymous (Ghent Univ., Belgium), "The Welding of Very Thick Steels. Margin of Uncertainty of the Robertson Test," EURATOM Contract 042-61-9-RDB, May 20, 1965. 6. Anonymous, "Inportance of the Nature and Size of Weld Defects with Regard to the Mechanical Strength of Pressure Vessels, (in Flemish), A. Sys. Rev. Soudure, vol. 27, n. 3, 1971. 7. Anonymous (Raentgen Technische Dienst N V., Rotterdam), "Non¬Destructive Welding," Quarterly Report No 13, EURAEC - 1342, March 30, 1965. 8. Anonymous (Staff, USBM Safety Research Center), "Research and Technologic Work on Explosives, Explosions, and Flames: Fiscal year 1969," USBM IC8492, 1970. 9. Anonymous, "Symposium on Flameproofing Intrinsic Safety and Other Safeguards in Electrical Instrument Practice, April 27, 1962," IEEE Conf. Report Ser. 3, 1963. 10. Anonymous, "Unfired Pressure Vessels," ASME Pressure Vessel Code, Sec. 8, 1965. 11. Anonymous, "Unusual Pressure Relief Devices," Industrial and Engineering Chemistry, vol 54, n. 1, Jan., 1962. 12. Archer, G. L., "Design to Avoid Brittle Fracture in Welded Structures," Paper No. 4, Improving Welded Prod Design, vol. 1, Welding Inst., Cambridge, England, 1971. 13. Bailey, F. C., "Buckling and Failure Strength of Plating Panels Loaded in Shear," Final Report NASA Contract NObs-72290, Lessels and Assoc., Inc., Waltham, Mass., Sept. 20, 1963.

Jan 1, 1974

By David F. Smith, F. A. Hartgen

"Incidental to a cooperative investigation with the Carnegie Institute of Technology and the International Combustion Engineering Corporation on the burning characteristics of a powdered coal and the powdered semi-coke therefrom, the U. S. Bureau of :alas has determined the relative temperatures at which rapid self-heating occurs in these two fuels. Determinations were made on various screen sizes of the two fuels. Chemical analyses on different sizes were made in the bureau's Coal Analysis Laboratory, of which H. M. Cooper is in charge. The true densities were determined b the method given in Bureau of Mines Technical Paper 8.4The apparatus used in the determination of the temperatures for rapid self-heating was similar to that used by Wheeler A 10-gram sample of the fuel was placed upon a screen in a glass tube enclosed in a vertical electric furnace. The tube was surrounded with sand. One thermocouple -as imbedded in the sand and another in the fuel. Measurements of the temperatures were obtained at regular intervals with a recording potentiometer, as the furnace temperature was uniformly raised. Dry air was passed down through the fuel samples at a uniform rate of 123 c. c. per minute; the temperature of the air was substantially that of the furnace."

Oct 1, 1929

By Peter F. Strong, Robert L. Lagace, Alfred G. Exslie

The theoretical study of WF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer is the concern of this paper. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. The theoretical results are compared with published measurements. This work was part of an investigation of new ways to reach and extend two-way communications to the key individuals who are highly mobile within the sections and haulageways of coal mines.

Nov 14, 1974

By Roberta L. Hudak, Ellsworth R. Spencer, Eric R. Bauer, Adam K. Smith

The National Institute for Occupational Safety and Health (NIOSH) is conducting research with the objective of preventing hearing loss in the mining industry. Longwall mining is one sector that has received considerable attention. Studies involving the monitoring of worker noise exposures, characterizing equipment sound levels and dominant noise sources, evaluating engineering noise controls, analyzing hearing protection device (HPD) effectiveness, and testing of improved sound level monitoring techniques specifically for longwall mining systems, are being conducted. The research efforts revealed that stageloader operators are the most exposed longwall workers, with the discharge end being the noisiest location along the stageloader. In addition, the studies have shown that using stationary dosimeters, coupled with observational data of the cutting cycle and worker habits, has the potential for improved monitoring of the effectiveness of engineering noise controls. To address the ineffective use of soft foam earplugs, a simplified 3-step method was developed for inserting soft foam earplugs. Results indicate a 9 dB greater attenuation after training subjects on the 3-step method. Finally, muff type HPDs are being evaluated for effects of speech intelligibility in noise. The combined results of these studies illustrates that much can and has been done to prevent noise-induced hearing loss (NIHL) in the mining industry, especially with respect to longwall mining workers. This paper presents an overview of ongoing studies, a progress report of results, and the implications for reducing worker noise exposures and preventing NIHL in longwall mining workers.