Search Documents

By A. R. Rule

This report describes preliminary studies by the Bureau of Mines to develop a procedure for extracting the fluorine from low-grade fluorspar ores in which the CaF2 particles are finely locked in the calcite matrix. A combination of flotation beneficiation and pyrohydrolysis is applied to recover and to liberate the fluorine. Flotation of a finely locked high-calcite fluorspar ore containing only 11.7 pct CaF2 recovered over 92 pct of the fluorspar at a grade of 51 to 52 pct CaF2. Pyrohydrolysis of the flotation concentrate liberated nearly 90 pct of the fluorine as aqueous HF. By this procedure over 80 pct of the fluorine contained in the original ore was extracted.

Jan 1, 1974

By C. H. Elder

An experimental degasification program using a vertical borehole and vacuum pump to drain gas from the gob area of a longwall panel was successful at Bethlehem Mines Corporation, Cambria Division, No. 33 coal mine. Sixty-one million cubic feet of methane has been exhausted during a 9-month period. Daily production time in the panel increased as a result of lower methane levels in the returns. Removal of large quantities of methane in this way and the exclusion of it from the ventilating system will provide reduced cost in mine ventilation and provide a safer environment for the mine.

May 1, 1969

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962

By John C. Ferm

This report contains a summary of Phase I and complete results of Phase II portions of a study of geologic factors associated with roof falls in mines on the Pocahontas #3 coal seam in southern West Virginia and southwestern Virginia. Principal objectives of Phase I was the selection of five mines that best portrayed the spectrum of roof and mining conditions and Phase II consisted of a measurement and documentation program for each of the five mines. The documentation measurement program included reconnaissance mapping, detailed mapping, joint measurements and coring roof rock. 1.2 PHASE I RESULTS The results of Phase I consisted of the selection of the following five mines for detailed study: Virginia Pocahontas #3 (Island Creek Coal Company), Bishop (Consolidation Coal Company), Shannon Branch (Allied Chemical Company), Keystone II (Eastern Associated Coal Company) and Macalpine-East Gulf (Westmorelenad Coal Company). In addition, Phase I results, which were based on questionnaire data, indicated that the kind of rock in the roof --gray sandstone, crystallized sandstone, laminated sandstone and shale, grey shale, slickensided shale, and rider seams could be associated with good and bad top areas. Also presence of vertical separations, bolt length, entry and cross-cut width, length and torque on bolts and depth of overburden seemed to be related factors. These data provided a focus for the Phase II measurement program.

Jan 1, 1975

By D. Z. Hobbs

Because an economic method for preparing pure boron has not been developed, a program was started by the Bureau of Mines to evaluate existing techniques or to develop new methods for preparing the pure element. This report describes investigations directed toward the development of techniques for the preparation of pure boron by fused-salt electrolysis. Only two of the several fused-salt baths tested were satisfactory for the preparation of boron. These baths contained (1) potassium fluoride, lithium fluoride, potassium fluoborate and boron trioxide; and (2) potassium fluoride, potassium chloride, and boron trioxide. Of these two mixtures, the latter was more satisfactory. Elemental boron of from 90- to 95-percent purity and, in isolated cases, as high as 98-percent purity, was prepared from these two types of fused-salt baths. There appeared to be no distinct differences either in the yields or the purity of boron prepared at current densities ranging from 795 to 1,000 amperes per square foot. Current efficiencies were as high as 85 percent.

Jan 1, 1961

By R. O. Dannenberg

Applicability of the fluosilicate sintering process to recovering beryllium from beryl-spodumene concentrate analyzing 1.4 to 3.7 percent BeO (10 to 30 percent beryl) was investigated. The work was one phase of a Bureau of Mines research program undertaken to assess applicability of conventional processes and to devise new procedures for treating various potential beryllium feed materials. Beryllium recovery of about 70 percent in a product of 99-percent BeO grade was achieved in treating 3D-percent beryl concentrate. The process consisted of (1) sintering a briquetted charge of concentrate, soda ash, and sodium fluosilicate for 3 hours at 750° C.; (2) extracting the soluble beryllium by multiple stages of water leaching; (3) adding caustic to the leach solution and boiling to hydrolyze and precipitate crude beryllium hydroxide; (4) dissolving the crude beryllium hydroxide in sulfuric acid and separating the solution from undissolved silica; (5) sulfidizing the acid beryllium solution to precipitate heavy metal impurities; (6) adding ammonia to the clarified sulfate solution to precipitate beryllium hydroxide; and (7) converting the hydroxide to beryllium oxide (beryllia) by calcining at 900° C. About 60 percent more sodium fluoSilicate was required per unit of beryl than is used industrially in treating 10-to 12-percent BeO concentrate (80 to 90 percent beryl). Recovery decreased, and flux requirements increased, when treating concentrates containing less beryl.

Jan 1, 1963

By C. E. Reistle

[In producing crude oils of paraffin base and of mixed base the producer is often confronted with the problem of preventing and removing paraffin that settles out of oil and accumulates in the well. This paraffin consists of heavy waxes with some sand and asphalt, and varies in. consistency from a soft semifluid wax to hard gummy wax. This problem is by no means a new one as troubles have been encountered with it since the earliest days of the industry. However, with the discovery of the panhandle, Texas, field and other large fields in which extensive troubles have been encountered, the problem has assumed added importance. In new fields the most serious trouble with paraffin is in the flowing wells the paraffin accumulates in the casing and tubing of such wells and unless removed will completely plug the well. This condition also develops in wells which are produced by gas lift, and often presents a serious problem when, this method of producing the oil is used. In older fields paraffin is also deposited on the face of the producing sand that on the walls of the hale or within the interstices of the sand near the hole, and this materially affects the amount of oil that can enter the well.]

Jan 1, 1927

By L. B. Berger

"INTRODUCTION Accurate determination of carbon monoxide in concentrations ranging from 0.2 to about 0.5 percent by volume is troublesome, because such concentrations are too high for some analytical methods and too low for others. Methods that are sensitive to concentrations of carbon monoxide considerably less than 0.2 percent are approaching their upper limit of usefulness when applied to the analysis of samples containing 0.2 percent or more of carbon monoxide, and it may be necessary to resort to dilution of the sample with a known proportion of air, or otherwise modifying the analytical technique, to obtain satisfactory results. Such methods include the determination of carbon monoxide by reduction of heated iodine pentoxide 3/4/5/ by the ""Pyrotannic acid"" method 6/ and by the so-called ""phosphomolybdic acid"" method. 7/ The use of conventional gas-analysis equipment, such as the Orsat type, in the determination of carbon monoxide in concentrations ranging from 0.2 to 0.5 percent is not desirable, as possible analytical errors may be of about the same magnitude, thus producing results of little quantitative value.For several years prior to this publication, the Gas Analysis Laboratory of the Health Division of the Bureau of Mines has used a modification of the Haldane type 8/9/10/ gas-analysis apparatus for the determination, by absorption in a chemical reagent, of carbon monoxide in low concentrations that are not readily determined by other methods. The method is applicable also to the determination of higher concentrations. As the procedure has proved successful and has been adopted by others, this report was prepared to describe the method and to present results of analyses obtained with it."

Nov 1, 1947

By T. T. Read

"Education is the one thing which is unanimously regarded as valuable. The growing complexity of modern life, with its intricate organization, the manifold kinds of mechanical equipment that are used, and the constantly growing, necessity for the speedy and accurate interchange of information and ideas, make education an asset that constantly increases in value. The number of things that may profitably be known has grown so large that the field of education has been divided, and attention is often directed to only those things that are most immediately valuable. Modern educational facilities are often directed to what may be called corrective, work; the, providing of people with information that they teed in the conduct of their daily lives, but which for various reasons they have not previously had facilities for acquiring. The value of special education in the industrial world has been so thoroughly demonstrated that far-seeing managers of mining enterprises are always interested in the educational facilities existing in the community where their work is carried on.The educational facilities of a modern community may be classified in several ways. They may be divided into;1. Facilities for general education, for the purpose of increasing the whole field of knowledge of the student.2. Facilities for special education, which are intended to remedy a specific defect, or to give proficiency in some special field. This may be divided as follows;a. Training for work, intended to fit an employee to adequately perform the task assigned to him, this ranges from brief instruction by a foreman or fellow-worker up to definite training courses in which the employee dose nothing but study for a period of several weeks or months, being paid during this period a wage that may range from a nominal amount up to practically full time salary. The student's educational preparation may already be fairly advanced. Some of the manufacturers of electric machinery maintain, a school similar to that just described for graduates of engineering colleges. In other cases the only pre-requisite may be a common school education, as in the schools for operators, maintained by the telephone companies."

Apr 1, 1920

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By James P. Bennett

To improve construction materials for emerging chemical and metallurgical technologies, the Bureau of Mines is investigating the acid resistance of ceramic materials. In the study described here, eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed to 20 wt-pct HC1 at 50° C for 110 days. The test apparatus designed to evaluate the materials is described. Changes in chemical and mineralogical composition, cold crushing strength, volume, and weight, and leach rates of AI, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. In general, the statistically significant physical property changes that occurred were small. In many cases, no changes were detected.

Jan 1, 1982

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

By T. G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a porphyry copper sulfide ore. The purpose was to determine the effects on copper leaching of additions of NaCI to a conventional sulfate leach system and to analyze the oxidant requirements and the oxidation products that resulted from leaching of the sulfide minerals in the ore. Baseline sulfate and sulfate plus 2-pct-NaCl-leach-solution experiments employing 167-kg (367-lb) and 152-kg (333-lb) charges, respectively, were conducted. The minus 25.4-cm (10-inch) ore was leached at 90° C under flooded conditions with 2.8 MPa (400 psig) of oxygen bubbling through the system. Sixty-seven pct of the copper was extracted in 1,236 days of leaching in the NaCI experiment, whereas 47 pct of the copper was extracted in 913 days of leaching in the baseline experiment. Diffusion into and out of the ore fragments controlled the rate of leaching, which precluded enhancement of the leach rate by the chloride ions. The calculated oxygen consumption was 3.17 kg/kg of copper extracted in the baseline experiment and 3.46 kg/kg of copper extracted in the experiment to determine the effect of chloride ions.

Jan 1, 1982

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962

By H. H. Fields, Stephen Krickovic, M. G. Zabetakis, Albert Sainato

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot -deep vertical borehole. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the corresponding values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By A. R. Elliott

"In addition to the usual interpretation that is placed on the words ""thief"" and ""thieves"", the petroleum industry also uses these words when referring to an instrument that is used for taking samples of oil from a tank or reservoir. It is an abbreviation of the term ""thief-tube"". It is desirable in sampling volumes of oil in tanks or reservoirs to obtain samples at different intervals below the surface of the fluid, because of the variation in the character of the oil at different depths. It is for this purpose that the ""thief"" is used.The subject of oil thieves is probably as old as the oil industry itself. Opinions as to which is the most practical instrument for thieving oil in tanks, to obtain a true average sample, differ wherever oil is produced and is analyzed. Every district, and even many of the companies within the district, will have different appliances for ""grabbing"" oil samples. It is interesting to note in passing that though the thief has an apparently insignificant part in the handling of oil, yet the results depending on it are of paramount importance practically every branch of the transportation, refining, and marketing of petroleum. Determinations, particularly dependent on a representative sample, are made by the centrifuge, laboratory distillation tests, and the hydrometer.The purpose of this article is to discuss conditions found in the California fields. Only a general description of types of thieves and the methods of using them will be given. However, it is believed sufficient data are given to enable the reader to form his own opinion as to which of the devices is most practicable under the prevailing conditions. Thieves of all types have their good points, speaking broadly, and it is possible to get good results with any of them, provided they are operated according to instructions and with due care. In work of this kind the advantages or disadvantages reside in the person operating the instrument rather than in the instrument used."

Apr 1, 1920

By David E. Emerson

The Bureau of Mines has developed a mass spectrometer method for deter-mining the helium-3 content of high-purity helium. The work was performed to evaluate experimental methods for removing helium-3 from high-purity helium and to better determine the composition of pure helium used in research. This was accomplished by increasing the inlet sample pressure, ionizing current, and amplification of the current produced by the ions collected on a conventional mass spectrometer that had been modified. With these modifications, the helium-3 content was determined in the parts-per-million and parts-per-billion range in helium-4.

Jan 1, 1976