Search Documents

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By R. L. Stein

For the past several years, the Bureau of Mines has been actively engaged in developing two new oxygen self-rescuers through research contracts with private industry. These new oxygen self-rescuers are designed to be carried by a miner while he is at work and are used during emergency escape, supplying high-purity oxygen to the user and, at the same time, absorbing carbon dioxide (C02), The first of the two new self-rescue breathing devices is a 10-minute, self-contained apparatus developed by the Mine Safety Appliance Co, Size and weight of the unit are comparable to the currently used self-rescue devices. The second device, designed and developed by Lockheed Missiles and Space Corp., is 8. 4.5-lb package which supplies 1 hour of oxygen to the miner. Both devices have a canister which contains the oxygen-producing and CO2-absorbing potassium superoxide chemical, a breathing bag, a bite-type mouthpiece, noseclip, goggles, and hoses connecting the canister and mouthpiece. When needed in an emergency, the miner removes the outer protective cover and dons the unit. For both devices oxygen is immediately available once the mouthpiece is placed in the mouth. These two new units have received prototype approval from the National Institute for Occupation and Safety Health (NIOSH) and the Mining Enforcement and Safety Administration (MESA).

Jan 1, 1976

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,040 Bcf as of January 1, 1987. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 265 Bcf, (2) helium in probable natural gas resources, estimated at 228 Bcf, (3) helium in possible natural gas resources, estimated to be 320 Bcf, and (4) helium in speculative natural gas resources, 227 Bcf. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a separate classification. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 951 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 53 Bef. There is 36 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1988

By M. D. Marshall

This handbook is for the engineer or person responsible for the storage and removal of material from bins and silos in the minerals industry. The objective of the handbook is to prevent bin-related accidents by eliminating problems which require workers to enter bins. It provides basic information on handling materials so that knowledgeable decisions can be made on bin design and accessories to minimize flow stoppages. Materials are classified in terms of their flowability, and bin design and accessories suggested for each classification. A method for classifying a material is also given, and the various types of material flow aids reviewed. Safety around bins is the basic theme of the handbook. Federal regulations are reviewed and additional suggestions presented to prevent bin accidents. New equipment for releasing material hang-ups is reviewed.

Jan 1, 1984

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By Dale E. Wittmer

Nonoxide ceramic materials could substitute for high-temperature alloy steels containing imported critical and strategic materials such as cobalt, chromium, and nickel if their high-temperature properties can be improved. An important result of this substitution would be a reduction of the Nation&apos;s need for imports of critical and strategic materials. In this Bureau of Mines investigation, the primary objective was to produce high-purity u1trafine (particles <5 ~m equivalent spherical diameter (ESD)) alpha-silicon carbide (a-SiC) powders with improved high-temperature properties using the Bureau&apos;s patented turbo-milling process. A secondary objective was to determine the feasibility of using polymer mill construction materials as a means of eliminating metal contamination from the turbomill. U1trafine a-SiC powders with BET (Brunauer-Emmett-Te11er) surface areas from 30 to 35 m2/g (~0.06 ~m particle ESD) were produced in an all-polymer turbomi11. These high-purity powders (with I-pct Band I-pct C additions) hot-pressed to greater than 99 pct of their optimal density and exhibited properties commensurate with those of commercially available a-SiC. The most promising of the construction materials tested for the major wear surfaces of the turbomi11 was u1trahigh-mo1ecu1ar-weight (UHMW) polyethylene, a polymer thermoplastic.

Jan 1, 1984

By Nicholas P. Kripakov

The U.S. Bureau of Mines examined the applicability of existing material models to solve practical geotechnical mining-related problems by solving a yielding pillar stability problem considering confining effects on strength. Numerical difficulties normally encountered with modeling strain softening behavior were eased with a simplified computational procedure using a quasi-elastic approach to account for residual strength after initial failure. Although in agreement with a confined-core pillar design method using actual mine conditions that include mine layout geometry, overburden geology, and rock properties of the deposit and surrounding structure, the results cannot be verified because measured field data are not available at this writing.

Jan 1, 1981

By Ludwig Schmidt

[The use of vapor-tight tanks has proved so effective in reducing the evaporation losses of petroleum that today practically all operators are using this typo of equipment. It has boon shown, however, that vapor-tight tanks should be supplemented with additional measures which will further reduce evaporation. Probably the most effective use of the supplemental measures are found on the small producing leases where the breathing losses from vapor-tight stock tanks materially affect the volume and gravity of the stored oil. The breathing loss from a vapor-tight stock tank that is filled and emptied daily is a negligible quantity. Also, the filling loss, which on the average varies between 0.1 and 0.2 per cent, usually is not of a sufficient quantity to affect materially the value of the crude. However, the combined breathing and filling losses from a vapor-tight tank requiring several days to fill are of sufficient importance to warrant the use of measures in addition to the vapor-tight tanks. The breathing losses are caused by atmospheric variations. Probably the greatest are the changes in atmospheric temperature which cause changes in temperature of the vapors in the tank. During the day, as the temperature increases, the gasoline-saturated vapors in the tank expand and are forced out into the atmosphere. At night the vapors are cooled and contract, drawing into the tank fresh air, which becomes saturated with gasoline vapor and is forced out of the tank during the following day. In Addition to the maximum and minimums temperature variations there are many smaller variations throughout a twenty-four period caused by showers, clouds, winds, and other atmospheric conditions which likewise cause the tank to breathe. The two mist common measures used by lease operators for reducing breathing losses in vapor-tight tanks are, first, operating; lease tanks under pressure, and second, the use of light colored paints anti tank houses. In this report these two methods are discussed together with their adaptability to lease operation. Results of experimental observations are given which show the reduction of evaporation looses where these supplemental measures have been used.]

Jan 1, 1927

By Herbert H. Fields

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (1), and pipeline--quality gas was introduced into a commercial pipe-line. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed,

Jan 1, 1975

By V. A. Marple, K. L. Rubow

"4.1 IntroductionIn previous chapters impactors have been described as useful instruments for classifying particles by their aerodynamic diameters and for measuring particle size distributions. These impactors can be used most reliably if the user has some understanding as to how the impactor classifies particles and what parameters are important in this classification process. This understanding can best be obtained by a theoretical inspection of inertial principles.This chapter reviews the most recent theoretical impactor work and the latest theoretical efficiency curves. Procedures are then given for using these efficiency curves in the design and evaluation of cascade impactors. Finally, several examples are given comparing theoretical and experimental efficiency curves, pointing out when the theory can be used with great confidence and when the theory should be used only as a guideline.Due to the rather simple principle of operation of an inertial impactor (i.e., the impingement of a jet of particle-laden air on a flat plate) the impactor readily lends itself to theoretical analysis. Three notable works in the early 1950,s were those of Davies and Aylward (1951), Davies et al. (1951), and Ranz and Wong (1952).Davies and Aylward (1951) used a method of conformal mapping to obtain an analytical solution to Euler's equation for the flow of a frictionless fluid through a rectangular impactor. Numerical calculations were then carried out whereby the equations of motion of the particles were solved in a stepwise manner, leading to a determination of the efficiency curves. Since this theory assumed potential flow, the effect of Reynolds numbers on the characteristics of the impactor could not be determined.Ranz and Wong (1952) used an approximate flow field to calculate the efficiency of both round and rectangular nozzle impactors. In the vicinity of the stagnation point, the flow field was assumed to be that of frictionless stagnation flow. Here, the resulting equation of motion for the particles was found to be in a form similar to equations for free vibration with viscous damping. Therefore, the known solutions of the vibration equations were applied directly to the problem and the efficiency curves calculated. This solution technique, however, could not take into account the various geometric variations such as the jet-to-plate distance in the determination of the efficiency curves.The work of Ranz and Wong (1952) was later modified by Mercer and Chow (1968) and Mercer and Stafford (1969) so that the rather simple flow fields of Ranz and Wong (1952) could be used to account for various jet-to-plate distances. The same techniques, however, were used to determine the impactor collection efficiency curves."

Jan 1, 1986

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By George S. Rice

There have appeared, from time to time, comparisons of various features of coal mining practice in the United States and Great Britain. A recent, article, appearing in a British journal, points out that the American miner produces 3 1/2 times as much coal per shift as the miner, at one-half the cost, and proceeds to explain the natural industrial, and engineering causes which lead to this result. Amon« he reasons advanced. is that the American coal miner enjoys the advantage of more easily worked seams of coal, due to the fact that the coal mining industry in the United States is of more recent date than in Great Britain. The latter qualification is not correct, because where these advantages exist, they will persist. The coal beds of the United States are not buried deeply, except in the remote parts of the country, as in the Uinta Basin of Utah. The article referred to states that many of our miners are still employed on out seams reached by "adits", (which we term entries), or by vertical shafts of moderate depth. It is probable in fact that the great bulk of the coal of the United States is taken out from a depth of less than 400 feet.

Mar 1, 1920

By Earl C. Lane

This is the second of a series of reports on a survey of petroleum products manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in other parts of the United States, and the claim has been made that some of the present federal Specifications for petroleum products tend to discriminate against California products. The purposes of the present survey are to determine what particular specification requirements California petroleum products characteristically fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what &apos;lines investigation to determine the question should proceed. The first report* of the series gave the physical and chemical properties of gasoline and mineral spirits made from California crudes. The present report deals with lubricating oils. Sixty-one samples of lubricating stocks and finished commercial products were generously donated by four of the large refining companies of California. Fifteen samples of automobile lubricating oils, made in California from California crudes, were purchased in the open market. Nine samples of lubricating oils mode from Gulf Coast crude were contributed for comparison by a company in Texas. The refining companies have continued the helpful and cordial cooperation shown by them in connection with the earlier work of the survey.

Jan 1, 1923

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber-sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases soma of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving end.4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of ca· le left or the reel.7. The type of cable used.8. The kind of reel used.In connecti0n with an investigation of the general performance of rubber-sheathed trailing callas, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By J. B. Janus

This report continues a series of analyses of coal samples made by the Bureau of Mines in connection with the yearly purchase of several million tons of coal for various Government agencies. Listed are the analytical data on the composition and quality of tipple and de livered samples of coal collected during fiscal year 1974.

Jan 1, 1975

By T. M. Barczak

This report describes Bureau of Mines research to develop methods to evaluate loading on longwall roof supports to permit better design and more efficient utilization of these structures in compliance with the geological conditions in which they are employed. The resultant vertical and horizontal force acting on the canopy of a shield can be determined, either from a statically determinate solution assuming rigid-body mechanics and elimination of certain unknowns, or from an elastic solu-tion by analysis of the load-displacement relationship of the shield structure. A two-dimensional rigid-body model is presented that determines resultant shield forces by measurement of leg, canopy capsule, and lemniscate link forces. An elastic solution is presented, in the form of an elastic stiffness model with two degrees of freedom, which describes the load-displacement relationship from the stiffness of the shield structure as determined in the Bureau&apos;s Mine Roof Simulator (MRS). The ability of both models to determine resultant forces acting on the shield canopy are evaluated from full-scale tests in the MRS. More advanced numerical models are also discussed as part of the Bureau&apos;s continuing effort in the evaluation of roof support structures.

Jan 1, 1987

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981