Search Documents

By E. R. Palowitch

This report stems from a study by the Bureau of Mines of the possibility of reducing coal filter-cake moisture by applying radiant heat directly to the filter cake while under vacuum during the drying phase of the filter cycle. One disk of a 4-foot-diameter vacuum filter was equipped with gas-fired radiant-heat generators and the effect of radiant heating on the moisture content of a variety of filter cakes was studied. The results of this investigation show that this process can best be described as a filter aid capable of increasing the effectiveness of conventional filtration approximately 6 percentage points of moisture. The operating cost of removing water by this method is somewhat lower than the average operating cost of thermal drying and is considerably cheaper when the total cost is considered. Removal of water from coal that has been wet-cleaned is an important part of the overall coal preparation process. Water is a contaminant, and it is foolish to wash coal to reduce its ash content and add inert water in the process. In some instances the removal of water is actually more important than the removal of ash-forming minerals; its weight adds to the cost of transportation, and its evaporation during burning or carbonizing absorbs useful heat. Fine coal that contains more than about 10 percent moisture is notoriously difficult to handle. A problem thus exists for which there are sound practical and economic reasons to seek a solution.

Jan 1, 1961

By J. D. Hadden

The Bureau of Mines conducted drilling studies in the Pocahontas No. 3, the Pittsburgh, and a western coalbed to establish the gas migration characteristics for each. Gas pressures in the Pittsburgh coalbed were about 260 lb/in2 and in excess of 550 lb/in2 in the Pocahontas No. 3. Caving in drill holes prevented pressure measurements in the western coalbed. The Pittsburgh coalbed contained intersecting "clay veins" which formed gas pressure cells. Although these geological features hamper mining, they can be used to control the flow of methane into a mine working. Methane control techniques are proposed for the Pittsburgh and Pocahontas No. 3 coalbeds.

Jan 1, 1969

By Walter D. Holland

LFE Environmental performed an Industrial Hygiene survey of the Paraho Oil Shale Mining and Processing facility in Anvil Points near Rifle, Colorado, on August 6 and 7, 1975. This survey consisted of an investigation of the underground operations for diesel emission contaminants and of the above ground work areas for all inhalation contaminants other than silica dust. Samples were collected to investigate the following contaminants: respirable dust, total dust, NO2, NO, H2SO4, formaldehyde, CO2, S02 and CO. None of the determinations of contaminants in the underground operations indicate air concentrations exceeding their standards. The results for the samples collected above ground indicate only one operation where the employee's exposure exceeds the standards. It is a welding operation where the standards for total dust and lead are exceeded. Since the survey the employer has installed an exhaust ventilation system which has significantly reduced the welder's exposure.

Jan 1, 1976

By Thomas Varley

"During the past few years, since flotation has become the paramount treatment method for most all kinds of ores, the Bureau has gathered the data on consumption of reagents used in the flotation treatment. The first report was issued in 1916. A brief review of such reports shows the progress made in the art of flotation, and each year brings forth development of new reagents or combinations of reagents that seem sure to survive, but research and progress spell their defeat, if not by entire elimination, at least subjects them to considerable modification. Fortunately, close cooperation between the Bureau and the operators has been the means of an exchange of ideas in research work, and the development, in plant practice, of such research work on a commercial basis, is one of the outstanding features in milling today.In past years flotation has been referred to generally as ""oil flotation""— today it might be more properly called ""chemical flotatioin"" Minerals can be floated today without oil. Chemicals alone will do the work, showing how little was truly known about the process heretofore. The term ""regents as used herein, includes both chemicals and oils. The total pounds of oils and reagents consumed during the year was greater than shown in the 1925 report. The 1926 total was 201,711,795 pounds as compared with 81,688,967 pounds for 1925. The equivalent in pounds of reagent use& per ton of ore for 1926 was 3.933 as compared with 1.7972 for 1925. This increase is due largely to the amount of lime which is added in the alkaline circuits particularly in the mills treating coppers ores, which accounts for the larger tonnages."

Jan 1, 1928

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965

By H. A. Johansen

Recent advances in the metallurgy of chromium have enabled this metal to begin to take its place among the refractory metals. Considerable work is being done on the development of high-temperature alloys containing high percentages of chromium.1/2/ In spite of the relatively large amount of work done on these alloys, little is known of the properties of the pure metal. Information in the literature concerning the tensile properties of pure chromium metal is quite scant. This deficiency maybe explained by the great difficulty of preparing test specimens from such a brittle material, resulting in many losses in each phase of the specimen preparation and testing procedure.

Jan 1, 1954

By J. B. Gayle

A 1/2-ton experimental coke oven was installed ac the Bureau of Mines Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial slot-type ovens. Because of the small force exerted on the oven walls in most tests conducted to date (probably owing to the practice of charging coals and blends at a moisture content approximating that normal to commercial plants operating in this district), little information has been obtained about expansion properties. Two sole-heated ovens have therefore been constructed and used as supplementary equipment for determining the expansion properties of coals tested in the Tuscaloosa oven. The reasons for constructing the Tuscaloosa oven, the details of design, the operating, characteristics of the oven and the reproducibility of results have been discussed in previous publications. 3 4 5/ The present report deals with the effects of substituting various high- and low-volatile coals for components of a selected base blend carbonized under conditions similar to those normally used for producing foundry coke. Results of tests of 11 coals and 14 blends indicate that several blends tested rave cokes having physical properties very similar to those produced from the reference blend.

Jan 1, 1957

By Mayo D. Hersey

This problem was taken up by the Bureau of Mines as a result of the oxygen explosion at the Jefferson Physical Laboratory of Harvard University , and other similar explosions , in order to supply technical information which would serve as a basis for safety precautions in the future . At the Harvard inquiry the fact was emphasized by the Massachusetts State Chemist , Mr. Walter M. Wedger , that we do not know the limiting pressures and temperatures above which compressed oxygen and lubricating oil are capable of spontaneous explosion . The problem is also of importance to the Army and Navy and to the Bureau of Mines in connection with the hazards incurred in the use of compressed and liquified gases in the repurification of helium. In fact , the risk of fires and explosions due to traces of lubricating oil coming into contact with high pressure oxygen is of serious interest to all concerned with the manufacture and use of oxygen , a commodity which is now being produced and distributed on a rapidly increasing scale . Part of the money expended on this investigation was from Army and Navy funds . The problem was undertaken by the Bureau of Mines at the suggestion of Dr. Charles E. Munroe , Chairman of the Committee on Explosives Investigations of the National Research Council , and referred to the Pittsburgh experiment station of the bureau.

Jul 1, 1923

By Ronald D. Hill, Elmore C. Grim

Sediment is one of America's greatest pollutants. More than a billion tons of sediment reach the major streams of the United States annually(l). Damages are reflected in the reduced carrying capacity of streams, clogged reservoirs, destroyed habitat for fish and other aquatic life, filled navigation channels, increased flood crests, degraded facilities for water-based recreation, increased industrial and domestic water treatment costs, premature aging of lakes by enrichment of the water with silt-carried fertilizer that promotes algae growth, destroy crops, and reduce productivity of flood plain soils. Erosion and sedimentation are natural processes that are usually gentle actions releasing controlled amounts of silt from watersheds to receiving streams. Surface mining activities accelerate these natural processes and short duration, high intensity storms can become a violent force moving thousands of tons of soil in a brief period of time. Cover is a very important factor. With the removal of ground cover, water moves across the denuded area on its own terms picking up soil particles as it flows and leaving gullies behind. The susceptibility of strip-mined land to erosion depends on: 1.Physical characteristics of the overburden 2. Degree of slope 3. Length of slope 4. Climate 5. Amount and rate of rainfall 6. Type and percent of vegetative ground cover. By development of erosion and sedimentation control plans before disturbance of the area, many of the detrimental effects of strip mining can be prevented.

Jan 1, 1974

By W. L. Schmidt

The effect of a water-repellent film in sandstone cores on the effective permeability-saturation relationship was investigated as part of a cooperative research program between the Bureau of Mines and the American Gas Association. The repellent film was formed by the reaction of methyltrichlorosilane3 with the connate water in the core. Other researchers have reported on the use of silicone chemicals to alter the flow characteristics of porous media (1-3, 5-7, 9, 10).4 The previous studies, however, dealt almost entirely with oil-water or oil-gas systems and not with water-gas systems. The primary purpose of this study was to determine the feasibility of using silane to retard the influx of water into natural-gas storage wells and to determine the necessary requirements for achieving this result. The success or failure of silane treatment as a remedial measure depends on its effect on gas-production rate and attendant water production.

Jan 1, 1961

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By Adrian J. Mathias

This report presents the results of an investigation of a mine production-scheduling model and a critical path analysis for long-range mine planning. An example is given to illustrate how these techniques might be used to plan long-range development and production scheduling for a large underground mine. The model, based on estimated ore block grades and tonnages, and on designed mine development layout, simulates mining of ore blocks in a sequence necessary to fulfill mill requirements for ore tonnage and grade evaluation within pre-established system restrictions. Simulated production schedules are obtained as output from the model. These production schedules are then incorporated into a critical path analysis to determine the sequence for the long-range development work so as to fulfill the production schedules and thereby meet the ore grade and tonnage requirements of the mill.

Jan 1, 1967

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

By Robert H. Peters

Are the safety rules in your work place effective? Do supervisors enforce them as they should? Do supervisors abide by these rules? Safety rules are an important aspect of many company safety programs, particularly if employees must work in an intrinsically hazardous environment such as a coal mine. However, for various reasons, supervisors sometimes fail to enforce safety rules (Arvey & Jones, 1985; Hartshorn, 1998). This paper presents some findings obtained from interviews with coal miners about why supervisors sometimes fail to enforce an important mine safety rule. It also contains a few suggestions addressing what could be done to help supervisors perform this job function more effectively.

By E. J. Kloos

This publication lists devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, as of May 24, 1972, under provisions of Section 11.2, Part 11, Subchapter B of Chapter 1, Title 30, Code of Federal Regulations (37 F.R. 6244, March 25, 1972), for use in mines as respiratory protection in oxygen-deficient atmospheres, and in gases, vapors, dusts, fumes, and mists. Included are self-contained breathing apparatus, gas masks, and supplied-air, dust, fume, mist, and chemical-cartridge respirators. Names and addresses of manufacturers appear in the appendix.

Jan 1, 1972

By Q. H. Forbes

"The high injury rand fatality rate in coal mining, as compared with other industries, has caused the mining industry to become more and more interested in accident prevention methods.The prevention of accidents in the mining industry is probably not as simple a problem as it is in other industries, but if the experience of coal mining companies who have taken up the work of accident prevention seriously during recent years means anything, there is little doubt that most mining companies car improve their accident records very materially.Such results can be obtained in practically all instances without adding to production costs. In fact, there is little doubt that a well-organized program of accident prevention Will bring about a 'material production cost reduction due to increased efficiency, lower labor turnover, fewer delays due to accidents, better satisfied workmen, and a direct saving in compensation costs as well as many other items of expense.The more closely a. person is connected with the work of accident prevention, the more he becomes a believer in the value of amity in human relationships and the more he is able to exercise a spirit of toleration, fairness, justness, and helpfulness toward the problems of others, whatever those problems may be. Human nature responds to just these expressions of good willAnother great and invaluable effect of working for safety, is the fact that it is building up in the mind an appreciation of that which is constructive and, conversely, in opposition to that which is destructive In other words; the person who is sincerely striving to prevent accidents because they are destructive, costly, tad injurious, is subconsciously training his mind to look on any proposition from a constructive point of view. Working for accident prevention and safety is about the finest social training any person can have. It does not make a Person a financial Wizard or an executive genius, but it does make for the highest type of citizenship.While humanitarian reasons alone should be sufficient to maze accident prevention work an important factor in every mining organization, there are other reasons as well, since it has been proved conclusively that there can be no efficiency and economy without safety, as somebody pays when safety is lacking. Every safety device pays dividends; every safety application evaded is an assessment and a loss. Dangerous conditions are the most expensive and extravagant conditions in or about a coal mine. The economic gains are of considerable interest to all coal mining companies and this is brought about as before stated--through decreased compensation rates, the reduction of labor turnover, etc."

Dec 1, 1930

By E. C. Lane

This report on properties of commercial motor fuels is the twelfth in a series made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data on motor gasolines sold during the winter of 1935-36.V The -present report, covering the summer of 1941, presents analytical data for 1,857 samples, representing the products of approximately 135 companies. As in previous surveys, these companies include both large and small suppliers. In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted, and these data are published exactly as they were received. Conforming to previous surveys, the data cover three groups of samples -- regular-price, premium-price, and third-grade gasolines -- and each group has been aver aged separately. The number of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, are as follows: Regular price, 1,010 samples, 291 items, and 86 brands; premium price, 577 samples, 263 items, and 78 brands; third-grade gasoline, 270 samples 159 items, and 74 brands. The meanings of these terms as used in the surveys are as follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.

Jan 1, 1942

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010