Search Documents

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state, Adsorbed gas is stored in the micropore structure and its transport is governed by Fick's law. The free gas occurs in the. fracture system and flows according to Darcy's law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds.

Jan 1, 1969

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESRJ spectrum of the hydroxyl (· OH) radical spin adduct with .the spin trap 5,5-dimethyl-1-pyrrolintt-N-oxide has been obtained in suspensions of freshly ground quartz particles. The concentration of the spin adduct (and hence of the • OH radicals) increases with the amount of grinding. The dust's potential for the generation of the· OH radicals is maximum when fresh (i.e., immediately after grinding) and decreases to 50% in about a day on storage in air. Studies involving metal chelates .indicate that the • OH radical formation involves mainly the silica surface and H20 rather than the Fenton reaction. The results suggest that hydroxyl radical reaction(s) could be important in the lipid peroxidation and fibrogenicity by quartz dust, particularly .in acute silicosis. INTRODUCTIONIn this paper we report on our electron spin resonance (ESR) detection of the formation of hydroxyl (·OH) radicals in aqueous suspensions of freshly crushed quartz particles. This work was undertaken with a view to find possible clues to the role of free radicals in the pathogenesis of quartz-induced fibrogenicity, commonly known as silicosis. We noted that while silicosis is one of the major health hazards in coal and mineral industries, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still poorly ·understood (Reiser and Last, 1979; Singh and .Rahman, 1987). It is generally thought, nevertheless, that the action of quartz particles on the biological membranes is the starting point of the silicotic process (Parazzi et - al., 1968). A possible clue to the mechanism of the membrane damage by quartz particles, in terms of the role of oxygenated free radicals, is suggested by the following observations. A suspension of quartz particles in contact with alveolar macrophages has been reported (Gabor et al., 1975; Koike et al., 1982) to initiate an enhancement of lipid peroxidation, defined broadly as the oxidative deterioration of polyunsaturated components of lipids. Hydroxyl (· OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (Halliwell and Gutteridge, 1985) and of initiating lipid peroxidation in lysosomal membranes. (Fong et al., 1973). Arong other lines, it is known that exposure of cell membranes, fatty acids, and unsaturated food oils to ionizing radiation, which generates· OH radicals, causes rapid peroxidation (Halliwell and Gutteridge, 1985). Thus • OH radicals (and also other oxygenated species such as Oi, 10 2, and H20 2) might be expected to play a role in the toxicity of quartz. Earlier studies of the aqueous chemistry of quartz suspensions have reported detection of H2O 2 (Kalbanev et al., 1980), implicating the formation of ·OH radicals as transient species. However, we are not aware of any report of the detection of • OH radicals in quartz reactions, and thus the present study was undertaken. Since it-is known that, because of their high reactivity (hence short lifetime) in aqueous media, the • OH radicals cannot be detected via ESR directly (Finkelstein et al., 1980; Buettner, 1982) we have used .ESR combined with the spin-trap methodology (Finkelstein et al., 1980) for studying the· OH formation. The results show that· OH radicals are indeed formed in aqueous suspensions of freshly ground quartz; thus pointing to ·a possible new clue to the cytotoxicity of freshly formed quartz particles and thereby to silica fibrogenicity."

Jan 1, 1988

By N. S. Dalal, B. Jafari, F. H. Y. Green, M. M. Suryan, V. Vallyathan

"Freshly ground and aged anthracite and bituminous coal samples were investigated by electron spin resonance (ESR) spectroscopy to detect the presence, concentration and reactivity of free radicals. Freshly ground anthracite coal produced greater concentration of free radicals than the bituminous coal, and the radical reactivity was also greater for the anthracite. The reactivity of the newly produced free radicals in the anthracite dust correlated with the dust's toxicity. Furthermore similar coal-based free radicals were detected in the lung tissue of autopsied coal miners, suggestive of persistent reactivity by the embedded coal dust leading to the progressive disease process. Results of the studies on the severity of coal workers' pneumoconiosis (CWP) and free radical concentration m lung tissue support this hypothesis.INTRODUCTIONCOAL WORKERS' PNEUMOCONIOSIS (CWP) has been an important topic of concern to miners, mining engineers, epidemiologists and medical researchers for decades. It is well known that the prevalence and severity of CWP differ markedly between different regions and mines despite comparable exposures to respirable dust (REISNER and RoBOCK, 1977; HURLEY et al., 1979). These variations in pathogenicity of coal mine dusts can only partially be explained by differences in the mineral composition and by rank of coal (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). Cytotoxity studies on mammalian cells do not correspond well with the human disease pattern (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al.,1980; VALL YA THAN et al., 1988). For example, while epidemiological studies of coal miners (REISNER and ROBECK, 1977; HURLEY et al., 1979) indicate that the prevalence of CWP correlates roughly with the rank of coal, such correlation has not yet been established in biological studies, despite considerable effort (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). In order to help resolve this apparent paradox we have undertaken a systematic study to evaluate whether any correlation exists between the concentration of free radicals present in fresh or aged coal dusts from two well-characterized U.S. coals. This study was also prompted in part by observations reported in the literature that organic free radicals can be formed on the surface of freshly fractured coals (LEBEDEV et al., 1978; DULIBA and CLARKSON, 1984). In particular, ARTEMOV and REZNIK (1980) noted that the decay lifetimes and, hence, the reactivity of the organic free radicals formed on crushing Russian coals, .depended"

Jan 1, 1989

By Charles E. Munroe

At the outset of the war the uncontrolled production and possession of explosives obviously became a serious menace to the safety of persons and property and the successful conduct of military opera- tions. Even in the years immediately preceding the entrance of the United States into the Great War explosives were employed in attempts to wreck munitions plants as at Eddystone, Pa., or to inter- rupt transportation and conveyance by demolition of munition-laden cars as at Black Tom Island, N. Y., or by attacks on ships, bridges, and viaducts. Outrages with explosives, such as that which Holt inflicted on the Senate reception room, United States Capitol, were not infrequent, and often caused serious loss of life and injury to persons as well as destruction of property. The regular manufacturers of explosives were keenly alive to this menace and early took such steps as lay within their power to meet it as is shown by the following letter:

Jan 1, 1921

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By Michael Hamilton

Mineral resources have been identified at two properties in the Ten takes RARE II area (table 1). Commodities consist of copper and silver. The deposits, in the northwest part of the study area, are hydrothermal and associated with fissure veins that developed along northwest-striking faults within the Precambrian Purcell Lava. In addition to the identified resources, there is high potential for additional copper-silver resources at these properties and moderate potential for copper-silver-lead-zinc-bariun resources at five others (table 2) in the portion of the study area that is underlain by the Purcell. There is no evidence that significant mineralization occurred in strata above or below the Purcell.

Jan 1, 1983

By W. W. Weller

Low-temperature heat capacities of scandium sesquioxide (Sc203) and a mixture of cerium sesquioxide (Ce203) and cerium dioxide (CeO2) were measured over the temperature range from 50° to 298° K. The entropy of scandium sesquioxide at 298.15° K was evaluated directly as S°298.15 = 18.4 ± 0.1 cal/deg mole. That of cerium sesquioxide was extracted by combining the heat-capacity data for the mixture with those for pure cerium dioxide; the result was S298.15 36.0 ± 1.0 cal/deg mole.

Jan 1, 1963

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989

By J. A. Sutton

In connection with, a stream-pollution-research project, a colorimetric method was developed for concentrations of 1 to 30 p.p.m, of pine oil in water. The method depends on the stable bluish-green color produced when pine oil is reacted with vanillin-hydrochloric acid reagent at 60° C. for 25 minutes. The colorimetric reaction actually determines alphaterpineol, the principal component in pine oil. Some waters may require a special preparation in which ion-exchange resins are used to remove interference. ACKNOWLEDGEMENTS The author wishes to express his appreciation to A. A. Berk, chief of the Industrial Water Branch, Bureau of Mines, for helpful advice and encouragement during the progress of this work and to B. P. Martinez, chief of the Stream Pollution Research Section, for assistance with the manuscript. Thanks are also due to W. D. Bishop of the Hercules Powder Co., Wilmington, Del., for supplying the principal components of pine oil.

Jan 1, 1953

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

By J. R. White, S. W. Lambert, C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08" for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976

By F. E. Brantley

Blister copper was successfully deoxidized with any of a variety of reducing gases; lancing techniques or a vertical-column furnace were used to contact the copper and gases. Of the gases tested, butane, when used to lance molten copper at about 1,200° C, reaction temperature, was slightly more effective than propane, natural gas, carbon monoxide, or reformed gas for deoxidizing copper from about 1.0 to less than 0.1 percent oxygen content, Laboratory-scale tests revealed that the vertical furnace, composed of a heated column packed with silicon carbide chips or hollow carbon cylinders, was significantly faster and more efficient than the lancing technique for deoxidizing molten copper with any of the gases tested. Comparison of the gaseous-reduction method with the conventional poling method suggests that the gaseous method has important technical and economic advantages for deoxidizing blister copper to any readily controlled amount of residual oxygen content.

Jan 1, 1962

By T. R. Strombotne

The purpose of this report k to document a contract undertaken by TSA Systems, Incorporated for the United States Bureau of Mines to develop a commercially available source of a continuous, working,, level detector for the measurement of radon daughter products in various working environments. The basic radon measuring technique was devised by Robert Droullard and Robert Holub and has been applied here. For further details or purchasing information contact: TSA Systems, Incorporated 4919 North Broadway Boulder, Colorado 80302

Jan 1, 1982

By Allen D. Look

Underground fires often prove difficult to control , and a small fire can quickly grow into a large one , endangering life and causing large property damage . Even a small underground fire may produce enough noxious gases to cause suffocation ; therefore , every precaution should be taken to prevent and control such fires . It is ironic that mine fires should be caused when utilizing materials that are in themselves fire - resistant ; yet , cutting and welding of iron and steel are proving to be common causes of underground fires in metal mines . This paper includes 19 examples of underground fires of this nature , and undoubtedly this is only a fraction of the number of similar fires that have occurred in the last few years . This paper will review some metal - mine fires caused by cutting or welding and point out precautions to be taken to prevent other fires from this cause .

Apr 1, 1948

By M. Clair Smith

This report is one of a series describing exploration, development, mining, and processing of mineral deposits in the United States. The reports are prepared and published by the Bureau of Mines in cooperation with various mining companies The purpose of the reports is to promote development and conservation of our natural reserves by disseminating technological information on mining and milling procedures and related practices at operating mines. Simplot Silica Products, Inc., mines and processes a friable silica sandstone. The finished products are sold for use in glass manufacture, foundries, chemicals, and special applications.

Jan 1, 1959

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964