Search Documents

By Lloyd Williams

1. The investigation shows that the bed identified as Wilder in this report is the only bed in Overton County that has produced commercial coal and is the only bed in which coal reserves were estimated for this report. Three other coal horizons were recognized but lacked enough data for reserve estimates. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 19 million short tons, as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas of the Wilder bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By D. A. Douglass

This report describes the tri-n-butyl phosphate extraction of cerium (IV) from a sulfate leach liquor prepared from a bastnaesite concentrate as well as from pure eerie nitrate solutions. The work was done on a laboratory scale using separatory funnels. Extraction from pure cerium solutions entailed no great difficulties; however, extraction from the bastnaesite solution proved more difficult, mainly because of the inhibiting effect of the sulfate ion. Despite this, procedures were developed for obtaining good single-state cerium extraction (95+ percent) and a high-purity product (99+ percent), although the maximization of both cannot be achieved simultaneously. This necessitates a compromise in any extraction scheme.

Jan 1, 1959

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By C. T. Sheeran

The Bureau of Mines investigated a microprocessor-based real-time control and monitoring system for uranium mining applications. The system is capable of controlling and monitoring up to 768 stations within 3 km of the central processor on a common four-wire cable. It can be used in conjunction with detectors to continuously monitor and display radiation working levels at points throughout the mine. Surface alarms are sounded for critical situations such as rapid radiation buildup, loss of power to monitors or fans, and changes in air door position. Permanent records of all changes are automatically printed out with their time of occurrence. Printouts can also be obtained for shift reports or trend logs. The system can be used to remotely control fan startup and shut-down, and also can alert miners of underground conditions by blowing horns or turning on lights. Battery backup keeps the system operative for up to 4 h in case of a mine power outage. A special software feature permits automatic, time-delayed, sequential restart of fans.

Jan 1, 1984

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are investigating technology and methods to monitor the blind areas around large haulage equipment used in surface mines. On average, six fatalities a year can be attributed to equipment colliding with other vehicles or pedestrian workers, or backing over the edge of a dump point. Several off-the-shelf technologies exist for monitoring areas that an equipment operator cannot see from the cab, including radar, video cameras, and radio signal detection systems. NIOSH researchers have tested many of these systems on large dump trucks both at their test facility and at surface mines. This article discusses the technologies available for this application and their effectiveness in detecting objects near an off-highway dump truck. Also, guidance is presented for mine safety personnel who are planning to evaluate collision warning systems or cameras on their haulage equipment. Available Technology Over the past few years, the number and types of systems available for monitoring the blind areas around heavy equipment have increased. Systems marketed for the automotive and recreational vehicle industries have been around for a while. Small video cameras can be found

By Albert E. Long

Preliminary experiments conducted in 1949 with a few diamond bits in which the diamonds in the bit crowns were set in hard-vector directions indicated that a substantial saving could be effected when a high percentage of the diamonds were oriented in this-manner. It was realized, however, that many additional tests would have to be performed before a positive trend could be established and the possibility of coincidence eliminated. Therefore, a long-range series of experiments was planned to investigate various phases of the problems related to the orienting of diamonds in diamond bits. This report (the third in a series) 2/3 presents the information obtained from tests conducted to investigate more fully the effects of orienting high-grade drill bort in diamond bit crowns. In these tests, the drill bort were oriented in both hard-vector and soft-vector directions in the crowns of AX-size bits. Test drilling was done in a dike of saussuritized dacite porphyry similar to a fine-grained granite in hardness e drillability.

Jan 1, 1954

By C. B. Barmore, B. W. Gandrud, B. M. Bird

"The Bradford mine of the Alabama By-Products Corporation is located in the Warrior coal field of Alabama, in the northern part of Jefferson County, about 25 miles north of Birmingham. The coal mined from the Black Creek bed at this point is not considered to be ideal for coke making by itself but because of its exceptionally low ash content is mixed with the higher-ash coking coals from other beds of the district to control the ash content of coking mixtures. Further reasons for using this coal only as a diluent of the higher-ash opals are that the thinness of the bed renders the production costs relatively high and the reserves are somewhat limited.This paper, which is the fourth of a series on the washability of Alabama coals, Like its predecessors dealing with the Mary Lee beds and the Clark bed,6 contains screen-sizing and float-and-sink tests of a representative sample of the raw coal, and flakiness tests showing the proportions of flaky particles in certain selected sizes. However, inasmuch as the float-and-sink tests of the coarse sizes showed excellent liberation of coal from impurities, crushing tests have not been considered necessary.The data on which this report is based have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods."

Apr 1, 1931

By A. Aly Selim

This report describes the feasibility of predicting percussive drilling rates by equations derived from statistical regression analysis. The least squares statistical method was used and the analysis was performed both by direct and by stepwise linear regression analysis. The predicted penetration rate is a function of the drill power and the physical properties of the rocks penetrated. The results show promise that the technique may be of value in providing a mathematical model by which percussive drill manufacturers and users can predict the performance of a given drill. Experimental work involved two mining type percussive drills. Penetration data for these drills were determined from nine rocks drilled in the laboratory. Drill work rates (power) were determined in a separate series of experiments. Rock physical properties were measured from diamond-drill core samples taken from the same blocks used for percussive drilling.

Jan 1, 1970

By Gordon L. Kinney

The only economically important mineral currently produced in Bangladesh was natural gas. Bangladesh was not a world? ranked producer of any mineral commodity, but the possibility of producing and exporting commercial amounts of liquefied natural gas (LNG) was being examined. Proved reserves of natural gas were sufficient to supply most of the country's industrial and domestic heating and electric needs and still support an export-oriented LNG plant. Other mineral production was of virtually no significance to the economy, although there were a few prospects for nonmetallic mineral development. Bangladesh continued to make economic progress during 1978 and into early 1979. Gross domestic product (GDP) at current prices rose from $6.6 billion in 1976-772 to $8.2 billion in 1977?78 and $9.3 billion in 1978.79.2 In fiscal 1979, the economic conditions were favorable until a severe drought hit most of the country. It W88 reported that conditions were the worst in 40 years, and 88 of July 1979, substantial crop losses were predicted. The agricultural sector accounts for over 53% of the GDP and about 75% of all employment. The poor weather will cause economic problems in the form of slower growth, larger trade deficits, and a higher rate of inflation. The 1978.79 statistics showed that real GDP increased just 4%.

Jan 1, 1981

By S. H. Lorain

This paper is one of a series on mining and milling method and costs being published by the United States Bureau of Mines. The Golden Messenger mine, operated by the United Gold Mines Corporation, is in the York-Confederate Gulch mining region in Luis and Clark County, Mont., 22 miles northeast of the city limits of Helena and about 1 mile north of the town of York. It is the first operation to exploit successfully the low-grade ores of the York-Confederate Gulch area. The unusual vein structure presents some mining problems that have been solved in ail interesting manner.

Jan 1, 1937

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By Jack E. Tress

The Bureau of Mines has been involved for several years in the development of processes for the recycling of solid wastes. As part of this program, a project was initiated to determine the feasibility of producing secondary pig iron from auto scrap. During the test period, 86,000 pounds of shredded auto scrap, along with petroleum coke and fluxing agents, was charged to a submerged-arc furnace of 1-ton nominal capacity. Eighty-eight thousand pounds of pig iron, with an average carbon content of 3.90 percent and an average copper content of 0.2 percent, was produced at an electrical consumption of 512 kW-hr per net ton. A cost estimate of the process showed that the pig, iron might be produced at a cost of $57 per ton.

Jan 1, 1973

By Scott Turner

Within recent years , people have begun to realize the importance and significance of the mining and allied industries . The leading part the engineer plays in civilization is becoming recognized . However , accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business . It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization , but on the whole , the magnitude of the industry is underestimated . The uncertainties of mining , as evidenced by the variable results of prospecting on surface or underground , in an unknown new field or from the bottom levels of a mature mine , the ins and outs of tonnages and metal contents , the possibility of a widespread or even a sudden change between cost and realization-price , add to its picturesqueness and make mining attractive to some . To many , the fact that results are generally more uncertain and less predictable than in other industries lends added charm . The following pages may serve to call attention briefly to the importance of mining relative to other industries in the United States , in Canada , and in the world . Ordinarily , the annual primary mineral production of the United States amounts to about 5 billion dollars . The average for the last five years has been a little over 5 billion dollars . Last year , sadly enough , it was less than 34 billions . Just now , we are on the decline , and have been for the past two years . In Canada , the 5-year average was about 268 million dollars . Last year it was 227 million . Due in part to gold output ( in 1930 , for the first time , Canada's gold production exceeded that of the United States ) , the Canadian average is holding up better than ours . It has been estimated that the average world mineral production over the past five years has amounted to about 12 billion dollars , while in 1931 it was less than 8 billions . The mineral industries are as indispensable for the conduct of modern society as are those of agriculture , but , in the United States at least , they receive far less recognition from the Government . With us , agriculture is fostered by a great department that is maintained by enormous appropriations , while the mineral industries get but little financial support . In the United States , in the calendar year 1930 , the value of production by these two industries were as follows : to 1 . Agriculture ( inclusive of forestry ) 9.9 billion dollars ; mining 4.8 billions ; ratio 2 Direct appropriations by our Federal Government were 109 million dollars to agriculture and 2.8 million to mining , a ratio of 39 to 1. Obviously this is out of balance to the extent of 19 to 1 in favor of agriculture .

Jun 1, 1932

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By Mary F. Koehler

Interoxidic compounds, such as vanadates, have not been studied extensively in the field of thermodynamics. This is a report of three vanadates of sodium--metavanadate, pyrovanadate, and orthovanadate. Vanadates of other metals will be considered in future reports. The heats of formation at 298.15° K. of the three sodium vanadates (both from the oxides and from the elements) were derived from the results of sodium hydroxide solution calorimetry. Free energies of formation were obtained by combining heat and entropy values. The results support the conclusion that the three sodium vanadates were stable with respect to all possible decompositions in which vanadium retains its pentavalency.

Jan 1, 1960

By B. G. White

NIOSH researchers have identified a pattern of fracture zone development that suggests an explanation for fracture formation around rectangular openings in underground mines. This pattern is characterized by shearing and dilation that result in either faults or in the repeated formation and propagation of en echelon fractures from sites of tension. Two computer modeling codes, Fast Lagrangian Analysis of Continua (FLAC) and Particle Flow Code (PFC), were used to model different aspects of this pattern. Use of very small elements with FLAC enabled the identification of sites of initial tension near the skin of square-cornered rectangular openings, while PFC allowed the initiation and progressive development of fractures from these sites to be followed as the fractures evolved. Such studies can lead to a greater understanding of how roof support can be better selected and installed for specific conditions in underground mines prone to roof falls and rock bursts. These studies may also lead to modifications of corner and opening shapes that could be incorporated into mine designs to produce more stable mine openings and reduce the risks of rock falls and rock bursts.

By W. H. Hamilton

The Kokomo (Tenmile) mining district has had an output valued between $20 and $30 million, mostly from production of silver, lead, and zinc, since 1878. For many years before World War II, there was little production, as the complex nature of the ores made them unattractive at existing metal prices. Under the stimulus of the war, the Geological Survey and the Bureau of Mines studied they district, and in October 1944 the Bureau of Mines began an exploration project, which included dia¬mond drilling, bulldozer trenching, and geophysical surveying. Project work was continued until March 1949, except for short recesses during 1945, 1947, and 1948. Forty-five diamond-drill holes, totaling about 13,000 feet, were drilled from underground and surface stations on the various properties in the district. Eleven bulldozer trenches, abut 2,400 linear feet, were excavated in an attempt to uncover the outcrop of the middle Quail limestone. These trenches ranged from 100 to 485 feet in length and reached a maximum depth of 15 feet. A limited geophysical investigation was made during the summer of 1946. The length of the traverses were: Magnetic, 990 feet; resistivity, 6,250 feet; and self-potential, 69,780 feet.

Jan 1, 1955