Search Documents

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Nicholas County, W. Va. It is one in a series describing coals suitable for producing metallurgical coke, either as mined or after beneficiation. Almost 5 million tons of coal were produced in Nicholas County, W. Va., in 1960, of which over 2.6 million tons were cleaned in eight preparation plants. It has been estimated that over 6 billion tons remained in the county as of December 31, 1960, in beds 12 inches and more thick.

Jan 1, 1962

By Horace C. Porter

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantities, a series of tests was begun in the fall of 1909 under the supervision of J. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for example, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New River (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a full account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included.

Jan 1, 1917

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By G. L. Cook

The design of a dual-inlet system for a Consolidated model 21-103C mass spectrometer is described in detail. The system permits both high-mass and low-mass samples to be run by using a single instrument. The difficulties of using a single instrument for both purposes are given and a method of minimizing these difficulties through the use of the present design is discussed, After examining the experience of five years of use, the conclusions are that the bimodal operation is practical and the low-mass analyses had nearly the same precision as before the modifications to the instrument were made. In 1951, O'Neal and Wier.5/ published the first description of the modifications made to a mass spectrometer so that the spectra of hydrocarbons with molecular weights up to 600 could be obtained. Further discussion of the equipment of O'Neal appeared in 1953.6/ Also, Brown, Melpolder, and Young7/ described a parallel inlet system designed to reduce sorption effects at room temperature.

Jan 1, 1960

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963

By Joseph A. Sutton, John D. Corrick

The chemistry involved in the microbial dissolution of iron and copper from such sulfide minerals as pyrite, chalcopyrite, chalcocite, cove11ite, and bornite is described. The chemical criteria used to evaluate the activity of microorganisms on these minerals were changes in pH, ferric iron produced, and oxygen consumption. In a series of experiments in which a ferrous sulfate nutrient solution was percolated over small portions of the above-mentioned copper sulfide minerals for 56 days, the iron-oxidizing bacteria Ferrobaci11us ferrooxidans and Thiobaci11us ferrooxidans were capable of bringing about the dissolution of 23.7 percent of the copper from chalcocite, 56.3 percent of the copper from cove11ite, and 29.8 percent of the copper from bornite by the microbial production of ferric sulfate which reacted with these minerals. Laboratory tests have demonstrated that pure strains of the iron-oxidizing bacteria act as catalysts to the ferrous iron being oxidized by the Oxygen of a system containing pyrite and chalcopyrite. In a series of experiments during which nutrient solution was percolated over pyrite for 70 days, the ferric iron produced by the iron-oxidizing bacteria was 112 to 120 times greater than that produced atmospherically.

Jan 1, 1964

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By Martin J. Gavin

In an earlier paper (Karrick, Lewis, C. A convenient and reliable retort for assaying oil-shales for oil yield: Bureau of Mines, Reports of Investigations, Loral No. 2229, March, 1921. Reprinted in Eng. and Min. Jour, April 30, 1921, also in Mining & Met., May, 1921) which describes the apparatus and method used in the laboratories of the Bureau of times for assaying oil-shales, no mention is made of the quality of oil obtained when the apparatus is operated under conditions determined to be most suitable for producing highest yields of oils. So many inquiries regarding the nature of the oil have been received, that it seems advisable to present a short report on the subject. Experimental work indicates that it is possible to vary the quantity and quality of the oil obtainable with the assay retort from a given shale by varying the conditions of retorting. As an example, some figures that are averages for several closely agreeing tests are shown below.

Jan 1, 1921

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By S. J. Schatzel, P. W. Jeran, W. P. Diamond, F. E. McCall, F. Garcia, J. C. LaScola, T. P. Mucho

The National Institute for Occupational Safety and Health, Office for Mine Safety and Health Research, is investigating the geologic and mining factors influencing the migration of longwall gob gas. One goal of these studies is to optimize methane drainage strategies to reduce the volume of gob gas that reaches the underground workplace. As part of this research effort, longwall gob gas flow paths in a mine operating in the Pittsburgh Coalbed, PA, were investigated using SF6 tracer gas. Tracer gas released into the ventilation airflow underground generally stayed in the bleeder system and was vented at the associated bleeder fan shafts. Tracer gas injected into an inactive (intaking) gob gas venthole migrated to the two inby producing ventholes on the study panel, indicating that all three ventholes were in communication. The tracer gas that was injected into the gob generally stayed in the gob and only migrated to the ventilation system in response to the venthole on the study panel closest to the injection hole going off production. Tracer gas flow velocities in the longwall gob reservoir and factors influencing the production performance of gob gas ventholes in the study area are also discussed.

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By D. A. Rice

As part of its mission, the U.S. Bureau of Mines continues to develop technologies that will enable cost-effective compliance with environmental requirements. To this end, investigations to improve the kinetics of chalcopyrite dissolution by simultaneous grinding-leaching in ferric sulfate solution were conducted using the Bureau-designed turbo mill. The development of such a hydrometallurgical process would provide a nonpolluting alternative to conventional smelter technology. The effects of mill rotational speed and volume percent solids on the leaching time and energy required for copper extraction from chalcopyrite were evaluated. The results of this laboratory study have shown that the simultaneous grinding-leaching of chalcopyrite concentrate using the turbomill is technically feasible with essentially 100 pet extraction of copper being possible at 90° C. An optimal energy consumption of 1,153 kW?h/st of copper leached was found in batch testing with the mill operating at 400 rpm with a slurry containing 35 vol pet chalcopyrite. This energy consumption, while higher than other proposed leaching processes (about 600 kW?h/st), is of the same order of magnitude. Further refinement of the energy requirements would require additional testing using a continuous circuit. Leaching times of less than 1 h, for 80 pct copper extraction, are achievable using the turbomill grind-leach process.

Jan 1, 2010

By Richard A. Winters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,680-acre Lime Canyon Wilderness Study Area (NV-050-231) to evaluate its identified mineral resources. The Wilderness Study Area is in Clark County, NV, about 30 air miles southwest of Mesquite, NV. The area studied contains an estimated 44 million tons of indicated subeconomic resources of gypsum, an inferred subeconimic resource of limestone and dolomite, and occurrences of gold, copper, uranium, and zeolite. The Wilderness Study Area is underlain chiefly by carbonate rocks with lesser amounts of sandstone and shale. Metamorphic, granitic, and volcanic rocks also crop out within the area. Large portions of the area are overlain by alluvium. The Wilderness Study Area is within the Gold Butte mining district. Several gold mines with past production are nearby to the south of the Wilderness Study Area; one mine is reported in operation on a small scale. Several silver-bearing copper and zinc mines with past production are nearby to the east of the Wilderness Study Area

Jan 1, 1988

By J. B. Zink

The Bureau of Mines developed a spectrochemical method to determine six constituents in coal ash in the following concentration ranges: silica 9 to 63 percent, alumina 7.5 to 35 percent, ferric oxide 2 to 30 percent, calcium oxide 1 to 29 percent, magnesium oxide 0.5 to 6 percent, and titanium oxide 0.5 to 4 percent. Samples of coal ash are fused with a mixture of lithium tetraborate and vanadium pentoxide. The resulting beads are crushed, mixed with powdered graphite, and briquetted. The pellets are analyzed spectrographically, using controlled high-voltage spark excitation. Vanadium serves as the internal standard. Effects due to matrix variations are minimized by fusion with lithium tetraborate. Intensity ratios of selected analytical lines are determined photometrically, Concentrations are read from analytical curves, prepared from synthetic standards, relating log intensity ratios to log concentration. A combustion procedure is used to determine sulfur tri-oxide. The method is most useful when large numbers of coal ashes must be analyzed but a high degree of accuracy is not essential.

Jan 1, 1967

By H. J. Heinen

Excellent gold recovery was demonstrated in a laboratory-scale leaching test on waste material from an open-pit mine in northeastern Nevada. An injection system of leaching was applied in which the sodium cyanide solution was introduced into the interior of the dump at selected points. Dissolution of gold from the waste material, which assayed 0.06 ounce gold per ton, was readily achieved because the gold occurred as submicroscopic particles in a porous host rock. Gold recovery of 80 percent was obtained in 11 days from material crushed to 1 inch in size, and recovery was 90 percent after 21 days.

Jan 1, 1969

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

By Jr. Gabler

Because of concern over the availability and reliability of an uninterrupted supply of manganese and other materials, the U.S. Congress requested that the U.S. Bureau of Mines (USBM) study the /low of strategic and critical materials in the economy to delineate and quantify the production areas where metal values are lost. As a result, the USBM developed a generic computerized commodity flow model that is readily amenable to updating. The original model developed for cobalt, with slight modifications, was used to track the flow of manganese. This report follows the flow of manganese through its metallurgical and chemical applications and highlights areas where significant losses occur owing to downgrading, export, or disposal. The study indicates that materials containing 695,000 short tons (st) of manganese were consumed domestically in 1990. Scrap recovery specifically for manganese recycling was insignificant. However, considerable manganese was recycled through processing operations as a minor component of ferrous and nonferrous scrap and steel slag. The major loss category is manganese lost in steel processing, 323,156 st or 46 pet of the 1990 apparent consumption. Most of this loss reports to steelmaking slags. Recovery from slags is technically feasible, but is not economically feasible.

Jan 1, 1995

By H. Kenworthy

Laboratory experiments were conducted on several materials to determine their suitability for the production of mineral wool. By blending raw charges in the proper proportions and in some instances by adding lime, acceptable wools were made from samples originating in Alaska, Florida, Texas, and Virginia. It was shown that satisfactory wools can be produced from many kinds of raw materials if the ratios of acidic and basic constituents are properly maintained. INTRODUCTION The Federal Bureau of Mines has facilities at the Mississippi Valley Experiment Station, Rolla, Mo., for examining and testing mineral-wool raw materials. Samples are evaluated through small-scale wool-blowing experiments, aided by petrographic, chemical, and physical analyses of the raw materials and finished wools. When enough experimental data have been accumulated they are made public through Government reports and periodicals. This report of investigations follows that published in 19513/ and presents test data on samples received and examined since 1951.

Jan 1, 1956