Search Documents

By Warren Hastings

This paper describes the methods and costs, in units of labor end materials, of sinking a 7 compartment vertical shaft 1,261 feet through a fractured, water-saturated formation. The shaft, designed for hoisting 2,500 tons a day, is at Friedensville, Lehigh County, Pa., approximately 6 miles south of Allentown and Bethlehem. It was sunk by the E. J. Longyear Co. under contract to the New Jersey Zinc Co. Preparation for shaft sinking W8A begun July 1, 1947, and sinking was completed August 18, 1952. A total of 604,858 man hours was required to sink the shaft.

Jan 1, 1954

By J. R. Thoenen

[Before 1914 Germany held virtual monopoly on the world supply of potash for fertilizer purposes. During the world War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-time prices stimulated interest n various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany and other sources reduced prices to below pre-war levels, and, as a result, most of the domestic producers ceased operational.]

Jan 1, 1941

By N. A. Eilertsen

Mining operations were in progress at the Shawangunk mine near Summitville, Sullivan County, N. Y. as early as 1843 and again as late as 1918. Difficulty in effecting mechanical separation of sphalerite and galena was the primary reason for abandonment by various operators. The Bureau of Mines investigated this mine by diamond drilling, sampling, and performing beneficiation tests. The investigation included the construction of 1.25 miles of access road and the completion of 6,526 feet of core drilling in 24 holes. In addition, 151 samples were taken in the mine. The investigation proved an extension of ore contiguous to the old mine workings and resulted in the discovery of another ore shoot at depth. The ore occurs as fissure filling in a fault zone and contains concentrations of zinc and lead sulfides with minor dissemination of chalcopyrite in a quartz gangue. Metallurgical tests indicate that the ore can be concentrated by selective flotation.

Jan 1, 1950

By F. E. Harris

The United States produces about 30 percent of the world output of salt. Numerous deposits occur in widely separated areas, but the leading producing States are California, Kansas, Louisiana, Michigan, New York, Ohio, Texas, Utah, and West Virginia. Although no great amount of salt is produced at present in Pennsylvania, the potential sources in that State recently aroused a good deal of interest. The United States salt industry is highly organized; it comprises fewer companies than when small crude works with primitive methods and equipment eked out salt for local needs, but concentration of output brought about by modern inventions and methods of production has improved the quality of the produce greatly and accelerated production.

Jan 1, 1939

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By A. C. Fieldner

ONE of the important functions of the Bureau of Mines is the, analysis of coal from every coal-mining State and Alaska. These analyses are being published for use of Government officials and the public. In connection with analytical data showing composition and quality of coals of the States, consumers, Producers, and the general public will be interested in a brief description of the geologic structure of the coal basins, typical mining conditions in the several districts, and the principal economic data of the industry. These publications have therefore heel) designed to include such features to present concisely the principal facts regarding occurrence, reserves, duality, characteristics, production, and uses of coals of each producing State.

Jan 1, 1952

By John Paul Gries

This Bureau of Mines report reviews the mineral industry of the Black Hills area, including Butte, Custer, Fall River, Lawrence, Meade, and Penning- ton Counties, S. Dak.; and Crook, Niobrara, and Weston Counties, Wyo. It includes discussion of geological occurrence, processing, and potential of 27 commodities that have been produced from the nine-county area. The value of mineral production exceeds $70 million annually. Gold and petroleum account for two-thirds of the total, followed by clays, cement, sand and gravel, and rock. The combined mineral industries annually consume 268 million kilowatts of electrical energy, 933 million Mcf of gas, and 2 million barrels of fuel oil. Water consumption is about 10,000 gallons per minute. About 2,700 persons are employed on a year-round or significant part-time basis.

Jan 1, 1974

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By T. F. Myners

This paper, describing the concentration methods and costs of Witherbee, Sherman and Company at Mineville, N. Y., is one of the series of papers on milling methods and costs being prepared by the United States Bureau of Mines. It deals principally with the production of high-grade concentrate. ACKNOWLEDGMENT The author is indebted to C. F. Jackson, principal mining engineer, United States Bureau of Mines, to A. M. Cummings, general superintendent of Witherbee, Sherman and Company, and to the company's engineering staff, for assistance in preparing this paper.

Jan 1, 1932

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By J. O. Merritt

The primary objective of this research program was to recommend ranges of minimum luminance for safety in underground metal and nonmetal mining. Visual tasks critical to safety were identified and rank-ordered. Realistic, full-scale, dynamic task simulations encompassing the most important visual components of the critical tasks were installed in a large simulated workspace. Five trained observers performed the six simulated mining tasks under varying levels of luminance. Over 13,000 measurements of visual task performance were used in developing minimum luminance recommendations for the on-foot underground worker and the mobile equipment operator.

Jan 1, 1983

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

1.0 SCOPE AND REGULATIONS 1.1 This specification covers the minimum requirements for material handling and associated equipment including design and materials. 1.2 This specification requires compliance with all federal, state, local laws and regulations which may be applicable including the Occupational Safety and Health Act, Construction Safety Act as well as rules, regulations and standards of the Secretary of Labor.

Jan 1, 1979

By A. C. Fieldner

This report is the fourth of a series of annual summaries of research and technologic work on coal by the Technologic Branch of the Bureau of Mines. The coal research program of the Bureau has been broadened and made more flexible to adapt it to changing conditions and needs of the coal industry, and as a result information as to the properties and composition of coal has been increased and new and improved practices in mining, preparation, and utilization of coal have been devised. The present

Jan 1, 1940

By James A. Wasson

Because of the danger to life and property in a coal mine if an oil or natural gas well should be accidentally intersected during mining operations, certain precautionary measures should be carried out prior to entering previously unmined areas. The locations of all wells both at the surface and at the depth of the coalbed should be accurately determined. The condition of the well should be learned from surface observations, and more importantly, from subsurface examination by geophysical logging devices where possible. It is also desirable to learn the physical properties of the hydrocarbon-bearing rock formation and the hydrocarbon fluids. The major hazard presented by oil or natural gas wells to mining operations is that of explosion and fire due to the rapid release of gas into the mine atmosphere. Wellbore pressure, the principal index of danger, should be determined by one or more of the methods described and by a service company such as those listed in the appendix. Because of high pressures involved and the consequent hazard, much emphasis has been placed on underground storage of natural gas in areas containing minable coalbeds. Maps are shown of the principal coal producing areas and the locations of currently active gas storage reservoirs. A checklist has been included of factors to be considered when mining coal in an area where oil or gas wells exist.

Jan 1, 1973

By S. R. Zimmerley

[In the course of a flotation investi£ation, a siliceous gold ore was ground in a'ball mill to ':1inns 300-meeh. It wa. found that the small amotIDt of _Ius 300-mesh material had a gole.. assay approximately twice that of the oriGinal ore, &~d that this overs.ize nroduct also contained much abrac..ed iron. .,Joreove I the gold assay of the abraded iron t which was !1epnrated ma§metically', ~iVFl.£ eight ti;nes that of the are. These facts suggested that some r31aticnship ex?...,ted between the abnorma11y high gold content an the prese:1ce of brA-cit)" iron. It was decided, therefore, to investigate furt~er th~ Fl.Gsociation of the bold ~ith the iron abraded from the balls during sri~Qing ]

Jan 1, 1937

By P. S. Haury

"INTRODUCTION Many ore deposits were discovered in the Wallapai Mining District, which covers the Cerbat Range in Mohave County, Ariz., during the early period of mining there from about 1865 to the 1890's. A considerable amount of production was obtained from shallow lead carbonate ores that carried considerable gold and silver.Mining was revived in 1906 and again during the First World War, and soma of the mines were deepened into the underlying sulfide zone. Substantial quantities of metal were recovered from two mines, the Golconda and the Tennessee-Schuylkill, that were, developed to depths of 1,600 and 1,400 feet, respectively. The Golconda is credited with $6,500,000 gross productions. 2/ This mine was not operated after 1917. The Tennessee-Schuylkill is still operating after a yield of about 300,000 tons of ore that averaged 4.33 percent lead and 7.74 percent zinc and contained an appreciable amount of gold and silver.Many of the old mines were reopened in 1942 or 1943 under the stimulus of premium prices for lead and zinc. A large proportion of this work was finished with loans from the Reconstruction Finance Corporation. It was believed that a good deal of lead and zinc could be recovered from the mines if a custom mill for concentration of the ores was available locally."

Aug 1, 1947

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948