Search Documents

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness. It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 3.3 to 40.0 pet. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3 + 3 sequence) ranged from 13.3 to 63.3 pet.

Jan 1, 2010

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

By J. E. Miller

Primary standard gas mixtures were developed for more accurate calibration of analytical instruments at the Bureau of Mines Helium Research Center and for calibration of analytical instruments used in the helium conservation program. A 10-kg-capacity balance is used to weigh a 4-kg metal cylinder filled to high pressure (1,800 psi maximum) with the component gases of the desired mixture. At 1,800 psi, a cylinder contains about 60 g of helium, or 420 g of nitrogen. An accuracy of ±0.05 mole-percent or better is claimed for each component in the mixtures.

Jan 1, 1965

By R. G. Dressler

The Federal Bureau of Mines designed, constructed, and operated a demonstration plant at Louisiana, Mo., to produce gasoline, liquid fuels, and organic compounds from coal by a modified Fischer-Tropsch gas-synthesis process. Satisfactory equipment was developed to produce and purify synthesis gas and convert it into the desired products. Coal or coke was gasified with oxygen and steam to make a gas consisting essentially of carbon monoxide, hydrogen, and carbon dioxide. Dust in the raw gas was removed by cyclone separation, water scrubbing, and electrostatic precipitation. Carbon dioxide, hydrogen sulfide, and organic sulfur were removed with diethanolamine, iron oxide, and activated carbon. The gas was passed over iron catalyst and was converted into synthetic liquids, which were then separated and fractionated into gasoline, diesel oil, other liquid fuels, and oxygenated organic compounds. A 39-day continuous run demonstrated the feasibility of the process. Addition of 3 milliliters of tetraethylead per gallon of upgraded (or finished) gasoline gave a product with an octane rating up to 90 by the research method. After a caustic wash, the diesel oil was of a superior quality; its cetane number was 60 or above.

Jan 1, 1961

By K. E. Stanfield

Asphalts from. Wyoming "black oils" are being studied at the Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming. These black oils are characterized by their high-asphalt, high-sulphur, and low-gasoline content and are difficult to refine by present methods into high-octane motor fuels, burning oils, and lubricants. Accordingly, their principal use, at present, is for the manufacture of road oil and asphalt. The present production of black oil could be increased to meet a greater demand. During 1937 the daily production of these crude oils in Wyoming was slightly over 13,000 barrels, while, the estimated potential production from existing wells was 56,000 barrels.

Jan 1, 1939

By Albert E. Long

During the summer and fall of 1948 the Bureau of Mines, in cooperation with the U. S. Geological Survey, conducted 6xperiments in diamond core drilling in the Phosphoria formation in southeastern Idaho and southwestern Wyoming. Nearly all of the diamond core drilling in the Phosphoria formation has been done by mining companies interested in finding and developing phosphate-bearing beds amenable to stripping. The recovery of sludge; and enough core (usually 30 to 60 percent) to identify certain marker beds produced by current drilling practices meets both the primary requirement of mining companies in determining depth of overburden and their secondary need to determine the phosphate content of relatively thick minable units whose general composition and nature are already fairly well established.

Jan 1, 1949

By Ann Hubbs, Vincent Castranova, Jane Y. C. Ma, De-Hwa Chao, Joseph K. H. Ma

AN OVERVIEW OF THE ACTION OF TETRANDRINE ON SILICOSISBecause of the persistent presence of silica dust in the lungs silicosis is a progressive and irreversible disease. At present, there is no proven effective therapy for silicosis. Limited choices of therapeutic intervention with corticosteroids and other immunosuppressive regimens 1,2 have been accepted for some forms of pulmonary fibrosis. These treatments are only minimally effective, and the results provide little understanding of the disease state due to the lack of correlation between drug activity and the mechanism of fibrosis. Thus, continuing effort must be made in the search for effective antifibrotic agents, which may be used to provide a sequential analysis of the fibrotic process and to open the door for further research and clinical development. Tetrandrine is one of hundreds of drugs screened for antifibrotic activity by Chinese scientists. It has been used in China as a treatment for silicosis in open clinical trials3 and in laboratory animals. The action of tetrandrine on pulmonary fibrosis has been attributed to its ability to inhibit particle stimulation of alveolar macrophages, a key cell type central to the fibrotic process, to release oxygen radicals and inflammatory cytokines. Alveolar macrophages (AM) residing on the alveolar wall, are the predominant phagocytic cells of the lungs responsible for pulmonary defense against inhaled microorganisms and other particles and thus play an important role in maintaining the homeostasis of the lungs. 7 Ample evidence suggests that cells of the monocyte-macrophage series play an important role in the immunopathogenesis of pulmonary fibrosis. When upregulated by silica, alveolar macrophages generate reactive oxygen metabolites8·9 which can damage lung parenchyma and release fibrogenic growth factors and cytokines, 10,11 such as interleukin 1 (IL-1), which can induce fibroblast proliferation and collagen synthesis. The cytokine-mediated fibroblast proliferation and collagen synthesis are key steps in the development and progression of pulmonary fibrosis .11 Previous studies by our group have shown that tetrandrine exhibits strong binding affinity to AM and inhibits particle-stimulated respiratory burst activity (oxygen consumption, superoxide anion release, and hydrogen peroxide secretion) in these cells. 13 In addition, studies by Kang et al. 14 have reported that tetrandrine inhibits silica-induced release of fibrogenic factors such as IL-1 which are capable of inducing fibroblast proliferation and collagen synthesis. Reist et al. 15 further suggested that the antifibrotic action of tetrandrine may be mediated in part by the direct effect of this drug on the ability of fibroblasts to respond to proliferative agents. These results indicate that the mechanism of silicosis involves activation of AM and fibroblasts by silica, resulting in abnormal collagen production due to miscommunications between the cell types. Tetrandrine may interrupt this process by direct interaction with the lung cells.

Jan 1, 1998

By D. F. Scott

The purpose of this study was to determine if miners were at risk from exposures to chemicals used in the mining industry and determine the nature and sources of the illnesses and injuries. The U.S. Mine Safety and Health Administration?s (MSHA) employment and accident, injury and illness database was reviewed. There were 2,705 cases of chemical-related injuries and illnesses reported from 1999 through 2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker (cleaning plant operators are responsible for maintenance of plants, media operators are responsible for handling reagents, boney preparation plant operators oversee removal of ?bone? from coal, and crusher workers use large crushers to break mined material). From 1999 through 2006, the rate of ?nonfatal days lost? and ?no days lost? (resulting from injuries) did not change significantly; however, the rate of illnesses decreased significantly. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods and safety culture to ensure that their workers are protected.

Jan 1, 2009

By W. P. Yant

[At the majority of mines where flame safety lamps are used either as working lights or as a means of detecting gas, no check it made on this condition of the various parts of the lamp and their assembly other than a visual ink inspection. Although this inspection should be made carefully in view of tae serious consequence that may follow Vie use of a faulty lama, In many instances the inspection is of a perfunctory nature. The Bureau of Mines has therefore designed a small box or gallery for testing lamps for defects and improper assembly before they are taken into the mine. The test simulates the condition when a lamp is extinguished by its introduction into an explosive mixture and the operator attempts to relight the wick while the lamp contains the explosive mixture. This test is more rigorous than merely subjecting a lighted lamp to an explosive methane-air mixture. In the latter test the products of combustion tend to blanket the propagation of flame from within the lamp to the exterior, especially if there are defects at the top of the gauzes. Moreover, when the lighted lamp is subjected to an explosive methane-air mixture the methane builds up slowly within the lamp until the lower inflammable limit is attained, whereupon a feeble explosion occurs within. If the nonlighted lamps is first filled with the methane-air mixture that gives the maximum violence and is than ignited, the dampening effect of products of combustion is obviated and the strain on defects is]

Jan 1, 1930

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By John Ward Smith

The potential economic value of oil shale depends on the products from thermal degradation of the rock, because no other practical method for producing valuable material from oil shale has been found. Detailed study of thermal degradation behavior can aid in characterizing oil shales and their deposits and in evaluating oil-shale processing methods, Numerous publications describe various pyrolysis properties of oil shales (see surveys 3, 9, 11 and articles 1, 2, 4-8, 10, 12),4 but they do not describe a generally applicable analytical procedure for detailed evaluation of thermal degradation products. The analytical method presented here for such evaluations is designed to provide for: 1. Control of retorting conditions--temperature, heating, rate, reaction atmosphere--plus some control over retort pressure and carrier-gas flow, 2. Precise direct gravimetric measurement of the thermal degradation products--oil, water, gas, and spent charge (residue after thermal treatment of the charge). 3. Samples of all products. 4. Determination of the identities and amounts of gaseous compounds produced. 5. Elemental analysis and gross heating value of all products. 6. Determination of the distribution in the retorting products of the elements present in the original samples.

Jan 1, 1962

By H. Dale Nichols

[The growing importance of the Sundence (Jurassic) formation an a source of oil, in the Rocky Mountain area has prompted the making of a series of porosity determinations of core samples collected. from the reservoir sands of the Lance Creek oil field, Niobrara. County, Wyo. These analyses are preliminary to a stud of fluid and energy relations in the Basal Sundance reservoir of that field, and the determinations of porosity will be used in subsequent studies requiring, calculations of the volumetric capacity of the reservoir and estimation of the reserves of oil and gas. However, the porosity characteristics an of the Sundance sands in the Lance Creek field are factory that affect the solution of many current practical problems of development and operation. Primarily for that reason but also because it is recognized that porosity values of different oil-production sands are of widespread interest throughout the industry, the results of the initial work have been presented in tabular and graphic form with no attempt to evaluate their significance as they relate to the production history of the field.]

Jan 1, 1938

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978

By Benjamin W. Haynes

The Bureau of Mines, in cooperation with the National Oceanic and Atmospheric Administration (NOAA), has updated a 1977 NOAA report prepared by Dames & Moore entitled, "Description of Manganese Nodule Processing Activities for Environmental Studies." This updated report contains detailed flowsheets and descriptions of the five potential first-generation nodule recovery schemes now considered most likely to be used by industry; they are high-temperature gas reduction and ammoniacal leach, Cuprion ammoniacal leach, high-temperature and high-pressure H2S04 leach, reduction and HCI leach, and smelting and H2S04 leach. The first three processes are three-metal recovery schemes (Cu, Ni, and Co) with the option of Mn recovery from the tailings. The remaining two processes are four-metal (Cu, Ni, Co, and Mn) recovery schemes. All except the HCI process are assumed to use a nodule feed rate of 3 million tons per year (dry basis). Final metal products are Co powder and cathode Cu and Ni. A minor amount of Ni is also recovered as powder, and some Cu and Zn are recovered as mixed sulfides. Manganese in the four-metal processes is recovered as either manganese metal or ferromanganese.

Jan 1, 1983

By Robert T. Langland

The Bureau of Mines, at its Denver, Colo., research center, has developed a computer program to solve nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship assumed, the unknown parameters may be evaluated by the Newton-Raphson method of iteration. Variances and covariances of the parameters are derived, based on the propagation of errors. A creep function is established from shale test data as an example of program utility. Program accuracy is compared to the accuracies of other programs in present day use.

Jan 1, 1974

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment: including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that arc recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel al the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Robert L. Kranz

Mining-induced microseismicity data collected by the U.S. Bureau of Mines in a hard-rock mine were analyzed for spatial and temporal patterns that might prove useful for prediction of rock bursts or assessment of rock mass damage changes. Pattern attributes described and illustrated in the previous report (part 1) were applied to the study of aftershock sequences associated with two different stopes. The aftershock sequences were spatially and temporally fractal, and the fractality was maintained for up to 16 h following a sequence progenitor. This suggests mechanical interdependency among the after-shocks. No statistical difference was found in the distributions of fractal dimensions when comparing two different stopes or when comparing aftershock sequences initiated by blasts or bumps. This suggests a lack of sensitivity to both stress perturbation mechanism and local damage states. However, differences between the two stopes were found in other sequence attributes that support inferred differences in the magnitude of stress concentrations and damage near each stope, and over time as a stope is developed.

Jan 1, 2010